IBSS CSA will require to disconnect if a channel switch fails, but
mac80211 should search and re-connect after this disconnect. To allow
such usage, split off the ibss disconnect process in a separate function
which only performs the disconnect without overwriting nl80211-supplied
parameters.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The channel switch parsing function can be re-used for the IBSS code,
put the common part into an extra function.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[also move/rename chandef_downgrade]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Do not override max_tp_rate, max_tp_rate2 and max_prob_rate configured
according to fixed_rate in minstrel_ht_update_stats throughput computation
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add the capability to use a fixed modulation rate to minstrel rate controller
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since when we detect beacon lost we do active AP probing (using nullfunc
frame or probe request) there is no need to have beacon polling. Flags
IEEE80211_STA_BEACON_POLL seems to be used just for historical reasons.

Change also make that after we start connection poll due to beacon loss,
next received beacon will abort the poll.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove superfluous call and use locally stored previous result.
Signed-off-by: NSergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

No need for ERR_PTR(PTR_ERR()) since there's ERR_CAST, use it.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If it is needed to disconnect multiple virtual interfaces after
(WoWLAN-) suspend, the most obvious approach would be to iterate
all interfaces by calling ieee80211_iterate_active_interfaces()
and then call ieee80211_resume_disconnect() for each one. This
is what the iwlmvm driver does.

Unfortunately, this causes a locking dependency from mac80211's
iflist_mtx to the key_mtx. This is problematic as the former is
intentionally never held while calling any driver operation to
allow drivers to iterate with their own locks held. The key_mtx
is held while installing a key into the driver though, so this
new lock dependency means drivers implementing the logic above
can no longer hold their own lock while iterating.

To fix this, add a new ieee80211_iterate_active_interfaces_rtnl()
function that iterates while the RTNL is already held. This is
true during suspend/resume, so that then the locking dependency
isn't introduced.

While at it, also refactor the various interface iterators and
keep only a single implementation called by the various cases.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Jouni reported that with mac80211_hwsim, multicast TX was causing
crashes due to invalid vif->cab_queue assignment. It turns out that
this is caused by change_interface() getting invoked and not having
the vif->type/vif->p2p assigned correctly before calling the queue
check (ieee80211_check_queues). Fix this by passing the 'external'
interface type to the function and adjusting it accordingly.

While at it, also fix the error path in change_interface, it wasn't
correctly resetting to the external type but using the internal one
instead.

Fortunately this affects on hwsim because all other drivers set the
vif->type/vif->p2p variables when changing iftype. This shouldn't
be needed, but almost all implementations actually do it for their
own internal handling.
Reported-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Seth reports that some APs, notably the Netgear WNDAP360, send
invalid ECSA IEs in probe response frames with the operating
class and channel number both set to zero, even when no channel
switch is being done. As a result, any scan while connected to
such an AP results in the connection being dropped.

Fix this by ignoring any channel switch announcment in probe
response frames entirely, since we're connected to the AP we
will be receiving a beacon (and maybe even an action frame) if
a channel switch is done, which is sufficient.

Cc: stable@vger.kernel.org # 3.10
Reported-by: NSeth Forshee <seth.forshee@canonical.com>
Tested-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

According to 802.11-2012 9.3.2.10, paragraph 4, QoS
data frames with a group address in the Address 1 field
have sequence numbers allocated from the same counter
as non-QoS data and management frames.  Without this
flag, some drivers may not assign sequence numbers, and
in rare cases frames might get dropped.  Set the control
flag accordingly.
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Previously, the mesh STA responds to probe request from legacy STA
but now it will only respond to legacy STA if the legacy STA does include
the specific mesh ID or wildcard mesh ID in the probe request.

The iw patch "iw: scan using meshid" can be used either by legacy STA
or by mesh STA to do active scanning by inserting the mesh ID in the
probe request frame.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Acked-by: NThomas Pedersen <thomas@cozybit.com>
Acked-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether
the start_sched_scan operation is supported or not, but that will not
be correct for all drivers, we're adding scheduled scan to the iwlmvm
driver but it depends on firmware support.

Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers
so that they can control it regardless of implementing the operation.

