Requests of an acked epoch are stored on the barrier_acked_requests list. In
case the private bio of such a request completes while IO on the drbd device
is suspended [req_mod(completed_ok)] then the request stays there.

When thawing IO because the fence_peer handler returned, then we use
tl_clear() to apply the connection_lost_while_pending event to all requests
on the transfer-log and the barrier_acked_requests list.

Up to now the connection_lost_while_pending event was not applied
on requests on the barrier_acked_requests list. Fixed that.

I.e. now the connection_lost_while_pending and resend events are
applied to requests on the barrier_acked_requests list. For that
it is necessary that the resend event finishes (local only)
READS correctly.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The DISCARD_CONCURRENT flag should be set on one node and cleared on the
other node.
As the code was before it was theoretical possible that a node accepts the
meta socket, but has to close it later on, and keeps the DISCARD_CONCURRENT
flag.
Correct this by moving the clear_bit(DISCARD_CONCURRENT) where the packet
gets sent.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

DRBD has a concept of request epochs or reorder-domains,
which are separated on the wire by P_BARRIER packets.

Older DRBD is not able to handle zero-sized requests at all,
so we need to map empty flushes to these drbd barriers.

These are the equivalent of empty flushes, and
by default trigger flushes on the receiving side anyways
(unless not supported or explicitly disabled),
so there is no need to handle this differently in newer drbd either.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Since the listening socket is open all the time, it was possible to
get into stable "initial packet S crossed" loops.

* when both sides realize in the drbd_socket_okay() call at the end
  of the loop that the other side closed the main socket you had
  the chance to get into a stable loop with repeated "packet S crossed"
  messages.

* when both sides do not realize with the drbd_socket_okay() call at the end
  of the loop that the other side closed the main socket you had
  the chance to get into a stable loop with alternating "packet S crossed"
  "packet M crossed" messages.

In order to break out these stable loops randomize the behaviour if
such a crossing of P_INITIAL_DATA or P_INITIAL_META packets is detected.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Since now our listening socket is open all the time we will get
connection tries of the peer always in. No need to try it three
times.

This is valid when connecting to older peers as well, it simply
increases the probability that the new version DRBD will accept
a connection instead that it will establish one.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Since the drbd_socket_okay() function itself tests if the the
socket is NULL, the explicit test "if (sock.socket && &msock.socket)"
was redundent.
Apart from that the address opperator ('&') before msock.socket rendered
the test pointless.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In 8.4, we may have bios spanning two activity log extents.
Fixup drbd_al_begin_io() and drbd_al_complete_io() to deal with zero sized bios.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We now can schedule only a specific range of sectors for online verify,
or interrupt a running verify without interrupting the connection.

Had to bump the protocol version differently, we are now 101.
Added verify_can_do_stop_sector() { protocol >= 97 && protocol != 100; }

Also, the return value convention for worker callbacks has changed,
we returned "true/false" for "keep the connection up" in 8.3,
we return 0 for success and <= for failure in 8.4.
Affected: receive_state()
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If you do back to back wait-sync/invalidate on a Primary in a tight loop,
during application IO load, you could trigger a race:
  kernel: block drbd6: FIXME going to queue 'set_n_write from StartingSync'
    but 'write from resync_finished' still pending?

Fix this by changing the order of the drbd_queue_work() and
the wake_up() in dec_ap_pending(), and adding the additional
drbd_flush_workqueue() before requesting the full sync.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In case we want to hard-reset from the local-io-error handler,
we need to call it before notifying the peer or aborting local IO.
Otherwise the peer will advance its data generation UUIDs even
if secondary.

This way, local io error looks like a "regular" node crash,
which reduces the number of different failure cases.
This may be useful in a bigger picture where crashed or otherwise
"misbehaving" nodes are automatically re-deployed.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Fix asserts like
  block drbd0: in got_BlockAck:4634: rs_pending_cnt = -35 < 0 !

We reset the resync lru cache and related information (rs_pending_cnt),
once we successfully finished a resync or online verify, or if the
replication connection is lost.

We also need to reset it if a resync or online verify is aborted
because a lower level disk failed.

In that case the replication link is still established,
and we may still have packets queued in the network buffers
which want to touch rs_pending_cnt.

We do not have any synchronization mechanism to know for sure when all
such pending resync related packets have been drained.

To avoid this counter to go negative (and violate the ASSERT that it
will always be >= 0), just do not reset it when we lose a disk.

It is good enough to make sure it is re-initialized before the next
resync can start: reset it when we re-attach a disk.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We cache the congestion status in mdev->congestion_reason whenever
drbd_congested() was called.
Reset this cached info before reporting it when reading /proc/drbd.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

If the drbd worker thread is synchronously waiting for some userland
callback, we don't want some casual pageout to block on us.
Have drbd_congested() report congestion in that case.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Aborting local requests (not waiting for completion from the lower level
disk) is dangerous: if the master bio has been completed to upper
layers, data pages may be re-used for other things already.
If local IO is still pending and later completes,
this may cause crashes or corrupt unrelated data.

Only abort local IO if explicitly requested.
Intended use case is a lower level device that turned into a tarpit,
not completing io requests, not even doing error completion.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The two unused "global flags" in 8.3 are "per volume" flags in 8.4.
Still, they are unused, so lose them.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We must not look at mdev->actlog, unless we have a get_ldev() reference.
It also does not make much sense to try to disconnect or pull-ahead of
the peer, if we don't have good local data.

Only even consider congestion policies, if our local disk is D_UP_TO_DATE.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

drbd_adm_down() does adm_detach(), which can fail with various error
codes, or be interrupted by a signal.

