Note that critical doorbells are an unimplemented stub just like
other critical or machine check handlers, since we haven't done
support for "levelled" exceptions yet.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The decrementer on BookE acts as a level interrupt and doesn't
need to be re-triggered when going negative. It doesn't go
negative anyways (unless programmed to auto-reload with a
negative value) as it stops when reaching 0.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The doorbells use the content of the PIR register to match messages
from other CPUs. This may or may not be the same as our linux CPU
number, so using that as the "target" is no right.

Instead, we sample the PIR register at boot on every processor
and use that value subsequently when sending IPIs.

We also use a per-cpu message mask rather than a global array which
should limit cache line contention.

Note: We could use the CPU number in the device-tree instead of
the PIR register, as they are supposed to be equivalent. This
might prove useful if doorbells are to be used to kick CPUs out
of FW at boot time, thus before we can sample the PIR. This is
however not the case now and using the PIR just works.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

... where it belongs
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Our handling of debug interrupts on Book3E 64-bit is not quite
the way it should be just yet. This is a workaround to let gdb
work at least for now. We ensure that when context switching,
we set the appropriate DBCR0 value for the new task. We also
make sure that we turn off MSR[DE] within the kernel, and set
it as part of the bits that get set when going back to userspace.

In the long run, we will probably set the userspace DBCR0 on the
exception exit code path and ensure we have some proper kernel
value to set on the way into the kernel, a bit like ppc32 does,
but that will take more work.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

CONFIG_SMP_750 doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use kstrdup when the goal of an allocation is copy a string into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@

-  to = kmalloc(strlen(from) + 1,flag);
+  to = kstrdup(from, flag);
   ... when != \(from = E1 \| to = E1 \)
   if (to==NULL || ...) S
   ... when != \(from = E2 \| to = E2 \)
-  strcpy(to, from);
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use kstrdup when the goal of an allocation is copy a string into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@

-  to = kmalloc(strlen(from) + 1,flag);
+  to = kstrdup(from, flag);
   ... when != \(from = E1 \| to = E1 \)
   if (to==NULL || ...) S
   ... when != \(from = E2 \| to = E2 \)
-  strcpy(to, from);
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Form 1 affinity allows multiple entries in ibm,associativity-reference-points
which represent affinity domains in decreasing order of importance. The
Linux concept of a node is always the first entry, but using the other
values as an input to node_distance() allows the memory allocator to make
better decisions on which node to go first when local memory has been
exhausted.

We keep things simple and create an array indexed by NUMA node, capped at
4 entries. Each time we lookup an associativity property we initialise
the array which is overkill, but since we should only hit this path during
boot it didn't seem worth adding a per node valid bit.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Remove all rcu head inits. We don't care about the RCU head state before
passing it to call_rcu() anyway. Only leave the "on_stack" variants so
debugobjects can keep track of objects on stack.
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently the irqs for the i8042, which historically provides keyboard and
mouse (aux) support, is hardwired in the driver rather than parsing the
dts.  This patch modifies the powerpc legacy IO code to attempt to parse
the device tree for this information, failing back to the hardcoded values
if it fails.
Signed-off-by: NMartyn Welch <martyn.welch@ge.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

At the moment if request_event_sources_irqs() can't allocate or request
the interrupt, it just does a KERN_ERR printk. This may be fine for the
existing RAS code where if we miss an EPOW event it just means that the
event won't be logged and if we miss one of the RAS errors then we could
miss an event that we perhaps should take action on.

But, for the upcoming IO events code that will use event-sources if we
can't allocate or request the interrupt it means we'd potentially miss
an interrupt from the device. So, let's add a WARN_ON() in this error
case so that we're a bit more vocal when something's amiss.

While we're at it, also use pr_err() to neaten the code up a bit.
Signed-off-by: NMark Nelson <markn@au1.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The RAS code has a #define, RAS_VECTOR_OFFSET, that's used in the
check-exception RTAS call for the vector offset of the exception.

