Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned

It's pretty much all over the place, changes to different files are independent.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1072) fixes some recently-introduced compile problems
that show up in ehci-hcd when CONFIG_PM is turned off.

	PORT_WAKE_BITS needs to be defined always.

	ehci_port_power() is called during initialization by all the
	EHCI variants other than the PCI version, in which it is
	"defined but not used".  So add a call to it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Simplify processing of completed qtds, and correct handling of short
reads, by removing two state variables:

 - "qtd_status" wasn't needed.  The current URB's status is either
   OK (-EINPROGRESS) or some fault status.  Once a fault appears,
   the queue halts and any later QTDs are immediately removed, so
   no temporary status is needed.  (Or for typical short reads,
   it's not treated as a fault, so no queue halt is needed.)

 - "do_status" was erroneous.  Because of how the queue is set up,
   short control reads can (and should!) be treated like full size
   reads, and cleaned up the usual way.  The status stage will be
   executed transparently, and usbcore handles the choice of whether
   to report this status as unexected.
 
The "do_status" problem caused a rather perplexing timing-dependent
problem with usbtest case 10.  Sometimes it would make the controller
skip a dozen transactions while (wrongly) trying to clean up after a
short transfer.  Fortunately, removing a dcache contention issue made
this become trivial to reproduce (on one test rig), so enough clues
finally presented themselves ... I think this has been around for a
very long time, but was worsened by recent urb->status changes.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled.  Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub.  This approach turns out to be subject to races, resulting
in unnecessary polling.

The patch does away with the method entirely.  Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present.  This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1068b) disables the RD interrupt flag when an OHCI root
hub is suspended with remote wakeup disabled.  Although the spec
clearly states that this flag permits the controller to issue an
interrupt when a resume request from downstream is detected and not
when a local status change occurs, some controllers mistakenly use it
for both types of event.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting.  The setting
is then saved in the do_remote_wakeup flag.

Later on, however, the device_may_wakeup() value can change because of
user activity.  So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup().  This patch (as1076)
makes that change for root hubs in several places.

The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.

And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Provide better comments about qh_completions() and QTD handling.
That code can be *VERY* confusing, since it's evolved over a few
years to cope with both hardware races and silicon quirks.

Remove two unlikely() annotations that match the GCC defaults
(and are thus pointless); add an "else" to highlight code flow.

This patch doesn't change driver behavior.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

R8A66597 is similar to SH7366 USB 2.0 Host/Function module. It can
support SH7366 USB host by changing several R8A66597 code.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the problem that enumeration of a USB device was slow.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver ignored the value of bInterval and revised the problem
that performed interrupt transfer.

ASIX USB Ethernet adapter comes to work with this host controller
by applying this patch.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch refactors some shutdown code so it can be shared between
ehci_stop() and ehci_shutdown().

This also fixes a couple potential bugs:
 - ehci_shutdown() was not locking ehci->lock before halting the HC.
 - ehci_shutdown() didn't disable the watchdog and IAA timers.
 - ehci_stop() was resetting the host controller when it may have been
   running, which the EHCI spec says "may result in undefined behavior".

ehci_stop() was calling port_power() to turn off the ports, which waited
20ms after applying the port change.  The msleep was for the case where
the HC might take 20ms to turn the ports on; since we're shutting them
off, we can avoid the msleep and just use ehci_turn_off_ports().

ehci_stop() doesn't need to clear the intr_enable register or revert
ownership of the companion controllers to the BIOS, because the host
controller reset should have done that.  There might be a buggy host
controller that doesn't follow the reset rules, but for now we assume
it's redundant code and remove it.

[ A subsequent patch will cancel the timers later ... this version
carries forward existing bugs where timers could get re-armed
after they're canceled. ]
Signed-off-by: NSarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed.  These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.

Until now these jobs have been carried out when the root hub is
resumed, not when the controller is.  Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed.  But this is wasteful and
unnecessary.

To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers.  They can call the new routine instead of
resuming their root hubs.  And ohci-pci.c can call it instead of using
its own special-purpose handler.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers.  They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.

To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume.  It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator.  However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications.  This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1063) fixes a bug in the way ohci-hcd resumes its
controllers.  It leaves the Master Interrupt Enable bit turned off.

If the root hub is resumed immediately this won't matter.  But if the
root hub is suspended (say because no devices are plugged in), it won't
ever wake up by itself.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

platform_get_resource() may return null, so although it seems it will never
do so here unless there's a bug elsewhere, it does no harm to be defensive
and test.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMagnus Damm <magnus.damm@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I was converting a semaphore in this file to a mutex when I noticed that
this file has some fairly rampant style problems. Practically every line
has spaces instead of tabs .. Once I cleared that up, checkpatch.pl showed
a number of other problem.. I think this file might be a good one to review
for new style checks that could be added..

