Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 15 7月, 2008 4 次提交
    • T
      libata: improve EH internal command timeout handling · 87fbc5a0
      由 Tejun Heo 提交于 
      ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong.  This patch
implements command type based stepped timeouts.  Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.

ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much.  After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.

IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.

This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      87fbc5a0
    • T
      libata: use ULONG_MAX to terminate reset timeout table · d8af0eb6
      由 Tejun Heo 提交于 
      This doesn't introduce any functional changes.  This is to make reset
timeout table consistent with to-be-added command timeout tables.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      d8af0eb6
    • T
      libata: improve EH retry delay handling · 0a2c0f56
      由 Tejun Heo 提交于 
      EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back.  However, this 5 second delay is superflous or excessive
in many cases.  For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.

This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.

As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.

While at it, convert explicit rounding up division to DIV_ROUND_UP().

This change speeds up EH in many cases w/o sacrificing robustness.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      0a2c0f56
    • T
      libata: consistently use msecs for time durations · 341c2c95
      由 Tejun Heo 提交于 
      libata has been using mix of jiffies and msecs for time druations.
This is getting confusing.  As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs.  So, durations are in msecs and
deadlines are in jiffies.  ata_deadline() is added to compute deadline
from a start time and duration in msecs.

While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
      341c2c95
  3. 14 7月, 2008 5 次提交
  5. 13 7月, 2008 14 次提交
  7. 12 7月, 2008 8 次提交
  9. 11 7月, 2008 9 次提交