This patch adds new logic to support a clock gating feature found on the
latest set of chipsets. The clock gating is performed on the tx/rx
engines when the link is disconnected. Clock gating helps in reducing
power consumption.

* modified based on comments from netdev
Signed-off-by: NAyaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: netdev@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	Documentation/isdn/00-INDEX
	drivers/net/wireless/iwlwifi/iwl-scan.c
	drivers/net/wireless/rndis_wlan.c
	net/mac80211/main.c

This reverts commit 01198304.

Causes warnings in the build as reported by Stephen Rothwell.
So this change is worse than what it's curing.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ignore link partner advertising flags while AN is not complete.

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mdio_support and lp_advertising fields to ethtool_cmd.  Set these
in mdio45_ethtool_gset{,_npage}().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements the ETHTOOL_SPAUSEPARAM operation for MDIO (clause 45)
PHYs with auto-negotiation MMDs.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This converts flow control capabilites to an advertising mask and can
be useful in combination with mii_resolve_flowctrl_fdx().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a shorter and more comprehensible formulation of the
conditions for each flow control mode.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile-tested only.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.

Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These roughly mirror many of the MII library functions and are based
on code from the sfc driver.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IEEE 802.3 clause 45 specifies the MDIO interface and registers for
use in 10G and other PHYs, similar to the MII management interface.

PHYs may have up to 32 MMDs corresponding to different sub-layers and
functions, each with up to 65536 registers.  These are addressed by
PRTAD (similar to the MII PHY address) and DEVAD.  Define a mapping
for specifying PRTAD and DEVAD through the existing MII ioctls.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a PORT_OTHER to represent all other physical port types.  Current
NICs generally do not allow switching between multiple port types in
software so specific types should not be needed.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On several mv643xx_eth hardware versions, the two 64bit mib counters
for 'good octets received' and 'good octets sent' are actually 32bit
counters, and reading from the upper half of the register has the same
effect as reading from the lower half of the register: an atomic
read-and-clear of the entire 32bit counter value.  This can under heavy
traffic occasionally lead to small numbers being added to the upper
half of the 64bit mib counter even though no 32bit wrap has occured.

Since we poll the mib counters at least every 30 seconds anyway, we
might as well just skip the reads of the upper halves of the hardware
counters without breaking the stats, which this patch does.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, when OOM occurs during rx ring refill, mv643xx_eth will get
into an infinite loop, due to the refill function setting the OOM bit
but not clearing the 'rx refill needed' bit for this queue, while the
calling function (the NAPI poll handler) will call the refill function
in a loop until the 'rx refill needed' bit goes off, without checking
the OOM bit.

This patch fixes this by checking the OOM bit in the NAPI poll handler
before attempting to do rx refill.  This means that once OOM occurs,
we won't try to do any memory allocations again until the next invocation
of the poll handler.

While we're at it, change the OOM flag to be a single bit instead of
one bit per receive queue since OOM is a system state rather than a
per-queue state, and cancel the OOM timer on entry to the NAPI poll
handler if it's running to prevent it from firing when we've already
come out of OOM.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These two memory barriers in performance-critical paths are not needed
on x86.  Even if some other architecture does buffer PCI I/O space
writes, the existing memory-mapped I/O barriers are unlikely to be what
is needed.
Signed-off-by: NJohn Dykstra <john.dykstra1@gmail.com>
Acked-by: NDon Fry <pcnet32@verizon.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In "mac80211: correct wext transmit power handler"
I fixed the wext handler, but forgot to make the default of the
user_power_level -1 (aka "auto"), so that now the transmit power
is always set to 0, causing associations to time out and similar
problems since we're transmitting with very little power. Correct
this by correcting the default user_power_level to -1.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Bisected-by: NNiel Lambrechts <niel.lambrechts@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- ieee80211_wep_init(), which is called with rtnl_lock held, blocks in
   request_module() [waiting for modprobe to load a crypto module].

 - modprobe blocks in a call to flush_workqueue(), when it closes a TTY
   [presumably when it exits].

 - The workqueue item linkwatch_event() blocks on rtnl_lock.

There's no reason for wep_init() to be called with rtnl_lock held, so
just move it outside the critical section.
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were calling pci_enable_wake() twice in a row for both D3_hot
and D3_cold.  This replaces those calls with a call to pci_wake_from_d3()
to avoid issues with PCI PM vs ordering constraints.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o hold the firmware in memory across suspend, since filesystem
  may not be up after resuming.
o reset the chip after requesting firmware, to minimize downtime
  for NC-SI.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o move related fields into netxen_recv_context struct.
o allocate rx buffer and descriptor rings dynamically.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware starting 4.0.402 started supporting link events, disable
it for older firmwares.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100.  It would not read the eeprom.  After
some bisects, I realized this has been like that since forever (at least
2.6.18).  The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state.  I couldn't find a way to
get the device back to a sane state in the probe function.  So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The x_tables are organized with a table structure and a per-cpu copies
of the counters and rules. On older kernels there was a reader/writer 
lock per table which was a performance bottleneck. In 2.6.30-rc, this
was converted to use RCU and the counters/rules which solved the performance
problems for do_table but made replacing rules much slower because of
the necessary RCU grace period.

