Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 11 12月, 2009 2 次提交
  3. 11 9月, 2009 1 次提交
  5. 05 9月, 2009 1 次提交
    • J
      dm raid1: do not allow log_failure variable to unset after being set · d2b69864
      由 Jonathan Brassow 提交于 
      This patch fixes a bug which was triggering a case where the primary leg
could not be changed on failure even when the mirror was in-sync.

The case involves the failure of the primary device along with
the transient failure of the log device.  The problem is that
bios can be put on the 'failures' list (due to log failure)
before 'fail_mirror' is called due to the primary device failure.
Normally, this is fine, but if the log device failure is transient,
a subsequent iteration of the work thread, 'do_mirror', will
reset 'log_failure'.  The 'do_failures' function then resets
the 'in_sync' variable when processing bios on the failures list.
The 'in_sync' variable is what is used to determine if the
primary device can be switched in the event of a failure.  Since
this has been reset, the primary device is incorrectly assumed
to be not switchable.

The case has been seen in the cluster mirror context, where one
machine realizes the log device is dead before the other machines.
As the responsibilities of the server migrate from one node to
another (because the mirror is being reconfigured due to the failure),
the new server may think for a moment that the log device is fine -
thus resetting the 'log_failure' variable.

In any case, it is inappropiate for us to reset the 'log_failure'
variable.  The above bug simply illustrates that it can actually
hurt us.

Cc: stable@kernel.org
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
      d2b69864
  7. 24 7月, 2009 2 次提交
  9. 22 6月, 2009 1 次提交
  11. 15 4月, 2009 1 次提交
  13. 03 4月, 2009 2 次提交
  15. 06 1月, 2009 3 次提交
  17. 14 11月, 2008 1 次提交
  19. 30 10月, 2008 1 次提交
  21. 22 10月, 2008 3 次提交
  23. 10 10月, 2008 1 次提交
    • J
      dm raid1: kcopyd should stop on error if errors handled · f7c83e2e
      由 Jonathan Brassow 提交于 
      dm-raid1 is setting the 'DM_KCOPYD_IGNORE_ERROR' flag unconditionally
when assigning kcopyd work.  kcopyd is responsible for copying an
assigned section of disk to one or more other disks.  The
'DM_KCOPYD_IGNORE_ERROR' flag affects kcopyd in the following way:

When not set:
kcopyd will immediately stop the copy operation when an error is
encountered.

When set:
kcopyd will try to proceed regardless of errors and try to continue
copying any remaining amount.

Since dm-raid1 tracks regions of the address space that are (or
are not) in sync and it now has the ability to handle these
errors, we can safely enable this optimization.  This optimization
is conditional on whether mirror error handling has been enabled.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
      f7c83e2e
  25. 25 4月, 2008 8 次提交
  27. 29 3月, 2008 1 次提交
  29. 20 2月, 2008 1 次提交
  31. 14 2月, 2008 1 次提交
  33. 08 2月, 2008 5 次提交
    • J
      dm raid1: report fault status · af195ac8
      由 Jonathan Brassow 提交于 
      This patch adds extra information to the mirror status output, so that
it can be determined which device(s) have failed.  For each mirror device,
a character is printed indicating the most severe error encountered.  The
characters are:
 *    A => Alive - No failures
 *    D => Dead - A write failure occurred leaving mirror out-of-sync
 *    S => Sync - A sychronization failure occurred, mirror out-of-sync
 *    R => Read - A read failure occurred, mirror data unaffected
This allows userspace to properly reconfigure the mirror set.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
      af195ac8
    • J
      dm raid1: handle read failures · 06386bbf
      由 Jonathan Brassow 提交于 
      This patch gives the ability to respond-to/record device failures
that happen during read operations.  It also adds the ability to
read from mirror devices that are not the primary if they are
in-sync.

There are essentially two read paths in mirroring; the direct path
and the queued path.  When a read request is mapped, if the region
is 'in-sync' the direct path is taken; otherwise the queued path
is taken.

If the direct path is taken, we must record bio information so that
if the read fails we can retry it.  We then discover the status of
a direct read through mirror_end_io.  If the read has failed, we will
mark the device from which the read was attempted as failed (so we
don't try to read from it again), restore the bio and try again.

