Kevin discovered that commit c8d82ff6
("ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod
database") broke CORE idle on OMAP3.  This prevents device low power
states.

The root cause is that the 32K sync timer IP block does not support
smart-idle mode[1], and so the hwmod code keeps the IP block in
no-idle mode while it is active.  This in turn prevents the WKUP
clockdomain from transitioning to idle.  There is a hardcoded sleep
dependency that prevents the CORE_L3 and CORE_CM clockdomains from
transitioning to idle when the WKUP clockdomain is active[2], so the
chip cannot enter any device low power states.

It turns out that there is no need to take the 32k sync timer out of
idle.  The IP block itself probably does not have any native idle
handling at all, due to its simplicity.  Furthermore, the PRCM will
never request target idle for this IP block while the kernel is
running, due to the sleep dependency that prevents the WKUP
clockdomain from idling while the CORE_L3 clockdomain is active.  So
we can safely leave the 32k sync timer in target-force-idle mode, even
while we continue to access it.

This workaround is implemented by defining a new clockdomain flag,
CLKDM_ACTIVE_WITH_MPU, that indicates that the clockdomain is
guaranteed to be active whenever the MPU is inactive.  If an IP
block's main functional clock exists inside this clockdomain, and the
IP block does not support smart-idle modes, then the hwmod code will
place the IP block into target force-idle mode even when enabled.  The
WKUP clockdomains on OMAP3/4 are marked with this flag.  (On OMAP2xxx,
no OCP header existed on the 32k sync timer.)   Other clockdomains also
should be marked with this flag, but those changes are deferred until
a later merge window, to create a minimal fix.

Another theoretically clean fix for this problem would be to implement
PM runtime-based control for 32k sync timer accesses.  These PM
runtime calls would need to located in a custom clocksource, since the
32k sync timer is currently used as an MMIO clocksource.  But in
practice, there would be little benefit to doing so; and there would
be some cost, due to the addition of unnecessary lines of code and the
additional CPU overhead of the PM runtime and hwmod code - unnecessary
in this case.

Another possible fix would have been to modify the pm34xx.c code to
force the IP block idle before entering WFI.  But this would not have
been an acceptable approach: we are trying to remove this type of
centralized IP block idle control from the PM code.

This patch is a collaboration between Kevin Hilman <khilman@ti.com>
and Paul Walmsley <paul@pwsan.com>.

Thanks to Vaibhav Hiremath <hvaibhav@ti.com> for providing comments on
an earlier version of this patch.  Thanks to Tero Kristo
<t-kristo@ti.com> for identifying a bug in an earlier version of this
patch.  Thanks to Benoît Cousson <b-cousson@ti.com> for identifying
some bugs in several versions of this patch and for implementation
comments.

References:

1. Table 16-96 "REG_32KSYNCNT_SYSCONFIG" of the OMAP34xx TRM Rev. ZU
   (SWPU223U), available from:
   http://www.ti.com/pdfs/wtbu/OMAP34x_ES3.1.x_PUBLIC_TRM_vzU.zip

2. Table 4-72 "Sleep Dependencies" of the OMAP34xx TRM Rev. ZU
   (SWPU223U)

3. ibid.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The commit 503d0ea2
  ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks

added a wrong "prcm_clk" alias for PRCM clock whereas the McBSP
driver and previous OMAPs are using "prcm_fck".

It thus lead to the following warning.

[   47.409729] omap-mcbsp: clks: could not clk_get() prcm_fck

Fix that by changing the opt_clk role to prcm_fck.
Reported-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NSebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The OMAP4 usb_host_fs (OHCI) and AESS IP blocks require some special
programming for them to enter idle.  Without this programming, they
will prevent the rest of the chip from entering full chip idle.

To implement the idle programming cleanly, this will take some
coordination between maintainers.  This is likely to take some time,
so it is probably best to leave this for 3.6 or 3.7.  So, in the
meantime, prevent these IP blocks from being registered.

Later, once the appropriate support is available, this patch can be
reverted.

This second version comments out the IP block data since Benoît didn't
like removing it.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.

Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.

