The MSR reservation is per CPU and oprofile would only allocate them
on the CPU it was initialized on. Change this to handle all CPUs.

This also fixes a warning about unprotected use of smp_processor_id()
in preemptible kernels.
Signed-off-by: NAndi Kleen <ak@suse.de>

AMD dual core laptops with C1E do not run the APIC timer correctly
when they go idle. Previously the code assumed this only happened
on C2 or deeper.  But not all of these systems report support C2.

Use a AMD supplied snippet to detect C1E being enabled and then disable
local apic timer use.

This supercedes an earlier workaround using DMI detection of specific systems.

Thanks to Mark Langsdorf for the detection snippet.
Signed-off-by: NAndi Kleen <ak@suse.de>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4298/1: fix memory barriers for DMA coherent and SMP platforms
  [ARM] 4295/2: Fix error-handling in pxaficp_ir.c (version 2)
  [ARM] Fix __NR_kexec_load
  [ARM] Export dma_channel_active()
  [ARM] 4296/1: ixp4xx: compile fix
  [ARM] 4289/1: AT91: SAM9260 NAND flash timing

This patch:
- Switches mb/rmb/wmb back to being full-blown DMBs on ARM SMP systems,
  since mb/rmb/wmb are required to order Normal memory accesses as well.
- Enables the use of DMB and ISB on XSC3 (which is an ARMv5TE ISA core
  but conforms to the ARMv6 memory ordering model and supports the
  various ARMv6 barriers.)
- Makes DMA coherent platforms (only ixp23xx at the moment) map
  mb/rmb/wmb to dmb(), as on DMA coherent platforms, DMA consistent
  mappings are done as Normal mappings, which are weakly ordered.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Acked-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch addresses the following issues with the pxa2xx FIr driver:

1. increment overrun error counter and not frame error counter on ICSR1_ROR bit set in ICSR1.
2. drop frames reported with the frame error from the IC.
3. when resetting the receiver and preparing it for the next DMA in pxa_irda_fir_irq() actually clear the Rx FIFO. See description in Table 11-2 in PXA270 Developer's Manual of the RXE bit.

Correction added in version 2: clearing the IC Rx FIFO also has to be done in pxa_irda_fir_dma_tx_irq()
Signed-off-by: NG. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

It's __NR_kexec_load, not __NR_sys_kexec_load
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 2e3646e5 changed the way the
split config tree is built, but failed to also adjust fixdep accordingly
- if changing a config option from or to m, files referencing the
respective CONFIG_..._MODULE (but not the corresponding CONFIG_...)
didn't get rebuilt.

The problem is that trisate symbol are represent with three different
symbols:
    SYMBOL=n => no symbol defined
    SYMBOL=y => CONFIG_SYMBOL defined to '1'
    SYMBOL=m => CONFIG_SYMBOL_MODULE defined to '1'

But conf_split_config do not distingush between the =y and =m case, so
only the =y case is honoured.

This is fixed in fixdep so when a CONFIG symbol with _MODULE is found we
skip that part and only look for the CONFIG_SYMBOL version.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ingo reported that built-in drivers suffered bootup hangs with certain
driver unregistry sequences, due to sysfs breakage.

Do the minimal fix for v2.6.21: only wait if the driver is a module.
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

dma_channel_active() is used by some modules and is part of our
DMA API, so export it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* master.kernel.org:/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] api: Flush the current page right than the next
  [CRYPTO] api: Use the right value when advancing scatterwalk_copychunks

On platforms where flush_dcache_page is needed we're currently flushing
the next page right than the one we've just processed.  This patch fixes
the off-by-one error.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

In the scatterwalk_copychunks loop, We should be advancing by
len_this_page and not nbytes.  The latter is the total length.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was a typo in commit 7632fc8f,
preventing it from working - 32bit binaries crashed hopelessly before
the below fix and work perfectly now.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the scatterwalk_copychunks loop, We should be advancing by
len_this_page and not nbytes.  The latter is the total length.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  Revert "ACPI: parse 2nd MADT by default"

This reverts commit 09fe5835.
http://bugzilla.kernel.org/show_bug.cgi?id=8283Signed-off-by: NLen Brown <len.brown@intel.com>

I've seen this several times on this drive, completely reproducible.