This currently only affects the TI drivers since they're the only ones
implementing scheduled scan (in a mac80211 driver.)
Acked-by: NLuciano Coelho <luca@coelho.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Sujith reports that my commit af61a165
("mac80211: add control port protocol TX control flag") broke ath9k
(aggregation). The reason is that I made minstrel_ht use the flag in
the TX status path, where it can have been overwritten by the driver.
Since we have no more space in info->flags, revert that part of the
change for now, until we can reshuffle the flags or so.
Reported-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

my earlier patch "mac80211: change IBSS channel state to chandef"
created a regression by ignoring the channel parameter in
__ieee80211_sta_join_ibss, which breaks IBSS channel selection. This
patch fixes this situation by using the right channel and adopting the
selected bandwidth mode.

Cc: stable@vger.kernel.org
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.

This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"

Cc: stable@vger.kernel.org # 3.10
Reported-by: NTom Gundersen <teg@jklm.no>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

IBSS needs to release the channel context when leaving
but I evidently missed that. Fix it.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to be able to (securely) keep connections alive after
the system was suspended for WoWLAN, we need some additional
APIs. We already have API (ieee80211_gtk_rekey_notify) to tell
wpa_supplicant about the new replay counter if GTK rekeying
was done by the device while the host was asleep, but that's
not sufficient.

If GTK rekeying wasn't done, we need to tell the host about
sequence counters for the GTK (and PTK regardless of rekeying)
that was used while asleep, add ieee80211_set_key_rx_seq() for
that.

If GTK rekeying was done, then we need to be able to disable
the old keys (with ieee80211_remove_key()) and allocate the
new GTK key(s) in mac80211 (with ieee80211_gtk_rekey_add()).

If protocol offload (e.g. ARP) is implemented, then also the
TX sequence counter for the PTK must be updated, using the new
ieee80211_set_key_tx_seq() function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel Switch will later require to generate beacons without setting
them immediately. Therefore split the presp generation in an own
function. Splitting the original very long function might be a good idea
anyway.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch decouples the power save processing from the frame decryption
by running the decrypt rx handler after sta_process. In the case where
the decryption failed for some reason, the stack used to not process
the PM and MOREDATA bits for that frame. The stack now always performs
power save processing regardless of the decryption result. That means that
encrypted data frames and NULLFUNC frames are now handled in the same way
regarding power save processing, making the stack more robust.
Signed-off-by: NJohan Almbladh <ja@anyfi.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In some cases mac80211 will scan before creating an IBSS
even if bssid and frequency have been forced by the user.
This is not needed and leads only to a delay in the IBSS
establishment phase.

Immediately create the cell if both bssid and frequency
(and fixed_freq is set) have been specified.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pass the wdev from cfg80211 on to the driver as the vif
if given and it's valid for the driver.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To allow drivers to implement per-interface testmode operations
more easily, pass a wdev pointer if any identification for one
was given from userspace. Clean up the code a bit while at it.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.

Also use the new flag in the iwlwifi drivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow lowest basic rate to be used for unicast management frame in
mesh. Otherwise, the lowest supported rate is used for unicast
management frame, such as 1Mbps for 2.4GHz and 6Mbps for 5GHz. Rename
the rc_send_low_broadcast to re_send_low_basicrate since now it is
also applied to unicast management frame in mesh.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A few places in the code (mac80211 and iwlmvm) use the same
TU_TO_JIFFIES() macro and could use TU_TO_EXP_TIME() that
mac80211 has. Make these available to everyone and use them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.

This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a per-station debugfs file indicating the TIDs (as
a bitmap) that the driver has data buffered on.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The radiotap VHT info is 12 bytes (required to be aligned on 2) :
u16 known - IEEE80211_RADIOTAP_VHT_KNOWN_*
u8 flags - IEEE80211_RADIOTAP_VHT_FLAG_*
u8 bandwidth
u8 mcs_nss[4]
u8 coding
u8 group_id
u16 partial_aid

ATM mac80211 can handle IEEE80211_RADIOTAP_VHT_KNOWN_{GI,BANDWIDTH} and
mcs_nss[0] (i.e single user) in simple cases.
This is more a placeholder to let sniffers give more clues for VHT,
since we don't have yet the proper infrastructure/conventions
in mac80211 for complete feedback (e.g consider dynamic BW).
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A station which is not authorized has to be purged earlier
to give it a chance to re-try to establish an IBSS/RSN
session soon. Set the timeout to 10 seconds.

