Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_s_jpegcomp.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A number of old drivers still had the experimental tag. Time to remove it.
It concerns the following drivers:
VIDEO_TLV320AIC23B
USB_STKWEBCAM
VIDEO_CX18
VIDEO_CX18_ALSA
VIDEO_ZORAN_AVS6EYES
DVB_USB_AF9005
MEDIA_TUNER_TEA5761
VIDEO_NOON010PC30
This decision was taken during the 2012 Media Workshop.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If start_streaming() fails (e.g. out of memory) the driver needs to
rewind the start procedure. This implies possibly stopping the device
and clearing the buffer queue.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The driver was expecting to get a valid pixelformat on s_fmt and try_fmt.
This is wrong, since the user may pass a bitmask and expect the driver
to change it, returning a valid (fourcc) pixelformat.
This problem was spotted by v4l2-compliance.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When an urb buffer can't be allocated, the currently allocated
buffer count must be saved so they can properly released.
Moreover, it's sufficient to call stk1160_free_isoc to have
all urb buffers released.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is just a cleaning patch to produce more useful
debug messages.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Plain '-1' is not very good error code. Use more suitable error
code definitions.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

... and some minor logging changes.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use .get_if_frequency() as all used tuner drivers
(mt2060/qt1010/mxl5005s) supports it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is not good idea to return error for missing callback
handler as whole callback as optional and could be missing
by intentionally.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is first step closer to support multiple tuners.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is RTL2832U + FC2580 reference design.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch add the toggle bit to the tt3650_rc_query function of the ttusb2
driver.
Signed-off-by: NJose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

commit da35de64 broke compilation, as it reverted the name of the
usb card free function.

Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If we fail to set up the capture device we go through negative indexes and
badness happens. Add the missing test.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44551Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It needs the e4000 tuner driver.
Signed-off-by: NPhilipp Dreimann <philipp@dreimann.net>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is not allowed to call usb_clear_halt() after urbs are submitted.
That causes oops sometimes. Move whole streaming_ctrl() logic to
power_ctrl() in order to avoid wrong usb_clear_halt() use. Also,
configuring streaming endpoint in streaming_ctrl() sounds like a
little bit wrong as it is aimed for control stream gate.
Reported-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since ifnum is not used anywhere it is safe to remove it.
This was spotted by Hans's media_tree daily build.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

struct vb2_queue is allocated through kzalloc as part of a larger struct,
there's no need to clear it.
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert drivers: au6610, ce6230, ec168, rtl28xxu for
dvb_usb_dbg_usb_control_msg() macro.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For dumping usb_control_msg().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

After qt1010 change that device seems to survive from reset resume.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is workaround / partial fix.

rtl2832u_power_ctrl() and rtl2832u_frontend_attach() needs to
be go through carefully and fix properly. There is clearly
some logical errors when handling power-management ang GPIOs...
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: Thomas Mair <thomas.mair86@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Stream did not start anymore after stream was stopped once.

Following error can be seen, xhci_hcd
WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.

usb_clear_halt for streaming endpoint helps.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It survives now on reset_resume.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The uvcvideo driver now supports USERPTR, and isn't limited to YUYV and
MJPEG anymore.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca_pac7302: avoid duplicate calls of the image quality adjustment functions on capturing start

There is no need to call the image quality adjustment functions in sd_start.
The gspca main driver calls v4l2_ctrl_handler_setup in gspca_init_transfer,
which already applies all image control values.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The current white balance temperature default value is 4, which is much too small (possible values are 0-255).
Improve the picture quality by increasing the default value to 55, which is the default value used by the Windows driver.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>