We'll be using this same vector offset for the upcoming IO Event interrupts
code (0x500) so let's move it to include/asm/rtas.h and call it
RTAS_VECTOR_EXTERNAL_INTERRUPT.
Signed-off-by: NMark Nelson <markn@au1.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Now we dynamically allocate the paca array, it takes an extra load
whenever we want to access another cpu's paca. One place we do that a lot
is per cpu variables. A simple example:

DEFINE_PER_CPU(unsigned long, vara);
unsigned long test4(int cpu)
{
	return per_cpu(vara, cpu);
}

This takes 4 loads, 5 if you include the actual load of the per cpu variable:

    ld r11,-32760(r30)  # load address of paca pointer
    ld r9,-32768(r30)   # load link address of percpu variable
    sldi r3,r29,9       # get offset into paca (each entry is 512 bytes)
    ld r0,0(r11)        # load paca pointer
    add r3,r0,r3        # paca + offset
    ld r11,64(r3)       # load paca[cpu].data_offset

    ldx r3,r9,r11       # load per cpu variable

If we remove the ppc64 specific per_cpu_offset(), we get the generic one
which indexes into a statically allocated array. This removes one load and
one add:

    ld r11,-32760(r30)  # load address of __per_cpu_offset
    ld r9,-32768(r30)   # load link address of percpu variable
    sldi r3,r29,3       # get offset into __per_cpu_offset (each entry 8 bytes)
    ldx r11,r11,r3      # load __per_cpu_offset[cpu]

    ldx r3,r9,r11       # load per cpu variable

Having all the offsets in one array also helps when iterating over a per cpu
variable across a number of cpus, such as in the scheduler. Before we would
need to load one paca cacheline when calculating each per cpu offset. Now we
have 16 (128 / sizeof(long)) per cpu offsets in each cacheline.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Fix smatch warning: constant 0x8000000000000000 is so big it is unsigned long
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need the ability to reset cores for use with kexec/kdump for
SMP systems. Calling this function with the specific core you want
to reset will cause the CPU to spin in reset.
Signed-off-by: NMatthew McClintock <msm@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

There are no BATS on BookE - we have the TLBCAM instead.  Also correct
the page size information to included extended sizes.  We don't actually allow
a 4G page size to be used, so comment on that as well.
Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use for_each_pci_dev() to simplify the code.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The use of "hvc_con_driver" as the name for a file-static "struct
console" with a ".setup" field pointing to an __init function causes
a modpost warning, since a non-initdata structure points to init code.
Using "hvc_console" as the name triggers the hacky "*_console"
workaround in modpost to silence the warning, and is the same thing
that most of the other console drivers already do.

I made the same change in hvsi.c since I happened to notice it was
likely to suffer from the same problem.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Enables support for HMC initiated partition hibernation. This is
a firmware assisted hibernation, since the firmware handles writing
the memory out to disk, along with other partition information,
so we just mimic suspend to ram.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Partition hibernation will use some of the same code as is
currently used for Live Partition Migration. This function
further abstracts this code such that code outside of rtas.c
can utilize it. It also changes the error field in the suspend
me data structure to be an atomic type, since it is set and
checked on different cpus without any barriers or locking.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Since the decrementer and timekeeping code was moved over to using
the generic clockevents and timekeeping infrastructure, several
variables and functions have been obsolete and effectively unused.
This deletes them.

In particular, wakeup_decrementer() is no longer needed since the
generic code reprograms the decrementer as part of the process of
resuming the timekeeping code, which happens during sysdev resume.
Thus the wakeup_decrementer calls in the suspend_enter methods for
52xx platforms have been removed.  The call in the powermac cpu
frequency change code has been replaced by set_dec(1), which will
cause a timer interrupt as soon as interrupts are enabled, and the
generic code will then reprogram the decrementer with the correct
value.

