Introduces a module parameter to decide whether the physical
port link state is propagated to the network stack or not.
It makes sense not to take the physical port state into account
on machines with more logical partitions that communicate
with each other. This is always possible no matter what the physical
port state is. Thus eHEA can be considered as a switch there.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Lock debugging finds a problem in phy.c and phy_device.c,
this patch fixes it. Tested on an AT91SAM9263-EK board,
kernel 2.6.23-rc4.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to restore multicast settings on resume and after 'ethtool -r'.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

64-bit DMA causes data corruption with atl1.  We don't know why, and Atheros
is working on it.  For now, just use 32-bit DMA.  This is a big hack that is
probably wrong, but it stops the bleeding.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Acked-by: NChris Snook <csnook@redhat.com>
Acked-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

One of the very first things lguest_init() does is a memcpy.  On
Athlon/Duron/K7 or CyrixIII/VIA-C3 or Geode GX/LX, this tries to use
MMX.

memcpy -> _mmx_memcpy -> kernel_fpu_begin -> clts -> paravirt_ops.clts

But we haven't set paravirt_ops.clts yet, so we do the native version
and crash.  The simplest solution is to use __memcpy.

Thanks to Michael Rasenberger for the bug report.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SERIAL_BFIN=m or SERIAL_MUX=m shouldn't allow SERIAL_CORE_CONSOLE=y.

Additionally, this patch fixes whitespace instead of tabs at the
SERIAL_MUX_CONSOLE option.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Intel framebuffer mis-calculated pixel clocks.

The pixel clock (and thus both H and V sync) will be slower than requested, so
if you set the minimum allowed the display may not sync.  In case of really
old CRT display it could theoretically damage it.

I'm using it with PAL TV (using RGB input - SCART connector) and the bug
prevented it from working at all (TV requirements are more strict and made the
bug visible).
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

G33 has 1MB GTT table range.  Fix GTT mapping in case like 512MB aperture
size.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: NDave Airlie <airlied@linux.ie>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

G33 GTT stolen memory is below graphics data stolen memory and be seperate,
so don't subtract it in stolen mem counting.
Signed-off-by: NZhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: NDave Airlie <airlied@linux.ie>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I ran into a few problems.

n_tty_ioctl() for instance:

drivers/char/tty_ioctl.c:799: error: $,1rxstruct termios$,1ry has no
member named $,1rxc_ispeed$,1ry

This is calling the copy interface that is supposed to be using
a termios2 when the new interfaces are defined, however:

	case TIOCGLCKTRMIOS:
		if (kernel_termios_to_user_termios((struct termios __user *)arg, real_tty->termios_locked))
			return -EFAULT;
		return 0;

This is going to write over the end of the userspace
structure by a few bytes, and wasn't caught by you yet
because the i386 implementation is simply copy_to_user()
which does zero type checking.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix off-by-one in month calculations
Add delay for bus accesses to satisfy Tw > 500ns
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NRaphael Assenat <raph@8d.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8942

Use PCI_DMA_* constants instead of own private definitions Fall back to
32-bit DMA mask if a 64-bit one fails
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Acked-by: NJeff Garzik <jeff@garzik.org>
Tested-by: NLars <polynomial-c@gmx.de>
Cc: Alessandro Polverini <alex@nibbles.it>
Cc: <dac@conglom-o.org>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The recent changed to raid5 to allow offload of parity calculation etc
introduced some bugs in the code for growing (i.e.  adding a disk to) raid5
and raid6.  This fixes them
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the quirk enables the SIR part of the SMCf010 device, the 8250 driver
may claim it as a legacy ttyS device, which makes the legacy probe in the
smsc-ircc2 driver fail.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Restores serial functionality for the BCM1480.
Signed-off-by: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch changes the error code when dev0:fun1 was hidden by BIOS to one
more appropriate.
Signed-off-by: NAristeu Rozanski <aris@ruivo.org>
Signed-off-by: NMark Gross <mark.gross@intel.com>
Signed-off-by: NDoug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When EDAC is configured for EDAC DEBUGGING, the debug printk output level
was set TOO high (EMERG). This patch brings it down to a DEBUG level
Signed-off-by: NDoug Thompson <dougthompson@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When the spi_mpc83xx driver receives a tx_buf pointer which is NULL, it
only writes one zero filled word to the transmit register.  If the driver
expects to receive more than one word it will wait forever for a second
receive interrupt.  With this patch the controller will shift out zeroes
until all words have been received.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Tested-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a bitmask typo in the pdc202xx_new PLL frequency detection code
which causes it to truncate an intermediate difference to 26 bits
instead of the correct 30 bits (the PLL's bitwidth).
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Port of Alan's patch for pata_via.c.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Ensure that BLK_DEV_IDE is built-in before allowing BLK_DEV_IDE_PMAC to
be selected.
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Cc: Bret Towe <magnade@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: NDaniel Exner <dex@dragonslave.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method.  In order to achieve that, do
the following changes:

- install the method for all chips, not only HPT36x/370 and improve the code
  formatting by killing the extra tabs while at it;

- add to the end of the 'switch' statement in the method cases for HPT372[AN]
  and HPT374 chips upon which the known SATA cards are based;

- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
  behave correctly;

- move the HPT370[A] cases below the HPT36x case for consistency.

While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bob Ham <rah@bash.sh>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...

Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there.  Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.
Signed-off-by: NAnti Sullin <anti.sullin@artecdesign.ee>
Signed-off-by: NNicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

drivers/usb/serial/bus.c: In function usb_serial_bus_deregister:
drivers/usb/serial/bus.c:185:
warning: passing argument 1 of free_dynids from incompatible pointer type

Above build warning comes when CONFIG_HOTPLUG=n because argument of
free_dynids() in serial/bus.c is a struct usb_serial_driver, not a
struct usb_driver. This is not a runtime bug, because the function
is an empty stub and never dereferences the passed pointer anyway.
Signed-off-by: NSatyam Sharma <satyam@infradead.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this time it is an LCD.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Two of the CDC ACM control requests in the serial gadget have never
been correct, and have been reported to cause serious troubles ... as
in, soft lockup and maybe watchdog reset (depending on hardware).

This patch makes those request fail cleanly, rather than misbehaving.
Someone using CDC ACM should fix them according to the FIXME comments
which now replace the previous bugs.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I would like have the attached patch added to Linux kernel. The three
usb flash memories listed in the patch are being used in Intel's
ClassmatePC and need USB_QUIRK_RESET_RESUME to work reliably when
resuming from ram.

The MP3/MP4/AVI player "Rockchip ROCK MP3" is seen as a USB disk, but fails
if more than 128 sectors (64kB) are sent or requested in a single read or write
command, and disconnects from the USB bus.

Typical kernel log showing the problem is:

usb 3-1: reset high speed USB device using ehci_hcd and address 6
usb 3-1: reset high speed USB device using ehci_hcd and address 6
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
usb 3-1: USB disconnect, address 6

This patch works around the device limitation by adding "Rockchip ROCK MP3"
to unusual USB devices list and limiting data transfers to 64 sectors (32kB)
per command.
Tested on 2.6.23-rc5 (amd64).
Signed-off-by: NMassimiliano Ghilardi <massimiliano.ghilardi@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The D40 needs the same quirks as the other (semi-)professional Nikon cameras.
The patch is against 2.6.23-rc5.

Details:
http://bugs.gentoo.org/show_bug.cgi?id=191431


From: Ortwin Glück <odi@odi.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is based on information sent in by Christian Gothe.

Cc: Christian Gothe <christian.gothe@kapelan.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJaime Velasco Juan <jaime@singular.local>
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the order of list_add_tail() arguments in
usb_store_new_id() so the list can have more than one single element.
Signed-off-by: NNathael Pajani <nathael.pajani@cpe.fr>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

That drive is quite odd. It has 2K sectors, times out getting string
descriptors and needs a quirk.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>