Tested on OMAP4430/Panda.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In order for suspend/resume dependencies to work correctly, I2C has to
be initialized (more specifically, registered with the driver core)
before MMC.  Without this, the MMC driver fails to adjust the VMMC
regulator (using i2c writes) during the suspend path.

Problem found testing suspend/resume on 3730/OveroSTORM platform.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP4470 currently fails to boot, printing various messages such as ...

omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck
omap_hwmod: mpu: cannot _init_clocks
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4()
omap_hwmod: mpu: couldn't init clocks
Modules linked in:
[<c001c7fc>] (unwind_backtrace+0x0/0xf4) from [<c0043c64>] (warn_slowpath_common+0x4c/0x64)
[<c0043c64>] (warn_slowpath_common+0x4c/0x64) from [<c0043d10>] (warn_slowpath_fmt+0x30/0x40)
[<c0043d10>] (warn_slowpath_fmt+0x30/0x40) from [<c0674208>] (_init+0x2a0/0x2e4)
[<c0674208>] (_init+0x2a0/0x2e4) from [<c067428c>] (omap_hwmod_setup_one+0x40/0x60)
[<c067428c>] (omap_hwmod_setup_one+0x40/0x60) from [<c0674280>] (omap_hwmod_setup_one+0x34/0x60)
[<c0674280>] (omap_hwmod_setup_one+0x34/0x60) from [<c06726f4>] (omap_dm_timer_init_one+0x30/0x250)
[<c06726f4>] (omap_dm_timer_init_one+0x30/0x250) from [<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108)
[<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108) from [<c0672c60>] (omap4_timer_init+0x10/0x5c)
[<c0672c60>] (omap4_timer_init+0x10/0x5c) from [<c066c418>] (time_init+0x20/0x30)
[<c066c418>] (time_init+0x20/0x30) from [<c0668814>] (start_kernel+0x1b0/0x304)
[<c0668814>] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044)
---[ end trace 1b75b31a2719ed1c ]---

The problem is that currently none of the clocks are being registered for
OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics.

This fix allows the kernel to boot without failure using a simple RAMDISK file
system on OMAP4470 blaze board.

Per feedback from Paul and Benoit the 4470 clock data is incomplete for new
modules such as the 2D graphics block that has been added to the 4470.
Therefore add a warning to indicate that the clock data is incomplete.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

commit 8259573b (ARM: OMAP2+: nand: Make board_onenand_init() visible
to board code) broke the build for configs with OneNAND disabled.  By
removing the static in the header file, it created a duplicate definition
in the .c and the .h files, resuling in a build error:

/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.c:102:111: error: redefinition of 'board_onenand_init'
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.h:56:51: note: previous definition of 'board_onenand_init' was here
make[2]: *** [arch/arm/mach-omap2/board-flash.o] Error 1
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [arch/arm/mach-omap2] Error 2
make: *** [sub-make] Error 2

Fix this by removing the duplicate dummy entry from the C file.

Cc: Enric Balletbò i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As per the OMAP4 documentation, audio over HDMI must be transmitted in
no-idle mode. This patch adds the HWMOD_SWSUP_SIDLE so that omap_hwmod uses
no-idle/force-idle settings instead of smart-idle mode.

This is required as the DSS interface clock is used as functional clock
for the HDMI wrapper audio FIFO. If no-idle mode is not used, audio could
be choppy, have bad quality or not be audible at all.
Signed-off-by: NRicardo Neri <ricardo.neri@ti.com>
[b-cousson@ti.com: Update the subject and align the .flags
location with the script template]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit bbd707ac ("ARM: omap2: use
machine specific hook for late init") resulted in the addition of this
sparse warning:

arch/arm/mach-omap2/mux.c:791:12: warning: symbol 'omap_mux_late_init' was not declared. Should it be static?

Fix by including the header file containing the prototype.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>

Increase the timeout for disabling an IP block to five milliseconds.
This is to handle the usb_host_fs idle latency, which takes almost
four milliseconds after a host controller reset.