Below are the only two remaining which I didn't remove. 

#5083: FILE: drivers/usb/host/u132-hcd.c:2907:
+               error:

WARNING: labels should not be indented
#5087: FILE: drivers/usb/host/u132-hcd.c:2911:
+               stall:

These labels are actually inside a switch statement, and they are right
under "default:". "default:" appears to be exempt and these other label
should be too, or default shouldn't be exempt.

I also deleted a few lines due to single statements inside { } , 

if (is_error()) {
	return;
}

becomes,

if (is_error())
	return;

with one line deleted.
Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According to David Brownell, this feature doesn't require an
experimental designation any longer.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some EHCI fault paths with large control transfers aren't coded.  Avoid
problems by rejecting transfers that may need two qTDs (16+ KB).  This is
mostly paranoia; even 4 KB transfers are rare, and most HCDs use lower
limits (so it's unlikely anyone would ever try such a thing).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

power.power_state is scheduled for removal.  This patch (as1053)
removes all uses of that field from drivers/usb.  Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.

Part of this patch was written by Pavel Machek.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It was pointed out that we found and fixed the cause of the "bogus"
fatal IRQ reports some time ago ... this patch removes the code
which was working around that bug ("status" got clobbered), and a
comment which needlessly confused folk reading this code.

This also includes a minor cleanup to the code which fixed that bug.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.

An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
expression n,d;
@@

(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)

@depends on haskernel@
expression n,d;
@@

- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove two (or one) conditional tests in per-urb isochronous
transfer setup code paths.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Refactor the EHCI "if (handshake()) state = HC_STATE_HALT" idiom,
which appears 4 times, by replacing it with calls to a new function
called handshake_on_error_set_halt().  Saves a few bytes too.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Various minor fixes to some SOC bus glue for EHCI:

 - Remove a bogus copyright (by "me"!) which someone added to the FSL
   driver, and an irrelevant comment.

 - Un-break MODULE_ALIAS() directives after platform_bus hotplugging
   acquired a backwards-incompatible change.  (Which didn't fix ANY
   of the in-tree drivers it prevented from hotplugging -- sigh.)

 - Remove some bogus assignments of platform_bus_type; that's done by
   the platform_bus code.

 - Add some FIXMEs for drivers with that pointless two-level idiom for
   probe() and remove() routines.  ("Obfuscation" is a non-goal.)
   That should help avoid future bus glue which copies that idiom.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This teaches EHCI how to to work around bugs in certain high speed
devices, by accomodating "bulk" packets that exceed the 512 byte
constant value required by the USB 2.0 specification.  (Have a
look at section 5.8.3, paragraphs 1 and 3.)

It also makes the descriptor parsing code warn when it encounters
such bugs.  (We've had reports of maybe two or three such devices,
all pretty recent.)

Such devices are nonconformant.  The proper fix is have the vendors
of those devices do the simple, obvious, and correct thing ... which
will let them be used with USB hosts that don't have workarounds for
this particular vendor bug.  But unless/until they do, we can at least
have one of the high speed HCDs work with such buggy devices.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This limits how long the OHCI port reset loop waits for the hardware
to do its job, if the controller either (a) dies, or (b) can't finish
the reset.  Such limits are always a good idea.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor cleanups to the EHCI code:  revision history is what source
code repositories should have.  Switch to a more standard way to
kick in verbose debugging -- don't be EHCI-specific.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Magnus Damm <damm@igel.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1047) removes the USB_PERSIST Kconfig option, enabling
it permanently.  It also prevents the power/persist attribute from
being created for hub devices; there's no point in having it since
USB-PERSIST is always turned on for hubs.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset.  This is necessary because:

	When some machines go into suspend, they remove power from
	on-board USB devices while retaining suspend current for USB
	controllers.

	The user might well unplug a USB device while the system is
	suspended and then plug it back in before resuming.

A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep.  If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.

Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable USB HCDs,
to allow re-enable auto loading.

[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ).  The timer would then fire at time (0 <= T <
HZ).

Fix them to use round_jiffies(jiffies + HZ);
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch, suggested by Alan Stern, fixes the hung USB issues
on my notebook from suspend/resume cycles.

It does so by eliminating some confusion about the internal state
machine associated with unlinking from the EHCI async schedule ring,
which caused a recent regression:

  http://bugzilla.kernel.org/show_bug.cgi?id=10345Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Make it possible to pass mbus_dram_target_info to the ehci-orion
driver via the platform data, make the ehci-orion driver program
the window registers based on this data if it is passed in, and
make the Orion platform setup code use this method instead of
programming the EHCI mbus window registers by hand.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>