Some refactoring has also been done to allow the IBSS
submodule to have its own expiring function.
Reported-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change mac80211 LED trigger code to use the generic
led_trigger_blink_oneshot() API for transmit and receive activity
indication.

This gives a better feedback to the user, as with the new API each
activity event results in a visible blink, while a constant traffic
results in a continuous blink at constant rate.
Signed-off-by: NFabio Baltieri <fabio.baltieri@gmail.com>
[fix LED disabled build error]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In case the AP has different regulatory information than we do,
it can happen that we connect to an AP based on e.g. the world
roaming regulatory data, and then update our database with the
AP's country information disables the channel the AP is using.
If this happens on an HT AP, the bandwidth tracking code will
hit the WARN_ON() and disconnect. Since that's not very useful,
ignore the channel-disable flag in bandwidth tracking.

Cc: stable@vger.kernel.org
Reported-by: NChris Wright <chrisw@sous-sol.org>
Tested-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

While we're connected, the AP shouldn't change the primary channel
in the HT information. We checked this, and dropped the connection
if it did change it.

Unfortunately, this is causing problems on some APs, e.g. on the
Netgear WRT610NL: the beacons seem to always contain a bad channel
and if we made a connection using a probe response (correct data)
we drop the connection immediately and can basically not connect
properly at all.

Work around this by ignoring the HT primary channel information in
beacons if we're already connected.

Also print out more verbose messages in the other situations to
help diagnose similar bugs quicker in the future.

Cc: stable@vger.kernel.org [3.10]
Acked-by: NAndy Isaacson <adi@hexapodia.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

TX status notification can get lost, or the frames could
get stuck on the queue, so don't wait for the callback
from the driver forever and instead time out after half
a second.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit "3d9646d0 mac80211: fix channel selection bug" introduced a possible
infinite loop by moving the out target above the chandef_downgrade
while loop.  When we downgrade to NL80211_CHAN_WIDTH_20_NOHT, we jump
back up to re-run the while loop...indefinitely.  Replace goto with
break and carry on.  This may not be sufficient to connect to the AP,
but will at least keep the cpu from livelocking.  Thanks to Derek Atkins
as an extra pair of debugging eyes.

Cc: stable@kernel.org
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

My commit:

commit 12e7f517
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Thu Feb 28 10:55:26 2013 +0100

    mac80211: cleanup generic suspend/resume procedures

removed check for deleting MONITOR and AP_VLAN when suspend. That can
cause a crash (i.e. in iwlagn_mac_remove_interface()) since we remove
interface in the driver that we did not add before.

Reference:
http://marc.info/?l=linux-kernel&m=137391815113860&w=2Bisected-by: NOrtwin Glück <odi@odi.ch>
Reported-and-tested-by: NOrtwin Glück <odi@odi.ch>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch is intended to avoid the buffering to non-assoc mesh STA
and also to avoid the triggering of frame to non-assoc mesh STA which
could cause kernel panic in specific hw.

One of the examples, is kernel panic happens to ath9k if user space
inserts the mesh STA and not proceed with the SAE and AMPE, and later
the same mesh STA is detected again. The sta_state of the mesh STA remains
at IEEE80211_STA_NONE and if the ieee80211_sta_ps_deliver_wakeup is called
and subsequently the ath_tx_aggr_wakeup, the kernel panic due to
ath_tx_node_init is not called before to initialize the require data
structures.

This issue is reported by Cedric Voncken before.
http://www.spinics.net/lists/linux-wireless/msg106342.html

[<831ea6b4>] ath_tx_aggr_wakeup+0x44/0xcc [ath9k]
[<83084214>] ieee80211_sta_ps_deliver_wakeup+0xb8/0x208 [mac80211]
[<830b9824>] ieee80211_mps_sta_status_update+0x94/0x108 [mac80211]
[<83099398>] ieee80211_sta_ps_transition+0xc94/0x34d8 [mac80211]
[<8022399c>] nf_iterate+0x98/0x104
[<8309bb60>] ieee80211_sta_ps_transition+0x345c/0x34d8 [mac80211]
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move
the assignment further down, after the rate_control_send_low call.
Reported-by: NKrzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>