This also simplifies the generic_suspend_en/disable_irqs functions
and makes them static since they are not referenced outside time.c.
The preempt_enable/disable calls are removed because the generic
code has disabled all but the boot cpu at the point where these
functions are called, so we can't be moved to another cpu.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently it is possible for userspace to see the result of
gettimeofday() going backwards by 1 microsecond, assuming that
userspace is using the gettimeofday() in the VDSO.  The VDSO
gettimeofday() algorithm computes the time in "xsecs", which are
units of 2^-20 seconds, or approximately 0.954 microseconds,
using the algorithm

	now = (timebase - tb_orig_stamp) * tb_to_xs + stamp_xsec

and then converts the time in xsecs to seconds and microseconds.

The kernel updates the tb_orig_stamp and stamp_xsec values every
tick in update_vsyscall().  If the length of the tick is not an
integer number of xsecs, then some precision is lost in converting
the current time to xsecs.  For example, with CONFIG_HZ=1000, the
tick is 1ms long, which is 1048.576 xsecs.  That means that
stamp_xsec will advance by either 1048 or 1049 on each tick.
With the right conditions, it is possible for userspace to get
(timebase - tb_orig_stamp) * tb_to_xs being 1049 if the kernel is
slightly late in updating the vdso_datapage, and then for stamp_xsec
to advance by 1048 when the kernel does update it, and for userspace
to then see (timebase - tb_orig_stamp) * tb_to_xs being zero due to
integer truncation.  The result is that time appears to go backwards
by 1 microsecond.

To fix this we change the VDSO gettimeofday to use a new field in the
VDSO datapage which stores the nanoseconds part of the time as a
fractional number of seconds in a 0.32 binary fraction format.
(Or put another way, as a 32-bit number in units of 0.23283 ns.)
This is convenient because we can use the mulhwu instruction to
convert it to either microseconds or nanoseconds.

Since it turns out that computing the time of day using this new field
is simpler than either using stamp_xsec (as gettimeofday does) or
stamp_xtime.tv_nsec (as clock_gettime does), this converts both
gettimeofday and clock_gettime to use the new field.  The existing
__do_get_tspec function is converted to use the new field and take
a parameter in r7 that indicates the desired resolution, 1,000,000
for microseconds or 1,000,000,000 for nanoseconds.  The __do_get_xsec
function is then unused and is deleted.

The new algorithm is

	now = ((timebase - tb_orig_stamp) << 12) * tb_to_xs
		+ (stamp_xtime_seconds << 32) + stamp_sec_fraction

with 'now' in units of 2^-32 seconds.  That is then converted to
seconds and either microseconds or nanoseconds with

	seconds = now >> 32
	partseconds = ((now & 0xffffffff) * resolution) >> 32

The 32-bit VDSO code also makes a further simplification: it ignores
the bottom 32 bits of the tb_to_xs value, which is a 0.64 format binary
fraction.  Doing so gets rid of 4 multiply instructions.  Assuming
a timebase frequency of 1GHz or less and an update interval of no
more than 10ms, the upper 32 bits of tb_to_xs will be at least
4503599, so the error from ignoring the low 32 bits will be at most
2.2ns, which is more than an order of magnitude less than the time
taken to do gettimeofday or clock_gettime on our fastest processors,
so there is no possibility of seeing inconsistent values due to this.

This also moves update_gtod() down next to its only caller, and makes
update_vsyscall use the time passed in via the wall_time argument rather
than accessing xtime directly.  At present, wall_time always points to
xtime, but that could change in future.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Fix world-writable child interface control sysfs attributes
  IB/qib: Clean up properly if qib_init() fails
  IB/qib: Completion queue callback needs to be single threaded
  IB/qib: Update 7322 serdes tables
  IB/qib: Clear 6120 hardware error register
  IB/qib: Clear eager buffer memory for each new process
  IB/qib: Mask hardware error during link reset
  IB/qib: Don't mark VL15 bufs as WC to avoid a rare 7322 chip problem
  RDMA/cxgb4: Derive smac_idx from port viid
  RDMA/cxgb4: Avoid false GTS CIDX_INC overflows
  RDMA/cxgb4: Don't call abort_connection() for active connect failures
  RDMA/cxgb4: Use the DMA state API instead of the pci equivalents