If the queued path is taken, we discover the results of the read
from 'read_callback'.  If the device failed, we will mark the device
as failed and attempt the read again if there is another device
where this region is known to be 'in-sync'.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
      06386bbf
    • J
      dm raid1: fix EIO after log failure · b80aa7a0
      由 Jonathan Brassow 提交于 
      This patch adds the ability to requeue write I/O to
core device-mapper when there is a log device failure.

If a write to the log produces and error, the pending writes are
put on the "failures" list.  Since the log is marked as failed,
they will stay on the failures list until a suspend happens.

Suspends come in two phases, presuspend and postsuspend.  We must
make sure that all the writes on the failures list are requeued
in the presuspend phase (a requirement of dm core).  This means
that recovery must be complete (because writes may be delayed
behind it) and the failures list must be requeued before we
return from presuspend.

The mechanisms to ensure recovery is complete (or stopped) was
already in place, but needed to be moved from postsuspend to
presuspend.  We rely on 'flush_workqueue' to ensure that the
mirror thread is complete and therefore, has requeued all writes
in the failures list.

Because we are using flush_workqueue, we must ensure that no
additional 'queue_work' calls will produce additional I/O
that we need to requeue (because once we return from
presuspend, we are unable to do anything about it).  'queue_work'
is called in response to the following functions:
- complete_resync_work = NA, recovery is stopped
- rh_dec (mirror_end_io) = NA, only calls 'queue_work' if it
                           is ready to recover the region
                           (recovery is stopped) or it needs
                           to clear the region in the log*
                           **this doesn't get called while
                           suspending**
- rh_recovery_end = NA, recovery is stopped
- rh_recovery_start = NA, recovery is stopped
- write_callback = 1) Writes w/o failures simply call
                   bio_endio -> mirror_end_io -> rh_dec
                   (see rh_dec above)
                   2) Writes with failures are put on
                   the failures list and queue_work is
                   called**
                   ** write_callbacks don't happen
                   during suspend **
- do_failures = NA, 'queue_work' not called if suspending
- add_mirror (initialization) = NA, only done on mirror creation
- queue_bio = NA, 1) delayed I/O scheduled before flush_workqueue
              is called.  2) No more I/Os are being issued.
              3) Re-attempted READs can still be handled.
              (Write completions are handled through rh_dec/
              write_callback - mention above - and do not
              use queue_bio.)
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
      b80aa7a0
    • J
      dm raid1: handle recovery failures · 8f0205b7
      由 Jonathan Brassow 提交于 
      This patch adds the calls to 'fail_mirror' if an error occurs during
mirror recovery (aka resynchronization).  'fail_mirror' is responsible
for recording the type of error by mirror device and ensuring an event
gets raised for the purpose of notifying userspace.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
      8f0205b7
    • J
      dm raid1: handle write failures · 72f4b314
      由 Jonathan Brassow 提交于 
      This patch gives mirror the ability to handle device failures
during normal write operations.

The 'write_callback' function is called when a write completes.
If all the writes failed or succeeded, we report failure or
success respectively.  If some of the writes failed, we call
fail_mirror; which increments the error count for the device, notes
the type of error encountered (DM_RAID1_WRITE_ERROR),  and
selects a new primary (if necessary).  Note that the primary
device can never change while the mirror is not in-sync (IOW,
while recovery is happening.)  This means that the scenario
where a failed write changes the primary and gives
recovery_complete a chance to misread the primary never happens.
The fact that the primary can change has necessitated the change
to the default_mirror field.  We need to protect against reading
garbage while the primary changes.  We then add the bio to a new
list in the mirror set, 'failures'.  For every bio in the 'failures'
list, we call a new function, '__bio_mark_nosync', where we mark
the region 'not-in-sync' in the log and properly set the region
state as, RH_NOSYNC.  Userspace must also be notified of the
failure.  This is done by 'raising an event' (dm_table_event()).
If fail_mirror is called in process context the event can be raised
right away.  If in interrupt context, the event is deferred to the
kmirrord thread - which raises the event if 'event_waiting' is set.

Backwards compatibility is maintained by ignoring errors if
the DM_FEATURES_HANDLE_ERRORS flag is not present.
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
      72f4b314
  35. 20 10月, 2007 4 次提交
  37. 10 10月, 2007 1 次提交