The "fsl,85..." style compatible binding was to be deprecated
some time ago.  This patch corrects existing occurrences of
the incorrect binding.  The memory-controller and
l2-cache-controller are the only affected nodes.
Signed-off-by: NBradley Hughes <bhughes@silicontkx.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Update PCI IRQ mapping on TQM85xx platforms: include INTC and INTD on PCI-X
slot and add INTA/INTB mapping for PCMCIA bridge.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds support for MPC8308RDB development board from
Freescale.
Supported devices:
 DUART
 Dual Ethernet
 NOR and NAND flashes
 I2C
 USB in peripheral mode

PCIE support is broken by the commit 3da34aae ("powerpc/fsl: Support
unique MSI addresses per PCIe Root Complex"). Works after revert.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1021 processors have no dedicated ROM to store the QE microcode,
so the fimrware is stored externally, and it is U-Boot responsibility
to load it. It might be that the board is booting without QE, e.g.
currently U-Boot doesn't support QE for P1021MDS boards, which means
that QE isn't initialized, and so the board hangs early at boot.

This patch fixes the issue by marking QE as disabled and checking the
state in the probing code. U-Boot should fixup the state if it
initialized the QE.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

UART2 and UART3 on 460EX/GT have incorrect interrupt mappings right now.
UART2 should be 28 (0x1c) and UART3 29 (0x1d). This patch fixes this and
switches to using decimal number instead of hex, since the AppliedMicro
(AMCC) users manuals describe their inerrupt numbers in decimal.

Thanks to Fabien Proriol for pointing this out.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Fabien Proriol <Fabien.Proriol@jdsu.com>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

According to my schematics, on Lite5200 board ethernet phy uses address
0 (all ADDR lines are pulled down). With this change I can talk to
onboard phy (LXT971) and correctly use autonegotiation.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add dts descriptions for onboard 256 byte I2C eeprom (pcf8582C-2)
and 16MB NOR flash (am29lv652d).
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
[grant.likely@secretlab.ca: added lite5200b eeprom and declared lite5200 gpios]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

P1021 is a dual e500v2 core based SOC with:
* 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board)
* 2 PCIe Controller
* 1 USB2.0 controller
* eSDHC, eSPI, I2C, DUART
* eLBC (NAND, BCSR, PMC0/1)
* Security Engine (SEC 3.3.2)
* Quicc Engine (QE)
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NYu Liu <Yu.Liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable the sharing of MSI interrupt through AMP OSes in the mpc8572ds
dtses.
Signed-off-by: NZhao Chenhui <b26998@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

I believe support was disabled due to issues with earlier versions of
the board/processor.  At worst, adding the ports back into the device
tree should result in enabling ports that don't work on older systems,
so the default should be to enable them.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR
and HDD. After adding appropriate nodes we can program these LEDs from
kernel and user space.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Since USB2 is shared with local bus, either local bus or USB2
should be disabled. By default U-Boot enables local bus, so we
have to disable USB2, otherwise kernel hangs:

 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
 fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
 fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
 hub 1-0:1.0: USB hub found
 hub 1-0:1.0: 1 port detected
 fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
 fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
 <hangs here>

Note that U-Boot doesn't clear 'status' property when it enables
USB2, so we have to comment out the whole node.

To enable USB2, one can issue
'setenv hwconfig usb2:dr_mode=<host|peripheral>' command at the
U-Boot prompt.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds support for eTSEC 2.0 as found in P1020.
The changes include introduction of the group nodes for
the etsec nodes.
Signed-off-by: NSandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it.  Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

ICON is based on the AppliedMicro 440SPe. It is equipped with
64MByte NOR FLASH, SODIMM, Gigabit ethernet, SM502 on PCI(X),
LSI SAS1068E on PCIe0 and custom FPGA on PCIe1.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Katmai needs "reset-type" = "chip reset" (2) to correctly reboot the
board.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add support for PCI-e on the AMCC 460SX boards
Signed-off-by: NTirumala Marri <tmarri@amcc.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.
Signed-off-by: NTorez Smith  <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch renames GE Fanuc boards following the split-up of the GE Fanuc
joint venture. These boards are now made by GE Intelligent platorms.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds NOR Flash, LEDs and PIB support for MPC8568E-MDS
boards. Plus, move bcsr node into localbus node, and add bcsr5
gpio-controller node.