This is the second of two patches needed to resolve the following
boot warning:

omap_hwmod: usb_host_fs: _wait_target_disable failed

Thanks to Sergei Shtylyov <sshtylyov@mvista.com> for finding
an unrelated hunk in a previous version of this patch.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Tero Kristo <t-kristo@ti.com>

Until the OMAP4 code is converted to disable the use of the clock
framework-based clockdomain enable/disable sequence, any clock used as
a hwmod main_clk must have a clockdomain associated with it.  This
patch populates some clock structure clockdomain names to resolve the
following warnings during kernel init:

omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck.
omap_hwmod: trace_clk_div_ck: missing clockdomain for trace_clk_div_ck.
omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck.
omap_hwmod: ddrphy_ck: missing clockdomain for ddrphy_ck.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>

The 32k sync timer IP block target idle modes in the hwmod data are
incorrect.  The IP block does not support any smart-idle modes.
Update the data to reflect the correct modes.

This problem was initially identified and a diff fragment posted to
the lists by Benoît Cousson <b-cousson@ti.com>.  A patch description
bug in the first version was also identified by Benoît.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>

If an IP is configured in Smart-Standby-Wakeup, when disabling wakeup feature the
IP will not go back to Smart-Standby, but will remain in Smart-Standby-Wakeup.
Signed-off-by: NDjamil Elaidi <d-elaidi@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Commit e813a55e ("OMAP: board-files:
remove custom PD GPIO handling for DVI output") moved TFP410 chip's
powerdown-gpio handling from the board files to the tfp410 driver. One
gpio_request_one(powerdown-gpio, ...) was mistakenly left unremoved in
the Beagle board file. This causes the tfp410 driver to fail to request
the gpio on Beagle, causing the driver to fail and thus the DVI output
doesn't work.

This patch removes several boot errors from board-omap3beagle.c:

 - gpio_request: gpio--22 (DVI reset) status -22
 - Unable to get DVI reset GPIO

There is a combination of leftover code and revision confusion.
Additionally, xM support is currently a hack.

For original Beagleboard this removes the double initialization of GPIO
170, properly configures it as an output, and wraps the initialization
in an if block so that xM does not attempt to request it.

For Beagleboard xM it removes reference to GPIO 129 which was part
of rev A1 and A2 designs, but never functioned. It then properly assigns
beagle_dvi_device.reset_gpio in beagle_twl_gpio_setup and removes the
hack of initializing it high. Additionally, it uses
gpio_set_value_cansleep since this GPIO is connected through i2c.

Unfortunately, there is no way to tell the difference between xM A2 and
A3. However, GPIO 129 does not function on rev A1 and A2, and the TWL
GPIO used on A3 and beyond is not used on rev A1 and A2, there are no
problems created by this fix.

Tested on Beagleboard-xM Rev C1 and Beagleboard Rev B4.
Signed-off-by: NRuss Dill <Russ.Dill@ti.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Here's one more gpio_to_irq conversion that we missed
earlier. Tested with n800 in gadget mode using USB_ETH.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 62285963 (usb: musb: drop a gigantic amount of ifdeferry)
got rid of a bunch of ifdefs in the MUSB code. Looks like the
platform init code is still using these dropped defines though,
which in many cases results the board defaulting always to host
mode.

Currently the situation is that USB_MUSB_HDRC is the main
Kconfig option with additional USB_GADGET_MUSB_HDRC so only
these two should be used to select between host and OTG mode.

Fix the situation for omaps. The following users should fix the
platform init code in a similar way:

Dropped Kconfig option          Current users

USB_MUSB_OTG                    blackfin, davinci, not in Kconfigs
USB_MUSB_PERIPHERAL             davinci, not in Kconfigs
USB_MUSB_HOST                   davinci, not in Kconfigs
USB_MUSB_HDRC_HCD               blackfin, not in Kconfigs
USB_MUSB_OTG                    blackfin, not in Kconfigs

Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 7f28427b (ARM: OMAP2+: Move omap_dsp_reserve_sdram_memblock() to mach-omap2)
moved DSP platform init code, but failed to include memblock.h causing:

arch/arm/mach-omap2/dsp.c: In function 'omap_dsp_reserve_sdram_memblock':
arch/arm/mach-omap2/dsp.c:58: error: implicit declaration of function 'arm_memblock_steal'
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise we will get:

arch/arm/mach-omap2/omap_l3_smx.c: In function ‘omap3_l3_block_irq’:
arch/arm/mach-omap2/omap_l3_smx.c:156: warning: unused variable ‘address’
arch/arm/mach-omap2/omap_l3_smx.c:155: warning: unused variable ‘multi’
arch/arm/mach-omap2/omap_l3_smx.c:154: warning: unused variable ‘initid’
arch/arm/mach-omap2/omap_l3_smx.c:153: warning: unused variable ‘code’
arch/arm/mach-omap2/omap_l3_smx.c: At top level:
arch/arm/mach-omap2/omap_l3_smx.c:68: warning: ‘omap3_l3_code_string’ defined but not used
arch/arm/mach-omap2/omap_l3_smx.c:90: warning: ‘omap3_l3_initiator_string’ defined but not used

Fix it by always showing the L3 error.
Signed-off-by: NTony Lindgren <tony@atomide.com>

The omapdss arch initialization code registers all the output devices as
omap_devices. However, DPI and SDI are not proper omap_devices, as they
do not have any corresponding HWMOD. This leads to crashes or problems
when the platform code tries to use omap_device functions for DPI and
SDI devices.

One such crash was reported by John Stultz <johnstul@us.ibm.com>:

[   18.756835] Unable to handle kernel NULL pointer dereference at
virtual addr8
[   18.765319] pgd = ea6b8000
[   18.768188] [00000018] *pgd=aa942831, *pte=00000000, *ppte=00000000
[   18.774749] Internal error: Oops: 17 [#1] SMP ARM
[   18.779663] Modules linked in:
[   18.782836] CPU: 0    Not tainted  (3.5.0-rc1-dirty #456)
[   18.788482] PC is at _od_resume_noirq+0x1c/0x78
[   18.793212] LR is at _od_resume_noirq+0x6c/0x78
[   18.797943] pc : [<c00307ec>]    lr : [<c003083c>]    psr: 20000113
[   18.797943] sp : ec3abe80  ip : ec3abdb8  fp : 00000006
[   18.809936] r10: ec1148b8  r9 : c08a48f0  r8 : c00307d0
[   18.815368] r7 : 00000000  r6 : 00000000  r5 : ec114800  r4 :
ec114808
[   18.822174] r3 : 00000000  r2 : 00000000  r1 : ec154fe8  r0 :
00000006
[   18.829010] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM
Segment user
[   18.836456] Control: 10c5387d  Table: aa6b804a  DAC: 00000015
[   18.842437] Process sh (pid: 1139, stack limit = 0xec3aa2f0)
[   18.848358] Stack: (0xec3abe80 to 0xec3ac000)

DPI and SDI can be plain platform_devices. This patch changes the
registration from omap_device_register() to platform_device_add().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: NJohn Stultz <johnstul@us.ibm.com>
Tested-by: NJean Pihet <jean.pihet@newoldbits.com>

The commit (bce492c0  ARM: OMAP2+: UART: Fix incorrect population of
default uart pads) removed default uart pads that where getting populated
and which was making rx pin wakeup capable. If uart pads were used in
different mode by any other module then it would fail since the default
pads took over all the uart pins forcefully. With removal of default pads
the rx_pad wakeup for console uart while waking up from off mode is broken.

Utilise the mux api available to probe the availability of mux pins
in uart mode and probe for availability of uart pin in mux mode0
if uart is available as uart pin itself then configure rx pin
as wakeup capable.

This patch itself doesn't cater to all boards. Boards using uart rx wakeup
mechanism should ensure the usage of omap_serial_init_port by configuring
required uart ports and pass necessary mux data, till then this probing of
uart pins can cater to enabling of rx pad wakeup to most of the boards.

This patch can also throw some boot warning from _omap_mux_get_by_name
if pin is requested for availability is not present while dynamically probing
the uart pins availability such boot warnings can be addressed only when board
files are patched with omap_serial_init_port calls passing the right pads
needed for a given port.