This version uses a per-cpu set of spinlocks and counters to allow to
table processing to proceed without the cache thrashing of a global
reader lock and keeps the same performance for table updates.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

char bname[5] is too small for the string "X GHz" when the null
terminator is taken into account.  Thus, turning on rate debugging
can crash unless we have lucky stack alignment.

Cc: stable@kernel.org
Reported-by: NParide Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under certain circumstances iwlwifi can get stuck and will no
longer accept scan requests, because the core code (cfg80211)
thinks that it's still processing one. This fixes one of the
points where it can happen, but I've still seen it (although
only with my radio-off-when-idle patch).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.

Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.

This bug has existed since 2.6.25, reported at:
	http://bugzilla.kernel.org/show_bug.cgi?id=12794Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/iwlwifi/iwl3945-base.c:1415: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict

I am pretty sure that this is a compiler bug, so not to worry.  However,
as far as I can see, iwl-3945.o (the only user) and iwl3945-base.o are
always linked into the same module, so the EXPORT_SYMBOL (which causes
the problem) should not be needed.  Correct?
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Bluetooth 2.1 specification introduced four different security modes
that can be mapped using Legacy Pairing and Simple Pairing. With the
usage of Simple Pairing it is required that all connections (except
the ones for SDP) are encrypted. So even the low security requirement
mandates an encrypted connection when using Simple Pairing. When using
Legacy Pairing (for Bluetooth 2.0 devices and older) this is not required
since it causes interoperability issues.

To support this properly the low security requirement translates into
different host controller transactions depending if Simple Pairing is
supported or not. However in case of Simple Pairing the command to
switch on encryption after a successful authentication is not triggered
for the low security mode. This patch fixes this and actually makes
the logic to differentiate between Simple Pairing and Legacy Pairing
a lot simpler.

Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Bluetooth stack uses a reference counting for all established ACL
links and if no user (L2CAP connection) is present, the link will be
terminated to save power. The problem part is the dedicated pairing
when using Legacy Pairing (Bluetooth 2.0 and before). At that point
no user is present and pairing attempts will be disconnected within
10 seconds or less. In previous kernel version this was not a problem
since the disconnect timeout wasn't triggered on incoming connections
for the first time. However this caused issues with broken host stacks
that kept the connections around after dedicated pairing. When the
support for Simple Pairing got added, the link establishment procedure
needed to be changed and now causes issues when using Legacy Pairing

When using Simple Pairing it is possible to do a proper reference
counting of ACL link users. With Legacy Pairing this is not possible
since the specification is unclear in some areas and too many broken
Bluetooth devices have already been deployed. So instead of trying to
deal with all the broken devices, a special pairing timeout will be
introduced that increases the timeout to 60 seconds when pairing is
triggered.

If a broken devices now puts the stack into an unforeseen state, the
worst that happens is the disconnect timeout triggers after 120 seconds
instead of 4 seconds. This allows successful pairings with legacy and
broken devices now.

Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use a different work_struct variables for add_conn() and del_conn() and
use single work queue instead of two for adding and deleting connections.

It eliminates the following error on a preemptible kernel:

[  204.358032] Unable to handle kernel NULL pointer dereference at virtual address 0000000c
[  204.370697] pgd = c0004000
[  204.373443] [0000000c] *pgd=00000000
[  204.378601] Internal error: Oops: 17 [#1] PREEMPT
[  204.383361] Modules linked in: vfat fat rfcomm sco l2cap sd_mod scsi_mod iphb pvr2d drm omaplfb ps
[  204.438537] CPU: 0    Not tainted  (2.6.28-maemo2 #1)
[  204.443664] PC is at klist_put+0x2c/0xb4
[  204.447601] LR is at klist_put+0x18/0xb4
[  204.451568] pc : [<c0270f08>]    lr : [<c0270ef4>]    psr: a0000113
[  204.451568] sp : cf1b3f10  ip : cf1b3f10  fp : cf1b3f2c
[  204.463104] r10: 00000000  r9 : 00000000  r8 : bf08029c
[  204.468353] r7 : c7869200  r6 : cfbe2690  r5 : c78692c8  r4 : 00000001
[  204.474945] r3 : 00000001  r2 : cf1b2000  r1 : 00000001  r0 : 00000000
[  204.481506] Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM Segment kernel
[  204.488861] Control: 10c5387d  Table: 887fc018  DAC: 00000017
[  204.494628] Process btdelconn (pid: 515, stack limit = 0xcf1b22e0)
Signed-off-by: NRoger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>