Bump.

Change-ID: Ie280dc67e37a1cf667c3469499a4fb90f4177b75
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In MFP mode particularly when we were setting the PF VSI in limited
promiscuous, the HW switch was still mirroring the outgoing packets
from other VSIs (VF/VMdq) onto the PF VSI.

With this new bit set, the mirroring doesn't happen any more and so
we are in limited promiscuous on the PF VSI in MFP which is similar
to defport.

An API check is not required, since this bit is reserved for FW API
version < 1.5

Also update copyright year in file headers.

Change-ID: I9840cb95f11dde733d943cb03ce84f68b9611bc8
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In one obscure corner case, it was possible to clear the NVM update wait
flag when no update_done message was actually received.  This patch
cleans the event descriptor before use, and moves the opcode check to
where it won't get done if there was no event to clean.

Also update copyright year in file headers.

Change-ID: I68bbc41965e93f4adf07cbe98b9dfd63d41509a4
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a reset fails to complete, the driver gets its affairs in order and
awaits the cold solace of rmmod. Unfortunately, it was not properly
setting the adapter state, which would cause a panic on rmmod, instead
of the desired surcease.

Set the adapter state to DOWN in this case, and avoid a panic.

Change-ID: I6fdd9906da52e023f8dc744f7da44b5d95278ca9
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.

Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Explain why we cannot remove this code, even though it works differently
than any of our other interrupt cause handling code.

Change-ID: Ie66203bd037a466066036611c31d44f759ec5176
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The queues should never be enabled/disabled in the interrupt handler,
ICR0 interrupt enable should be the only thing that needs to be
dynamically changed in the handler.

This patch fixes that. Without this patch X722 platforms were
seeing weird ping timings when in Legacy mode since it takes
a whole lot of time for the HW/FW to re-enable queues.

Change-ID: If065afc45d81c5a19d4a94a00cd5b8f61cefc40c
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the case where we have a page fully used by receive data, we need to
release the page fully to the stack. Instead of calling get_page (which
increments the page count) followed by free_page (which decrements the
page count), just donate our reference to the stack. Although this
donation is not tax deductible, it does allow us to avoid two very
expensive atomic operations that reverse each other.

Change-ID: If70739792d5748995fc175ec92ac2171ed4ad8fc
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.

Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.

Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.

Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch falls back to enabling unicast, multicast and
broadcast promiscuous mode when the driver must disable it's use
of "default port" aka defport mode (which is normally used to
provide a promiscuous mode), due to internal incompatibility
with Multiple Function per Port (aka MFP).

The situation that requires this patch is when Physical
Function 0 is the device being used, and it can support SR-IOV
when MFP is enabled, via the driver creating a VEB on an MFP
enabled adapter.

Change-ID: Ie90b00d0d58782a5dfcf2c3c9725a2eb90bd63d8
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.

Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.

Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes use of a pointer called hw consistent
in the i40e_remove function.

Change-ID: Idacc7ff0a09a68289c57457a78618bf5497de077
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Support packet split receive on VFs. This is off by default but can be
enabled using ethtool private flags. Because we need to trigger a reset
from outside of i40evf_main.c, create a new function to do so, and
export it.

Also update copyright year in file headers.

Change-ID: I721aa5d70113d3d6d94102e5f31526f6fc57cbbb
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There was a completely unused file "dump" in debugfs that
never panned out to be useful.

Change-ID: I12bb9e37b5a83299725dda815a8746157baf6562
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We have a define for this, use it. No functional change.

Change-ID: Ic0e3ea4f562e46de63b2a8de07f291ccc10205fd
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Jiri Benc says:

====================
vxlan: clean up rx path, consolidating extension handling

The rx path of VXLAN turned over time into kind of spaghetti code. The rx
processing is split between vxlan_udp_encap_recv and vxlan_rcv but in an
artificial way: vxlan_rcv is just called at the end of vxlan_udp_encap_recv,
continuing the rx processing where vxlan_udp_encap_recv left it. There's no
clear border between those two functions.

It makes sense to combine those functions into one; this will be actually
needed for VXLAN-GPE where we'll need to skip part of the processing which
is hard to do with the current code.

However, both functions are too long already. This patchset is shortening
them, consolidating extension handling that is spread all around together
and moving it to separate functions. (Later patchsets will do more
consolidation in other parts of the functions with the final goal of merging
vxlan_udp_encap_recv and vxlan_rcv.)

In process of consolidation of the extension handling, I needed to deal with
vni field in a generic way, as its lower 8 bits mean different things for
different extensions. While cleaning up the code to strictly distinguish
between "vni" and "vni field" (which contains vni plus an additional byte),
I also converted the code not to convert endianess back and forth.

The full picture can be seen at:
https://github.com/jbenc/linux-vxlan/commits/master
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For metadata based tunnels, VNI is ignored when doing vxlan device lookups
(because such tunnel receives all VNIs). However, this was not honored by
vxlan_xmit_one when doing encapsulation bypass. Move the check for metadata
based tunnel to the common place where it belongs.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there are unrecognized flags present in the vxlan header, it doesn't
make much sense to return the packet for further UDP processing, especially
considering that for other invalid flag combinations we drop the packet
because of previous checks.

This means we return positive value only at the beginning of the function
where tun_dst is not yet allocated. This allows us to get rid of the
bad_flags and error jump labels.

