Signed-off-by: NSuresh Sidda <suresh.b.siddha@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

it is a synonym for CONFIG_ACPI
Signed-off-by: NLen Brown <len.brown@intel.com>

it has been a synonym for CONFIG_ACPI since 2.6.12
Signed-off-by: NLen Brown <len.brown@intel.com>

The patch adds boundary check for the MAX_GSI_NUM.  Same as the update for
i386, the patch addresses a problem with ACPI SCI IRQ.  The patch corrects
the code such that SCI IRQ is skipped and duplicate entry is avoided.  The
VIA chipset uses 4-bit IRQ register for internal interrupt routing, and
therefore cannot handle IRQ numbers assigned to its devices.  The patch
corrects this problem by allowing PCI IRQs below 16.
Signed-off-by: NNatalie Protasevich <Natalie.Protasevich@unisys.com>
Acked-by: NAndi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Various code needs this information now before the actual SMP bootup.  Instead
of computing it on the fly while booting the other CPUs set it up now while
initial MPtable/MADT parsing.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I suggest to change the way IRQs are handed out to PCI devices.

Currently, each I/O APIC pin gets associated with an IRQ, no matter if the
pin is used or not.  It is expected that each pin can potentually be
engaged by a device inserted into the corresponding PCI slot.  However,
this imposes severe limitation on systems that have designs that employ
many I/O APICs, only utilizing couple lines of each, such as P64H2 chipset.

It is used in ES7000, and currently, there is no way to boot the system
with more that 9 I/O APICs.

The simple change below allows to boot a system with say 64 (or more) I/O
APICs, each providing 1 slot, which otherwise impossible because of the IRQ
gaps created for unused lines on each I/O APIC.  It does not resolve the
problem with number of devices that exceeds number of possible IRQs, but
eases up a tension for IRQs on any large system with potentually large
number of devices.

I only implemented this for the ACPI boot, since if the system is this big
and using newer chipsets it is probably (better be!) an ACPI based system
:).  The change is completely "mechanical" and does not alter any internal
structures or interrupt model/implementation.  The patch works for both
i386 and x86_64 archs.  It works with MSIs just fine, and should not
intervene with implementations like shared vectors, when they get worked
out and incorporated.

To illustrate, below is the interrupt distribution for 2-cell ES7000 with
20 I/O APICs, and an Ethernet card in the last slot, which should be eth1
and which was not configured because its IRQ exceeded allowable number (it
actially turned out huge - 480!):

zorro-tb2:~ # cat /proc/interrupts
           CPU0       CPU1       CPU2       CPU3       CPU4       CPU5       CPU6       CPU7
  0:      65716      30012      30007      30002      30009      30010      30010      30010    IO-APIC-edge  timer
  4:        373          0        725        280          0          0          0          0    IO-APIC-edge  serial
  8:          0          0          0          0          0          0          0          0    IO-APIC-edge  rtc
  9:          0          0          0          0          0          0          0          0   IO-APIC-level  acpi
 14:         39          3          0          0          0          0          0          0    IO-APIC-edge  ide0
 16:        108         13          0          0          0          0          0          0   IO-APIC-level  uhci_hcd:usb1
 18:          0          0          0          0          0          0          0          0   IO-APIC-level  uhci_hcd:usb3
 19:         15          0          0          0          0          0          0          0   IO-APIC-level  uhci_hcd:usb2
 23:          3          0          0          0          0          0          0          0   IO-APIC-level  ehci_hcd:usb4
 96:       4240        397         18          0          0          0          0          0   IO-APIC-level  aic7xxx
 97:         15          0          0          0          0          0          0          0   IO-APIC-level  aic7xxx
192:        847          0          0          0          0          0          0          0   IO-APIC-level  eth0
NMI:          0          0          0          0          0          0          0          0
LOC:     273423     274528     272829     274228     274092     273761     273827     273694
ERR:          7
MIS:          0

Even though the system doesn't have that many devices, some don't get
enabled only because of IRQ numbering model.

This is the IRQ picture after the patch was applied:

zorro-tb2:~ # cat /proc/interrupts
           CPU0       CPU1       CPU2       CPU3       CPU4       CPU5       CPU6       CPU7
  0:      44169      10004      10004      10001      10004      10003      10004       6135    IO-APIC-edge  timer
  4:        345          0          0          0          0        244          0          0    IO-APIC-edge  serial
  8:          0          0          0          0          0          0          0          0    IO-APIC-edge  rtc
  9:          0          0          0          0          0          0          0          0   IO-APIC-level  acpi
 14:         39          0          3          0          0          0          0          0    IO-APIC-edge  ide0
 17:       4425          0          9          0          0          0          0          0   IO-APIC-level  aic7xxx
 18:         15          0          0          0          0          0          0          0   IO-APIC-level  aic7xxx, uhci_hcd:usb3
 21:        231          0          0          0          0          0          0          0   IO-APIC-level  uhci_hcd:usb1
 22:         26          0          0          0          0          0          0          0   IO-APIC-level  uhci_hcd:usb2
 23:          3          0          0          0          0          0          0          0   IO-APIC-level  ehci_hcd:usb4
 24:        348          0          0          0          0          0          0          0   IO-APIC-level  eth0
 25:          6        192          0          0          0          0          0          0   IO-APIC-level  eth1
NMI:          0          0          0          0          0          0          0          0
LOC:     107981     107636     108899     108698     108489     108326     108331     108254
ERR:          7
MIS:          0

Not only we see the card in the last I/O APIC, but we are not even close to
using up available IRQs, since we didn't waste any.
Signed-off-by: NNatalie Protasevich <Natalie.Protasevich@unisys.com>
Acked-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Define pcibus_to_node to be able to figure out which NUMA node contains a
given PCI device.  This defines pcibus_to_node(bus) in
include/linux/topology.h and adjusts the macros for i386 and x86_64 that
already provided a way to determine the cpumask of a pci device.

x86_64 was changed to not build an array of cpumasks anymore.  Instead an
array of nodes is build which can be used to generate the cpumask via
node_to_cpumask.
Signed-off-by: NChristoph Lameter <christoph@lameter.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Suggested by Alexander Nyberg
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes the assumption that LAPIC entries contain the BSP as its
first entry.  This is a slight improvement to the temporary fix submitted by
Suresh Siddha.

- Removes assumption that LAPIC entries contain BSP first.

- Builds x86_acpiid_to_apicid[] and bios_cpu_apicid[] properly with BSP as
  first entry.

- Made maxcpus=1 boot on these systems.  Since the parsing earlier in
  arch/x86_64/kernel/mpparse.c stopped after maxcpus entries, other entries
  were not processed, this causes kernel not to boot on these systems.

TBD: x86_acpiid_to_apicid and bios_cpu_apicid[] seem to be exactly the
     same.  This could be removed, but might need more work to cleanup.
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It is unnecessary on modern Intel or AMD systems, and that is all we support
on x86-64

Also causes problems on various systems
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!