The addition of the AVF and virtchnl code to the i40evf driver
means we should update the i40evf.txt file with the most up to date
information.

It seems this file hasn't been updated in a while, so the
changes cover a little more than just AVF, but it's all only
in the i40evf.txt.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add device ID define and mac_type assignment needed for
Adaptive Virtual Function (VF Base Mode Support).

Also, update version to v3.0.0 in order to indicate
clearly that this is the first driver supporting the AVF
device ID.
Signed-off-by: NPreethi Banala <preethi.banala@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This uses preprocessor tricks to make sure that a divide by zero
occurs if a struct changes size outside the expected number of
bytes.
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This removes holes and makes structure sizes consistent across
32 and 64 bit builds.
Signed-off-by: NSridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This moves a function that is needed for the virtchnl interface
from the i40e PF driver over to the virtchnl.h file.

It was manually verified that the function in question is unchanged
except for the function name and function header, which explains
the slight difference in the number of lines removed/added.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements the complete version of the virtchnl.h file
with final renames, and fixes the related code in i40e and i40evf.

It also expands comments, and adds details on the usage of
certain fields.

In addition, due to the changes a couple of casts are needed
to prevent errors found by sparse after renaming some fields.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes up a bunch of whitespace issues introduced
by the previous automated change of name from i40e to virtchnl.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updates the arguments passed to the validate function
and fixes the caller, as well as uses the new return values added to
virtchnl.h

One other minor tweak, remove a duplicate set to zero of valid_len.

This is in preparation for moving the function to virtchnl.h.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As part of the conversion, change the arguments
to VF_IS_V1[01] macros and move them to virtchnl.h
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Before moving this function over to virtchnl.h, move
some driver specific checks that had snuck into a fairly
generic function, back into the caller of the function.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This morphs all the i40e and i40evf references to/in virtchnl.h
to be generic, using only automated methods. Updates all the
callers to use the new names.  A followup patch provides separate
clean ups for messy line conversions from these "automatic"
changes, to make them more reviewable.

Was executed with the following sed script:
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_client.c
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_prototype.h
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
sed -i -f transform_script drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40e_common.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40e_prototype.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf.h
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_client.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_main.c
sed -i -f transform_script drivers/net/ethernet/intel/i40evf/i40evf_virtchnl.c
sed -i -f transform_script include/linux/avf/virtchnl.h

transform_script:
----8<----
s/I40E_VIRTCHNL_SUPPORTED_QTYPES/SAVE_ME_SUPPORTED_QTYPES/g
s/I40E_VIRTCHNL_VF_CAP/SAVE_ME_VF_CAP/g

s/I40E_VIRTCHNL_/VIRTCHNL_/g
s/i40e_virtchnl_/virtchnl_/g
s/i40e_vfr_/virtchnl_vfr_/g
s/I40E_VFR_/VIRTCHNL_VFR_/g

s/VIRTCHNL_OP_ADD_ETHER_ADDRESS/VIRTCHNL_OP_ADD_ETH_ADDR/g
s/VIRTCHNL_OP_DEL_ETHER_ADDRESS/VIRTCHNL_OP_DEL_ETH_ADDR/g
s/VIRTCHNL_OP_FCOE/VIRTCHNL_OP_RSVD/g

s/SAVE_ME_SUPPORTED_QTYPES/I40E_VIRTCHNL_SUPPORTED_QTYPES/g
s/SAVE_ME_VF_CAP/I40E_VIRTCHNL_VF_CAP/g
----8<----
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the i40e driver to start using the new virtchnl
interface header file, and removes an already existing duplicate of the
i40e_virtchnl.h file contained in the i40e directory.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This moves a header for i40evf to include/linux/avf/virtchnl.h.
The directory name AVF is an acronym for the Intel(R) Adaptive
Virtual Function.

This first step creates the new file, which is a rename of
drivers/net/ethernet/intel/i40evf/i40e_virtchnl.h to
include/linux/avf/virtchnl.h, and should show up in git
as a rename when using git log --follow.

To keep things building after the move, the changes to the i40evf
driver are made to point to the new include file location.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This drops the i40e_type.h include in anticipation of the next
patch which moves this file to a location where type.h doesn't
exist, and all the places this file is included already include
i40e_type.h before this file.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When BRIDGE is a loadable module, MLXSW_SPECTRUM mustn't be built-in:

drivers/built-in.o: In function `mlxsw_sp_bridge_device_create':
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:145: undefined reference to `br_vlan_enabled'
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:158: undefined reference to `br_multicast_enabled'
drivers/built-in.o: In function `mlxsw_sp_dev_rif_type':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:2972: undefined reference to `br_vlan_enabled'
drivers/built-in.o: In function `mlxsw_sp_inetaddr_vlan_event':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:3310: undefined reference to `br_vlan_enabled'

Add Kconfig dependency to enforce usable configurations.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Corentin Labbe says:

====================
net-next: stmmac: add dwmac-sun8i ethernet driver

This patch series add the driver for dwmac-sun8i which handle the Ethernet MAC
present on Allwinner H3/H5/A83T/A64 SoCs.