When we're dropping packet, we need to free tun_dst now.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bring the extension handling to a single place and move the actual handling
logic out of vxlan_udp_encap_recv as much as possible.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make vxlan_udp_encap_recv shorter and more comprehensible.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Part of the parameters is not needed. Simplify the caller of this function
in preparation of making vxlan rx more comprehensible.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent repeated conversions from and to network order in the fast path.

To achieve this, define all flag constants in big endian order and store VNI
as __be32. To prevent confusion between the actual VNI value and the VNI
field from the header (which contains additional reserved byte), strictly
distinguish between "vni" and "vni_field".
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, pointer to the vxlan header is kept in a local variable. It has
to be reloaded whenever the pskb pull operations are performed which usually
happens somewhere deep in called functions.

Create a vxlan_hdr function and use it to reference the vxlan header
instead.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-02-17

This series contains updates to i40e/i40evf only (again).

Jesse moves sync_vsi_filters() up in the service_task because it may need
to request a reset, and we do not want to wait another round of service
task time.  Refactored the enable_icr0() in order to allow it to be
decided by the caller whether the CLEARPBA (clear pending events) bit will
be set while re-enabling the interrupt.  Also provides the "Don't Give Up"
patch, where the driver will keep polling trying to allocate receive buffers
until it succeeds.  This should keep all receive queues running even in
the face of memory pressure.  Cleans up the debugging helpers by putting
everything in hex to be consistent.

Neerav updates the DCB firmware version related checkes specific to X710
and XL710 only since the checks are not required for X722 devices.

Shannon adds the use of the new shared MAC filter bit for multicast and
broadcast filters in order to make better use of the filters available
from the device.  Added a parameter to allow the driver to set the
enable/disable of statistics gathering in the hardware switch.  Also the
L2 cloud filtering parameter is removed since it was never used.

Anjali refactors the force_wb and WB_ON_ITR functionality since
Force-WriteBack functionality in X710/XL710 devices has been moved out of
the clean routine and into the service task, so we need to make sure
WriteBack-On-ITR is separated out since it is still called from clean.

Catherine changes the VF driver string to reflect all the products that
are supported.

Mitch refactors the packet split receive code to properly use half-pages
for receives.  Also changes the use of bitwise operators to logical
operators on clean_complete variable, while making a witty reference to
Mr. Spock.  Cleans up (i.e. removes) the hsplit field in the ring
structure and use the existing macro to detect packet split enablement,
which allows debugfs dumps of the VSI to properly show which recevie
routine is in use.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
rocker: do world split

This patchset allows new rocker worlds to be easily added in future.
Two new worlds are now under development: P4 and eBPF.

The main part of the patchset is the OF-DPA carve-out. It resuts in OF-DPA
specific file. Clean cut.

Note this patchset is based on my original attempt in October 2015.
I had to rebase, included all suggestions and did lot of small changes.
Main change to go with all-port-one-world approach. Port world is set according
to what is setup in HW. Not possible to change worlds from driver.

v1->v2:
  patch 12/13:
  - split port_init into pre-init and init
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suggested-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Carve out OF-DPA would specific code from the common file to the world
file. This change required struct rocker and struct rocker_port split
into world specific struct ofdpa and struct ofdpa_port. Along with this
the world specific functions and defines were renamed from prefix
"rocker_" to "ofdpa_".
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to push down rocker flags just to check if this is nowait or
not. Let the caller handle that.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only purpose of passing this parameter is to check for
prepare phase. The only reason for a failure in that state is if
TLVs don't fit into descriptor. That is highly unlikely and if that
happens, it is a driver bug. So remove this parameter from
rocker_cmd_exec, and check for prepare phase in caller.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This avoids need to alloc/free wait structure for every command call.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be consistent with the rest of the setting functions, and pass
"learning" as a bool function parameter.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is another step on the way to per-world clean cut. Introduce world
ops hooks which each world can implement in world-specific way.
Also introduce world infrastructure along with OF-DPA world stub.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And take some other related thing along. They are going to be pushed
into of-dpa part anyway.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a helper to ask HW for the port mode (world).
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Carve out TLV processing helpers into separate files.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since "rocker.c" is going to be split into multiple files, start with
renaming original "rocker.c" file to "rocker_main.c". Multiple code
parts are going to be cut from "rocker_main.c" later on.

Fix couple of checkpatch issues on the way.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since "rocker.h" file is going to be used for different purpose,
rename the hardware-specific header to "rocker_hw.h".
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to pass rocker_port around to alloc/free rocker functions,
since they now use switchdev_trans for memory management storage.
With the param removal, shorten the name of the functions since they now
has nothing to do with rocker port.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
Add support for Classifier and RSS

This patch set enables,

(i) Classifier engine that is used for parsing
through the packet and extracting a search string that is then used
to search a database to find associative data.

(ii) Receive Side Scaling (RSS) that does dynamic load
balancing of the CPUs by controlling the number of messages enqueued
per CPU though the help of Toeplitz Hash function of 4-tuple of
source TCP/UDP port, destination TCP/UDP port, source IPV4 address and
destination IPV4 address.

(iii) Multi queue, to make advantage of RSS

v3: Address review comments from v2
    - reordered local variables from longest to shortlest line

v2: Address review comments from v1
    - fix kbuild warning
    - add default coalescing

v1:
    - Initial version
====================
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NKhuong Dinh <kdinh@apm.com>
Signed-off-by: NTanmay Inamdar <tinamdar@apm.com>
Tested-by: NToan Le <toanle@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>