The interrupted by signal case was not properly handled,
leading to
	block drbd0: ASSERT( mdev->state.disk == D_DISKLESS &&
	                     mdev->state.conn == C_STANDALONE ) in drbd/drbd_worker.c
and further to destroying objects while still in use, and resulting crashes.

Detect the interruption, and take the error path out.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Sometimes, a lower level block device turns into a tar-pit,
not completing requests at all, not even doing error completion.

We can force-detach from such a tar-pit block device,
either by disk-timeout, or by drbdadm detach --force.

Queueing for retry only from the request destruction path (kref hit 0)
makes it impossible to retry affected read requests from the peer,
until the local IO completion happened, as the locally submitted
bio holds a reference on the drbd request object.

If we can only complete READs when the local completion finally
happens, we would not need to force-detach in the first place.

Instead, queue for retry where we otherwise had done the error completion.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

This looks cleaner to me,
and also gets rid of the other ugly if-inside-case-fall-through.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

The logic for when to get or put a reference is in mod_rq_state().

To not get confused in the freeze/thaw respectively resend/restart
paths, or when cleaning up requests waiting for P_BARRIER_ACK, this
also introduces additional state flags:
RQ_COMPLETION_SUSP, and RQ_EXP_BARR_ACK.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

completion_ref will count pending events necessary for completion.
kref is for destruction.

This only introduces these new members of struct drbd_request,
a followup patch will make actual use of them.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The previous commit causes __drbd_make_request() to always return 0.
Change it to void.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

READs will be interesting to at most one connection,
WRITEs should be interesting for all established connections.

Introduce some helper functions to hopefully make this easier to follow.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

DRBD requests (struct drbd_request) are already on the per resource
transfer log list, and carry their epoch number. We do not need to
additionally link them on other ring lists in other structs.

The drbd sender thread can recognize itself when to send a P_BARRIER,
by tracking the currently processed epoch, and how many writes
have been processed for that epoch.

If the epoch of the request to be processed does not match the currently
processed epoch, any writes have been processed in it, a P_BARRIER for
this last processed epoch is send out first.
The new epoch then becomes the currently processed epoch.

To not get stuck in drbd_al_begin_io() waiting for P_BARRIER_ACK,
the sender thread also needs to handle the case when the current
epoch was closed already, but no new requests are queued yet,
and send out P_BARRIER as soon as possible.

This is done by comparing the per resource "current transfer log epoch"
(tconn->current_tle_nr) with the per connection "currently processed
epoch number" (tconn->send.current_epoch_nr), while waiting for
new requests to be processed in wait_for_work().
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch
In 8.4, we don't distinguish between "resource work" and "connection
work" yet, we have one worker for both, as we still have only one connection.

We only ever used the "data.work",
no need to keep the "meta.work" around.

Move tconn->data.work to tconn->sender_work.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked and adapted from drbd 9 devel branch

In 8.4, we still use drbd_queue_work_front(),
so in normal operation, we can not dequeue batches,
but only single items.

Still, followup commits will wake the worker
without explicitly queueing a work item,
so up() is replaced by a simple wake_up().
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

cherry-picked from drbd 9 devel branch.

In preparation of multiple connections, the "barrier number" or
"epoch number" needs to be tracked per-resource, not per connection.
The sequence number space will not be reset anymore.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Meanwhile, this is used to restart failed READ requests as well.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The commit
    drbd: simplify retry path of failed READ requests
simplified it too much:
it just did not do anything for local read errors.

Add the missing req_may_be_completed_not_susp() to the
READ_COMPLETED_WITH_ERROR case.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

BUG: unable to handle kernel NULL pointer dereference at (null)
...
 [<d1e17561>] ? _drbd_bm_set_bits+0x151/0x240 [drbd]
 [<d1e236f8>] ? receive_bitmap+0x4f8/0xbc0 [drbd]

This fixes an off-by-one error in the receive_bitmap() path,
if run-length encoded bitmap transfer is enabled.

If the bitmap is an exact multiple of PAGE_SIZE, which means the visible
capacity of the drbd device is an exact multiple of 128 MiB (for 4k page
size), and bitmap compression (use-rle) is enabled (which became default
with 8.4), and the very last bit is dirty and reported in an rle
comressed bitmap packet, we ended up trying to kmap_atomic a page pointer
that does not exist (bitmap->bm_pages[last index + 1]).

bug introduced by:
    Date:   Fri Jul 24 15:33:24 2009 +0200
    set bits: optimize for complete last word, fix off-by-one-word corner case

made effective by:
    Date:   Thu Dec 16 00:32:38 2010 +0100
    drbd: get rid of unused debug code

    Long time ago, we had paranoia code in the bitmap that allocated one
    extra word, assigned a magic value, and checked on every occasion that
    the magic value was still unchanged.

    That debug code is unused, the extra long word complicates code a bit.
    Get rid of it.

No-one triggered this bug in the last few years, because a large subset
of our userbase is unaffected:
 * typically the last few blocks of a device are not modified
   frequently, and remain unset
 * use-rle was disabled by default in drbd < 8.4
 * those with slightly "odd" device sizes, or
 * drbd internal meta data (which will skew the device size slightly,
   thus makes it harder to have a bug relevant device size)
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

By disabling al-updates one might increase performace. The price for
that is that in case a crashed primary (that had al-updates disabled)
is reintegraded, it will receive a full-resync instead of a bitmap
based resync.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

These macros no longer exist in kernel version v3.5-rc1.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The buffer 'sc.cpu_mask' is a kernel buffer.  If bitmap_parse is used
instead of __bitmap_parse the extra parameter that indicates a kernel
buffer is not needed.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>