Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 16 12月, 2015 1 次提交
    • L
      irqchip/gic: Support RealView variant setup · 8673c1d7
      由 Linus Walleij 提交于 
      The ARM RealView PB11MPCore reference design has some special
bits in a system controller register to set up the GIC in one
of three modes: legacy, new with DCC, new without DCC. The
register is also used to enable FIQ.

Since the platform will not boot unless this register is set
up to "new with DCC" mode, we need a special quirk to be
compiled-in for the RealView platforms.

If we find the right compatible string on the GIC TestChip,
we enable this quirk by looking up the system controller and
enabling the special bits.

We depend on the CONFIG_REALVIEW_DT Kconfig symbol as the old
boardfile code has the same fix hardcoded, and this is only
needed for the attempts to modernize the RealView code using
device tree.

After fixing this, the PB11MPCore boots with device tree
only.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
      8673c1d7
  3. 14 10月, 2015 1 次提交
  5. 25 8月, 2015 1 次提交
  7. 21 8月, 2015 1 次提交
  9. 01 8月, 2015 1 次提交
  11. 30 7月, 2015 2 次提交
  13. 23 6月, 2015 1 次提交
  15. 22 6月, 2015 2 次提交
  17. 28 5月, 2015 1 次提交
  19. 01 4月, 2015 1 次提交
    • K
      IRQCHIP: Add new driver for BCM7038-style level 1 interrupt controllers · 5f7f0317
      由 Kevin Cernekee 提交于 
      This is the main peripheral IRQ controller on the BCM7xxx MIPS chips;
it has the following characteristics:

 - 64 to 160+ level IRQs
 - Atomic set/clear registers
 - Reasonably predictable register layout (N status words, then N
   mask status words, then N mask set words, then N mask clear words)
 - SMP affinity supported on most systems
 - Typically connected to MIPS IRQ 2,3,2,3 on CPUs 0,1,2,3

This driver registers one IRQ domain and one IRQ chip to cover all
instances of the block.  Up to 4 instances of the block may appear, as
it supports 4-way IRQ affinity on BCM7435.

The same block exists on the ARM BCM7xxx chips, but typically the ARM GIC
is used instead.  So this driver is primarily intended for MIPS STB chips.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8844/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
      5f7f0317
  21. 15 3月, 2015 1 次提交
  23. 08 3月, 2015 1 次提交
    • S
      irqchip: vf610-mscm-ir: Add support for Vybrid MSCM interrupt router · 0494e11a
      由 Stefan Agner 提交于 
      This adds support for Vybrid's interrupt router. On VF6xx models,
almost all peripherals can be used by either of the two CPU's,
the Cortex-A5 or the Cortex-M4. The interrupt router routes the
peripheral interrupts to the configured CPU.

This IRQ chip driver configures the interrupt router to route
the requested interrupt to the CPU the kernel is running on.
The driver makes use of the irqdomain hierarchy support. The
parent is given by the device tree. This should be one of the
two possible parents either ARM GIC or the ARM NVIC interrupt
controller. The latter is currently not yet supported.

Note that there is no resource control mechnism implemented to
avoid concurrent access of the same peripheral. The user needs
to make sure to use device trees which assign the peripherals
orthogonally. However, this driver warns the user in case the
interrupt is already configured for the other CPU. This provides
a poor man's resource controller.
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NStefan Agner <stefan@agner.ch>
Link: https://lkml.kernel.org/r/1425249689-32354-2-git-send-email-stefan@agner.chSigned-off-by: NJason Cooper <jason@lakedaemon.net>
      0494e11a
  25. 04 3月, 2015 1 次提交
  27. 26 1月, 2015 1 次提交
  29. 26 11月, 2014 3 次提交
  31. 24 11月, 2014 1 次提交
  33. 09 11月, 2014 1 次提交
  35. 17 9月, 2014 1 次提交
  37. 14 9月, 2014 1 次提交
  39. 20 8月, 2014 1 次提交
  41. 18 8月, 2014 1 次提交
  43. 17 7月, 2014 1 次提交
  45. 09 7月, 2014 2 次提交
  47. 01 7月, 2014 1 次提交
  49. 27 5月, 2014 1 次提交
  51. 26 3月, 2014 1 次提交
  53. 04 3月, 2014 1 次提交
  55. 01 3月, 2014 1 次提交
  57. 05 2月, 2014 1 次提交
    • S
      DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP · 96ca848e
      由 Sricharan R 提交于 
      Some socs have a large number of interrupts requests to service
the needs of its many peripherals and subsystems. All of the
interrupt lines from the subsystems are not needed at the same
time, so they have to be muxed to the irq-controller appropriately.
In such places a interrupt controllers are preceded by an CROSSBAR
that provides flexibility in muxing the device requests to the controller
inputs.

This driver takes care a allocating a free irq and then configuring the
crossbar IP as a part of the mpu's irqchip callbacks. crossbar_init should
be called right before the irqchip_init, so that it is setup to handle the
irqchip callbacks.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: NSricharan R <r.sricharan@ti.com>
Acked-by: Kumar Gala <galak@codeaurora.org> (for DT binding portion)
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
      96ca848e
  59. 23 1月, 2014 1 次提交
  61. 15 1月, 2014 2 次提交
  63. 13 12月, 2013 1 次提交
  65. 26 11月, 2013 1 次提交
  67. 24 8月, 2013 1 次提交