Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 20 2月, 2010 1 次提交
    • M
      omap: musb: Pass board specific data from board file · 884b8369
      由 Maulik Mankad 提交于 
      Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.

Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      884b8369
  3. 16 2月, 2010 3 次提交
  5. 09 1月, 2010 1 次提交
  7. 17 12月, 2009 1 次提交
  9. 12 12月, 2009 2 次提交
  11. 23 11月, 2009 5 次提交
  13. 17 11月, 2009 1 次提交
  15. 10 11月, 2009 1 次提交
  17. 26 10月, 2009 1 次提交
  19. 23 10月, 2009 1 次提交
  21. 21 10月, 2009 1 次提交
    • T
      omap: headers: Move remaining headers from include/mach to include/plat · ce491cf8
      由 Tony Lindgren 提交于 
      Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.

This was done with:

#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"

for header in $headers; do
	old="#include <mach\/$header"
	new="#include <plat\/$header"
	for dir in $omap_dirs; do
		find $dir -type f -name \*.[chS] | \
			xargs sed -i "s/$old/$new/"
	done
	find drivers/ -type f -name \*omap*.[chS] | \
		xargs sed -i "s/$old/$new/"
	for file in $other_files; do
		sed -i "s/$old/$new/" $file
	done
done

for header in $(ls $mach_dir_old/*.h); do
	git mv $header $plat_dir_new/
done
Signed-off-by: NTony Lindgren <tony@atomide.com>
      ce491cf8
  23. 20 10月, 2009 1 次提交
  25. 15 10月, 2009 1 次提交
  27. 25 9月, 2009 1 次提交
  29. 04 9月, 2009 1 次提交
    • P
      OMAP2/3 board-*.c files: read bootloader configuration earlier · b3c6df3a
      由 Paul Walmsley 提交于 
      Most board-*.c files read configuration data from the bootloader in
their .init_machine() function.  This needs to happen earlier, at some
point before omap2_init_common_hw() is called.  This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      b3c6df3a
  31. 29 8月, 2009 2 次提交
  33. 25 7月, 2009 1 次提交
    • J
      OMAP3 SDRC: add support for 2 SDRAM chip selects · 58cda884
      由 Jean Pihet 提交于 
      Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.

This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS

Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers

Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: NJean Pihet <jpihet@mvista.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      58cda884
  35. 29 5月, 2009 1 次提交