Discussion Threads for reference:
http://www.spinics.net/lists/linux-omap/msg69859.html
http://www.spinics.net/lists/linux-omap/msg68659.html

Cc: Felipe Balbi <balbi@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Russ Dill <russ.dill@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
[tony@atomide.com: updated to fix compile when CONFIG_OMAP_MUX is not set]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 3b511201 (ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer)
added support for lis3lv02d accelerometer.

The patch was still using OMAP_GPIO_IRQ which no longer exists.

Fix it by using gpio_to_irq().
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use the more generic SoC family soc_is_am35xx() instead of the specific
cpu_is_omap3517() (which is being removed.)
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Tested-by: NVaibhav Hiremath <hvaibhav@ti.com>
Tested-by: NMark A. Greer <mgreer@animalcreek.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch adds a simple BCH ecc computation api, similar to the
existing Hamming ecc api. It is intended to be used by the MTD layer.
It implements the following features:

- support 4-bit and 8-bit ecc computation
- do not protect user bytes in spare area, only data area is protected
- ecc for an erased NAND page (0xFFs) is also a sequence of 0xFFs

This last feature is obtained by adding a constant polynomial to
the hardware computed ecc. It allows to correct bitflips in blank pages
and is extremely useful to support filesystems such as UBIFS, which expect
erased pages to contain only 0xFFs.

This api has been tested on an OMAP3630 board.

Artem: The OMAP maintainer Tony Lindgren gave us his blessing for merging
this patch via the MTD tree.
Signed-off-by: NIvan Djelic <ivan.djelic@parrot.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add register offsets for GPIO_IRQSTATUS_RAW_0, GPIO_IRQSTATUS_RAW_0
which are present on OMAP4+ processors. Now we can distinguish
conditions applicable to OMAP4,5 and those specific to OMAP24xx
and OMAP3xxx.

Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This cleanup got missed while implementing following:
25db711d gpio/omap: Fix IRQ handling for SPARSE_IRQ
384ebe1c gpio/omap: Add DT support to GPIO driver

Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NTarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

The Chip Identification register on the am35x family of SoCs
has bits 12, 7:5, and 3:2 marked as reserved and are read as
zeroes.  Unfortunately, on other omap SoCs, a 0 bit means a
feature is "Full Use" so the OMAP3_CHECK_FEATURE() macro
called by omap3_check_features() will incorrectly interpret
those zeroes to mean that a feature is present even though it
isn't.  To fix that, the feature bits that are incorrectly
set (namely, OMAP3_HAS_IVA and OMAP3_HAS_ISP) need to be
cleared after all of the calls to OMAP3_CHECK_FEATURE() in
omap3_check_features() are made.
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
[khilman@ti.com: use soc_is_am35xx() instead of cpu_is_am35xx()]
Signed-off-by: NKevin Hilman <khilman@ti.com>

By default, request_irq() will auto-enable the requested IRQ.

For PRCM interrupts, we may want to avoid that until the PM core code
is fully ready to handle the interrupts.  This is particularily true
for IO pad interrupts on OMAP3, which are shared between the hwmod
core and the PRM core.

In order to avoid PRCM IO-chain interrupts until the PM core is ready
to handle them, ready, set the IRQ_NOAUTOEN flag for the PRCM IO-chain
interrupt,  which means it will remain disabled after request_irq().

Then, explicitly enable the PRCM interrupts after the request_irq() in
the PM core (but not in the hwmod core.)

Special thanks to Tero Kristo for suggesting to isolate the fix to
only the IO-chain interrupt on OMAP3 instead of all PRCM interrupts.

Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Without an ->irq_set_wake() method in an irq_chip, calls to
enable_irq_wake() will fail.  This also causes these interrupts to not
be able to abort suspend (via check_wakeup_irqs() in late suspend.)

Currently, we don't implement ->irq_set_wake() for INTC interrupts
because they default to be wakeup enabled by setting the GRPSEL bits
in PM init.  Even though there is no ->irq_set_wake(), we want
enable_irq_wake() to succeed so these interrupts can abort suspend
when necessary.

To fix, set IRQCHIP_SKIP_SET_WAKE flag for all the INTC
interrupts which avoids trying to check irq_chip->irq_set_wake()
and failing when it doesn't exist.