Some platform code modifications were also needed.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the MSI section to the DTS file for the GE PPC9A.
Signed-off-by: NMalcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Support for the SBC610 VPX Single Board Computer from GE (PowerPC MPC8641D).

This patch adds basic support for the on-board flash.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the MSI section to the DTS file for the GE SBC610.
Signed-off-by: NMalcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Correction to interrupt map mask for GE SBC310 XMC site and addition of
alias.
Signed-off-by: NMalcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add the MSI section to the DTS file for the GE SBC310.
Signed-off-by: NMartyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The DIU driver should bind against "fsl,mpc5121-diu"
directly. Add this compatible property to the match
table and fix DTS and platform code accordingly.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Collects several changes needed after applying
previous mpc5121 platform and driver patches:

- Add mpc5121 reset module node
- Clean up and fix NAND description, remove unused properties
  here and correct NAND flash chip size.
- Clean up I2C nodes: remove obsolete "cell-index" properties,
  add "fsl,preserve-clocking" property
- Add I2C RTC node for m41t61 RTC
- Add I2C nodes for AD7414 temperature sensor and AT24C32CD3 EEPROM
- Fix compatible property in DMA node
- Clean up CAN nodes, remove unused "cell-index" properties
- Fix compatible property in DIU node
- USB node changes:
    - use "fsl,mpc5121-usb2-dr" compatible property only
    - remove "port0" and "port1" properties as these are only used
      for multi-port host(MHP) module which is not available
      on MPC5121.
    - use 'fsl,invert-drvvbus' and 'fsl,invert-pwr-fault' in
      USB node for internal PHY to specify polarities
      of the appropriate port pins.
Signed-off-by: NPiotr Ziecik <kosmo@semihalf.com>
Signed-off-by: NWolfgang Denk <wd@denx.de>
Signed-off-by: NDetlev Zundel <dzu@denx.de>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Sync Glacier dts with latest Canyonlands version:

- Add l2 cache support
- Add NDFC support
- Add RTC support
- Add AD7414 hwmon support
- Change EMAC compatible node from emac4 to emac4sync and correct the
  register size
- Add support for ISA holes on 4xx PCI/X/E
  (as done in Benjamin Herrenschmidt's patch for Canyonlands)
- Add Crypto device node
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Sync Arches dts with latest Canyonlands version:

- Add 16k FIFO size to supported EMAC nodes
- Add next-level-cache property
- Add Crypto device node
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds NOR FLASH MTD support to the Katmai (440SPe) dts file.
For this the OPB ranges address is mapped differently (base 0x00000000
-> 0xe0000000). This results in the address being identical to the lower
32bit of its physical address. This is needed for the MTD mapping to work
correctly, since U-Boot will insert the physical addresses of the EBC
chip selects into the EBC ranges property. This is the way its done in
most other 4xx dts files as well.

Additionally with a small whitespace cleanup.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

After these change, when need to work in rtbi mode,
just change phy-connection-type to "rtbi".

Also, this work can be done by u-boot.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a device tree source file for the Nintendo Wii video game console.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Acked-by: NSegher Boessenkool <segher@kernel.crashing.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add a device tree source file for the Nintendo GameCube video game console.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Acked-by: NSegher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Newer revs of the FPGA have a larger SD buffer.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add nodes for PPC440SPe DMA, I2O, XOR engines and Memory
Queue module which are used in the updated PPC440SPe ADMA
driver. Also extend plb ranges property to specify address
ranges for DMA0/1 and I2O engines.
Signed-off-by: NYuri Tikhonov <yur@emcraft.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

- Add nodes for PMC and GTM controllers. GTM4 can be used as a wakeup
  source;

- Add fsl,magic-packet properties to eTSEC nodes, i.e. wake-on-lan
  support. Unlike MPC8313 processors, MPC8315 can resume from deep
  sleep upon magic packet reception.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Describe all LocalBus chipselects on MPC8349E-MITX board. Also add flash
bindings.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add OF descriptions of EEPROM, two GPIO extenders and SPD hanging on I2C
on this board.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>