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Enable beep on Realtek codecs with PCI SSID override
  ALSA: usb-audio - Add volume resolution quirk for some Logitech webcams
  ALSA: hda - Add Macbook 5,2 quirk
  ALSA: hda - Fix uninitialized variable

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  writeback: simplify the write back thread queue
  writeback: split writeback_inodes_wb
  writeback: remove writeback_inodes_wbc
  fs-writeback: fix kernel-doc warnings
  splice: check f_mode for seekable file
  splice: direct_splice_actor() should not use pos in sd

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Fix userspace build of ptrace.h
  powerpc: Fix default_machine_crash_shutdown #ifdef botch
  powerpc: Fix logic error in fixup_irqs
  powerpc/iseries: Fix possible null pointer dereference in iSeries_pcibios_fixup_resources
  powerpc: Linux cannot run with 0 cores
  powerpc: Fix feature-fixup tests for gcc 4.5
  powerpc: Disable SPARSE_IRQ by default
  powerpc: Fix compile errors in prom_init_check for gcc 4.5
  powerpc: Fix module building for gcc 4.5 and 64 bit
  powerpc/perf_event: Fix for power_pmu_disable()

Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung

* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: SAMSUNG: Fix on wrong function name for S5PV210 sdhci0
  ARM: S5P6442: Fix PLL setting announce message.
  ARM: SAMSUNG: Fix build without SDHCI controllers for S3C64XX
  ARM: S5PV210: Correct clock register properties
  ARM: S5P: Bug fix on external interrupt for S5P SoCs

Build of ptrace.h failed for assembly because it
pulls in stdint.h.
Use exportable types (__u32, __u64) to avoid the dependency
on stdint.h.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Andrey Volkov <avolkov@varma-el.com>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

crash_kexec_wait_realmode() is defined only if CONFIG_PPC_STD_MMU_64
and CONFIG_SMP, but is called if CONFIG_PPC_STD_MMU_64 even if !CONFIG_SMP.
Fix the conditional compilation around the invocation.
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When SPARSE_IRQ is set, irq_to_desc() can
return NULL. While the code here has a
check for NULL, it's not really correct.
Fix it by separating the check for it.

This fixes CPU hot unplug for me.
Reported-by: NAlastair Bridgewater <alastair.bridgewater@gmail.com>
Cc: stable@kernel.org [2.6.32+]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

I don't know if this is a right fix for the problem
since of_get_property can return NULL.
Since iseries_device_information is used only for informational purpose,
we can skip this function without valid HvSubBusNumber number.
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we configure with CONFIG_SMP=n or set NR_CPUS less than the number of
SMT threads we will set the max cores property to 0 in the
ibm,client-architecture-support structure. On new versions of firmware that
understand this property it obliges and terminates our partition.

Use DIV_ROUND_UP so we handle not only the CONFIG_SMP=n case but also the
case where NR_CPUS isn't a multiple of the number of SMT threads.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The feature-fixup test declare some extern void variables and then take
their addresses.  Fix this by declaring them as extern u8 instead.

Fixes these warnings (treated as errors):

  CC      arch/powerpc/lib/feature-fixups.o
cc1: warnings being treated as errors
arch/powerpc/lib/feature-fixups.c: In function 'test_cpu_macros':
arch/powerpc/lib/feature-fixups.c:293:23: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:294:9: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:297:2: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:297:2: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c: In function 'test_fw_macros':
arch/powerpc/lib/feature-fixups.c:306:23: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:307:9: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:310:2: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:310:2: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c: In function 'test_lwsync_macros':
arch/powerpc/lib/feature-fixups.c:321:23: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:322:9: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:326:3: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:326:3: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:329:3: error: taking address of expression of type 'void'
arch/powerpc/lib/feature-fixups.c:329:3: error: taking address of expression of type 'void'
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The SPARSE_IRQ considerably adds overhead to critical path of IRQ
handling.  However it doesn't benefit much in space for most systems with
limited IRQ_NR.  Should be disabled unless really necessary.
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>