Longer term, we need to implement ->irq_set_wake() for the INTC
which can manage the appropriate GRPSEL bits.
Signed-off-by: NNeilBrown <neilb@suse.de>
[khilman@ti.com: rework changelog]
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently the higher level omapdss platform driver gets the list of
displays in its platform data, and uses that list to create the
omap_dss_device for each display.

With DT, the logical way to do the above is to list the displays under
each individual output, i.e. we'd have "dpi" node, under which we would
have the display that uses DPI. In other words, each output driver
handles the displays that use that particular output.

To make the current code ready for DT, this patch modifies the output
drivers so that each of them creates the display devices which use that
output. However, instead of changing the platform data to suit this
method, each output driver is passed the full list of displays, and the
drivers pick the displays that are meant for them. This allows us to
keep the old platform data, and thus we avoid the need to change the
board files.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We currently have separate device/driver for each DSS HW module. The DPI
and SDI outputs are more or less parts of the DSS or DISPC hardware
modules, but in SW it makes sense to represent them as device/driver
pairs similarly to all the other outputs. This also makes sense for
device tree, as each node under dss will be a platform device, and
handling DPI & SDI somehow differently than the rest would just make the
code more complex.

This patch modifies arch/arm/mach-omap2/display.c to create platform
devices for DPI and SDI, and later patches will implement driver for
them.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Instead of using omap_device_build() to create the omap_devices for DSS
hwmods, create them with a custom function. This will allow us to create
a parent-child hierarchy for the devices so that the omapdss_core device
is parent for the rest of the dss hwmod devices.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:

- Remove struct omap_display_platform_data. It was used just as a
  wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
  dss hwmods do not need the platform data. This should also work better
  for DT, as we can create omapdss device programmatically in generic omap
  boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
  that the dss hwmod drivers can call.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

No need to have an OMAP prefix on these SoCs that are in the family
but arent' really called OMAP.

Simple rename: CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX

No functional change.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated for the driver config change also]
Signed-off-by: NTony Lindgren <tony@atomide.com>

No need to have an OMAP prefix on these SoCs that are in the family
but arent' really called OMAP.

Simple rename: CONFIG_SOC_OMAPTI81XX --> CONFIG_SOC_TI81XX

No functional change.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently cpu_is_omap3517() actually detects any device in the AM35x
family (3517 and no-SGX version 3505.)  To make it more clear what is
being detected, convert the names from 3517 to AM35xx.

This adds a new soc_is_am35xx() which duplicates the cpu_is_omap3517().
In order to avoid cross-tree dependencies with clock-tree changes,
cpu_is_omap3517() is left until the clock changes are merged,
at which point cpu_is_omap3517() will be completely removed.
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Tested-by: NVaibhav Hiremath <hvaibhav@ti.com>
Tested-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
[tony@atomide.com: change to use soc_is_omap instead]
Signed-off-by: NTony Lindgren <tony@atomide.com>

There are several checks for AM35x devices done using

      if (cpu_is_omap3517() || cpu_is_omap3505())

However, since the 3505 is just a 3517 without an SGX, the 3505 check
is redundant because cpu_is_omap3517() will always be true whenever
cpu_is_omap3505() is true.  From <plat/cpu.h>:

 #define cpu_is_omap3505() (cpu_is_omap3517() && !omap3_has_sgx())

Therefore, remove the redunant 3505 checks.  This helps move towards
removal of SoC detection that depends on specific IP detection.
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>
Tested-by: NVaibhav Hiremath <hvaibhav@ti.com>
Tested-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This allows us to pass dma request lines in platform data to
MMC driver the same way as we already do for omap2430 and later.
Signed-off-by: NTony Lindgren <tony@atomide.com>

This hardware exists only on 2430 and later omaps, so there's no
need to have it in plat-omap/devices.c.

Note that we don't have any users for exported omap_dsp_get_mempool_base(),
so we can make it static.
Signed-off-by: NTony Lindgren <tony@atomide.com>

These supplies going to be needed for the twl6040 driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>