Once it has hung, power needs to be cut from the drive to recover it, a
simple reboot is not enough.  So I'd suggest disabling NCQ on this
drive.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Acked-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix compilation fail for ixp4xx platforms for the case when CONFIG_IXP4XX_INDIRECT_PCI is set. That is due to the check_signature() is appeared in include/linux/io.h.
Signed-off-by: NVladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] SMTC: Fix recursion in instant IPI replay code.
  [MIPS] BCM1480: Fix setting of irq affinity.
  [MIPS] do_page_fault() needs to use raw_smp_processor_id().
  [MIPS] SMTC: Fix false trigger of debug code on single VPE.
  [MIPS] SMTC: irq_{enter,leave} and kstats keeping for relayed timer ints.
  [MIPS] lockdep: Deal with interrupt disable hazard in TRACE_IRQFLAGS
  [MIPS] lockdep: Handle interrupts in R3000 style c0_status register.
  [MIPS] MV64340: Add missing prototype for mv64340_irq_init().
  [MIPS] MT: MIPS_MT_SMTC_INSTANT_REPLAY currently conflicts with PREEMPT.
  [MIPS] EV64120: Include <asm/irq.h> to fix warning.
  [MIPS] Ocelot: Fix warning.
  [MIPS] Ocelot: Give PMON_v1_setup a proper prototype.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Fix arch/ia64/pci/pci.c:571: warning: `return' with a value
  [IA64] Speed up boot - skip unnecessary clock calibration
  [IA64] bugfix stack layout upside-down
  [IA64] Fix possible invalid memory access in ia64_setup_msi_irq()

local_irq_restore -> raw_local_irq_restore -> irq_restore_epilog ->
	smtc_ipi_replay -> smtc_ipi_dq -> spin_unlock_irqrestore ->
	_spin_unlock_irqrestore -> local_irq_restore

The recursion does abort when there is no more IPI queued for a CPU, so
this isn't usually fatal which is why we got away with this for so long
until this was discovered by code inspection.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMark Mason <mason@broadcom.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Original patch posted by Deepak Saxena <dsaxena@plexity.net>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make smtc_setup_irq() update the list of interrupts which need to be
watched by the debug code itself.  Also there is no need to initialize the
IPI swint when running with a single VPE, so don't initialize it.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Between the mtc0 or di instruction that disables interrupts and the
following hazard barrier a processor may still take interrupts.  If an
interrupt is taken after interrupts are disabled but before the state
is updated it will appear to restore_all that it is incorrectly returning
with interrupts disabled.
Signed-off-by: NChris Dearman <chris@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Check the IEP bit for R3000 style processors when checking to see if
interrupts will be reenabled in restore_all.
Signed-off-by: NChris Dearman <chris@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

So until MIPS_MT_SMTC_INSTANT_REPLAY has been rewritten to solve this
issue, don't allow selecting it with PREEMPT.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/pci/pci-ev64120.c:10: warning: implicit declaration of function 'allocate_irqno'
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove unused variable.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Typo/thinko in bba6f6fcSigned-off-by: NTony Luck <tony.luck@intel.com>

Skip clock calibration if cpu being brought online is exactly the same
speed, stepping, etc., as the previous cpu. This significantly reduces
the time to boot very large systems.
Signed-off-by: NJack Steiner <steiner@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

ia64 expects following vm layout:

== low memory
[register-stack grows up]
[memory-stack grows down]
== high memory

But the code assigns the base of the register stack at the
maximum stack size offset from the fixed address where the
stack *might* start.  Stack randomization will result in the
memory stack starting at a lower address than this, and if the
user has set a low stack limit with "ulimit -s", then you can
end up with the register stack above the memory stack (or if
you were very unlucky right on top of it!).

Fix: Calculate the base address for the register stack starting
from the actual address of the memory stack.
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The following 'if' statement in ia64_setup_msi_irq() always fails even
if create_irq() returns <0 value, because variable 'irq' is defined as
unsigned int. It would cause invalid memory access.

        irq = create_irq();
        if (irq < 0)
                return irq;
Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  NetXen: Fix hardware access for ppc architecture.
  sis190: new PHY support
  atl1: save mac address on remove

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IFB]: Fix crash on input device removal
  [BNX2]: Fix link interrupt problem.

The definition of struct ucc_slow puts the guemr register immediately after the
utpt register, when it should be at offset 0x90.  This patch adds the missing
0x52-byte padding.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Correct the alignment of the internal buffer used by the QUICC Engine
SDMA controller to 4Kbytes.  Correct the shift direction in the logic
that sets up the SDMR register for the QUICC Engine SDMA controller.
Signed-off-by: NChuck Meade <chuckmeade@mindspring.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>