Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.

To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver uses incorrect APIs to unmap DMA memory which were
mapped using dma_map_single(). This patch fixes it to use
appropriate APIs for un-mapping DMA memory.
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the execution of loopback test, driver may receive the packets which
are not originated by this test, loopback implementation need to skip those
packets.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qede: min_mtu 46, max_mtu 9600
- Put define for max in qede.h

qlcnic: min_mtu 68, max_mtu 9600

CC: netdev@vger.kernel.org
CC Dept-GELinuxNICDev@qlogic.com
CC: Yuval Mintz <Yuval.Mintz@qlogic.com>
CC: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not
actually performing unicast MAC filtering.
While we're at it - relax a hard-coded limitation that limits each
interface into using at most 15 unicast MAC addresses before turning
promiscuous. Instead utilize the HW resources to their limit.
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to hardware limitation, when transmitting a geneve-encapsulated
packet with more than 32 bytes worth of geneve options the hardware
would not be able to crack the packet and consider it a regular UDP
packet.

This implements the ndo_features_check() in qede in order to prevent
GSO on said transmitted packets.
Signed-off-by: NManish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds GSO support for GRE and UDP tunnels
where outer checksums are enabled.
Signed-off-by: NManish Chopra <manish.chopra@caviumnetworks.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some hypervisors can support MAC hints to their VFs.
Even though we don't have such a hypervisor API in linux, we add
sufficient logic for the VF to be able to receive such hints and
set the mac accordingly - as long as the VF has not been set with
a MAC already.
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds a skeletal implementation of the qede RoCE driver -
The qedr has some dependencies of the state of the underlying base
interface. This adds some logic required with mutual registrations
and the ability to pass updates on 'intresting' events.
Signed-off-by: NRam Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.

For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.

Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
  Set vf vlan protocol 802.1ad:
    ip link set eth0 vf 1 vlan 100 proto 802.1ad
  Set vf to VST (802.1Q) mode:
    ip link set eth0 vf 1 vlan 100 proto 802.1Q
  Or by omitting the new parameter
    ip link set eth0 vf 1 vlan 100
Signed-off-by: NMoshe Shemesh <moshe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get 1 warning when building kernel with W=1:
drivers/net/ethernet/qlogic/qede/qede_main.c:2113:5: warning: no previous prototype for 'qede_set_features' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.

The major differences would be in:
  - Recognizing that VF is running on top of a legacy PF.
  - Returning some slowpath configurations that are no longer needed
    on top of modern PFs, but would be required when working over
    the legacy ones.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.

At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.

While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].

Fixes: 312e0676 ("qede: Utilize xmit_more")
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch touches various prints in the driver - it reduces the
verbosity of some prints [which were previously logged by default]
while adding several new debug prints and modifying others.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change qed* code in trivial manner; This isn't necessarily
semantic-only, but the end result is the same, i.e., no change
should occur from user perspective. Changes include:
  - Using temporary variables to better fit 80-character restrictions.
  - Removal of unused variables & code with no effect.
[plus some additional minor modifications].
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make semantic-only adjustments to qed* drivers, such as:
  - Changes in code indentation.
  - Usage of BIT() macro.
  - re-naming of variables.
  - Re-ordering of variable declerations.
  - Removal of (== 0) and (!= 0) in conditions.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding the necessary logic to prevet statistics reset
on inner-reload introduced a bug, and now statistics
are reset only when re-probing the driver.

Fixes: a0d26d5a ("qed*: Don't reset statistics on inner reload")
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of ndo_vlan_rx_kill_vid() implementation,
qede is requesting firmware to remove the vlan filter.
This currently happens even if the vlan wasn't previously
added [In case device ran out of vlan credits].

For PFs this doesn't cause any issues as the firmware
would simply ignore the removal request. But for VFs their
parent PF is holding an accounting of the configured vlans,
and such a request would cause the PF to fail the VF's
removal request.

Simply fix this for both PFs & VFs and don't remove filters
that were not previously added.

Fixes: 7c1bfcad ("qede: Add vlan filtering offload support")
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses xmit_more optimization to reduce
number of TX doorbells write per packet.
Signed-off-by: NManish <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleanups qede_poll() routine a bit
and allows qede_poll() to do single iteration to handle
TX completion [As under heavy TX load qede_poll() might
run for indefinite time in the while(1) loop for TX
completion processing and cause CPU stuck].
Signed-off-by: NManish <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When handling IP fragmented packets with csum in their
transport header, the csum isn't changed as part of the
fragmentation. As a result, the packet containing the
transport headers would have the correct csum of the original
packet, but one that mismatches the actual packet that
passes on the wire. As a result, on receive path HW would
give an indication that the packet has incorrect csum,
which would cause qede to discard the incoming packet.

Since HW also delivers a notification of IP fragments,
change driver behavior to pass such incoming packets
to stack and let it make the decision whether it needs
to be dropped.
Signed-off-by: NManish <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several user APIs can cause driver to perform an inner-reload.
Currently, doing this would cause the HW/FW statistics of the
adapter to reset, which isn't the expected behavior [statistics
should only reset on explicit unloads].
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action.  So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the interfaces for ieee/cee dcbnl callbacks and registers
them with the kernel.
Signed-off-by: NSudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RoCE driver is going to need a 32-bit chain [current chain implementation
for qed* currently supports only 16-bit producer/consumer chains].

This patch adds said support, as well as doing other slight tweaks and
modifications to qed's chain API.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The New QED firmware contains several fixes, including:
  - Wrong classification of packets in 4-port devices.
  - Anti-spoof interoperability with encapsulated packets.
  - Tx-switching of encapsulated packets.
It also slightly improves Tx performance of the device.

In addition, this firmware contains the necessary logic for
supporting iscsi & rdma, for which we plan on pushing protocol
drivers in the imminent future.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc warns about qed_fill_link possibly accessing uninitialized data:

drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]

While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.

This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.

The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.

As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since driver is using a FW-based GRO implementation, this has some
effects on its ability to cope with GRO enablement/disablement.
As a result, driver must perform an inner-reload as a result of a state
change in the offload configuration of said feature.

[Failure to do so means network stack would continue to receive
aggregated packets even though user requested the feature to be disabled].
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF is currently ignoring the minimum provided by the API,
mistakenly using the maximum for minimum as well.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver incorrectly uses dma_unmap_addr_set() to set
a variable which is in truth a dma_addr_t
[i.e not defined using DEFINE_DMA_UNMAP_ADDR()] and is
being used by the driver flows other than unmapping
physical addresses. This patch fixes driver fastpath
where CONFIG_NEED_DMA_MAP_STATE is not set.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many developers already know that field for reference count of the
struct page is _count and atomic type.  They would try to handle it
directly and this could break the purpose of page reference count
tracepoint.  To prevent direct _count modification, this patch rename it
to _refcount and add warning message on the code.  After that, developer
who need to handle reference count will find that field should not be
accessed directly.

[akpm@linux-foundation.org: fix comments, per Vlastimil]
[akpm@linux-foundation.org: Documentation/vm/transhuge.txt too]
[sfr@canb.auug.org.au: sync ethernet driver changes]
Signed-off-by: NJoonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Yuval Mintz <yuval.mintz@qlogic.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

page_reference manipulation functions are introduced to track down
reference count change of the page.  Use it instead of direct
modification of _count.
Signed-off-by: NJoonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>