This driver is the continuation of the sun8i-emac driver.
During the development, it appeared that in fact the hardware was a modified
version of some dwmac.
So the driver is now written as a glue driver for stmmac.

It supports 10/100/1000 Mbit/s speed with half/full duplex.
It can use an internal PHY (MII 10/100) or an external PHY
via RGMII/RMII.

This patch series enable the driver only for the H3/A64/H5 SoC since A83T
doesn't have the necessary clocks present in mainline.

The driver have been tested on the following boards:
- H3 Orange PI PC, BananaPI-M2+
- A64 Pine64, BananaPi-M64
- A83T BananaPI-M3

The first two patchs are some mandatory changes for letting dwmac-sun8i be used.
The following three patchs add the driver and its documentation.
The remaining are DT patch enabling it.

Regards
Corentin Labbe

Changes since v5:
- Added DT patch for NanoPi neo
- Use the new adjust_link variables (speedxxx/speedmask)
- Made the timeout of readl_poll_timeout from 10 to 100ms
- Fix sun8i_unpower_phy that could be called twice
- Replace phy by phy-handle in doc/dwmac-sun8i.txt

Changes since v4:
- Re-ordered by alphabetical order some DT nodes
- Simplified power/unpower_phy functions by testing the use of internal_phy
- Added a patch for adding dwmac-sun8i to arm64 defconfig
- Fix a typo in sun50i-a64-system-controller (wrongly used sun8i)
- Reworked uc/mc filter address setting

Changes since v3:
- Renamed tx-delay/rx-delay to tx-delay-ps/rx-delay-ps
- fix syscon compatible example
- Changed parameter type for setup() function
- Dropped some DT patchs for boards which I could not test further

Changes since v2:
- corrected order of syscon compatible
- added compatible = "ethernet-phy-ieee802.3-c22 to PHY
- added set_mac function

Changes since v1:
- added TX/RX delay units
- splitted syscon documentation in its own patch
- regulator is now disabled after clk_prepare_enable(gmac->tx_clk) error
- Fixed a memory leak on mac_device_info
- Use now generic pin config for all DT stuff
- CONFIG_DWMAC_SUN8I is now set to y in defconfigs
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the dwmac-sun8i ethernet driver as a module in the ARM64 defconfig.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the dwmac-sun8i driver in the multi_v7 default configuration
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the dwmac-sun8i driver in the sunxi default configuration
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i  hardware is present on the BananaPi M64.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the pine64 plus.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the pine64
It uses an external PHY via RMII.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the dt node for the syscon register present on the
Allwinner A64.

Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the NanoPi Neo.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Orange Pi PC Plus, the polarity of the LEDs on the RJ45 Ethernet
port were changed from active low to active high.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI 2.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI One.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI Zero.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI PC.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000
speed.

This patch enable the dwmac-sun8i on Allwinner H3/H5 SoC Device-tree.
SoC H3/H5 have an internal PHY, so optionals syscon and ephy are set.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the dt node for the syscon register present on the
Allwinner H3/H5

Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock..
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds documentation for Device-Tree bindings for the
syscon present in allwinner devices.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds documentation for Device-Tree bindings for the
Allwinner dwmac-sun8i driver.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of adding more ifthen logic for adding a new mac_device_info
setup function, it is easier to add a function pointer to the function
needed.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thoses symbol will be needed for the dwmac-sun8i ethernet driver.
For letting it to be build as module, they need to be exported.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

asm-generic/socket.h already has an exception for the differences that
powerpc needs, so just include it after defining the differences.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add callback to the ethtool flash_device op. This callback uses the mlxfw
module to flash the new firmware file to the device.

As the firmware flash process takes about 20 seconds and ethtool takes the
rtnl lock during the flash_device callback, release the rtnl lock at the
beginning of the flash process and take it again before leaving the
callback. This way, the rtnl is not held during the process. To make sure
the device does not get deleted during the flash process, take a reference
to it before releasing the rtnl lock.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: Status block changes

The device maintains a CAM mapping of the internal status blocks
and the various PF/VF MSI-x vector mappings.
During initialization, the driver reads the HW memory and constructs
a shadow SW implementation which it would later use for manipulation
of interrupts. E.g., when enabling VFs and setting their MSI-x tables.

The driver currently has some very strict assumptions on the order the
entries are placed in the CAM. Specifically, it assumes that all entries
belonging to a PF would be consecutive and in-order in the CAM, and that
the VF entries would then follow. But there's no actual HW constraint
enforcing this assumption [although management firmware does set it
accordingly to same assumption initially].

Since the CAM is re-configurable, there are now SW flows employeed
by other OSes that might cause the assumption to be invalid.
Such flows allow the PF to forfeit some of it's available interrupts
in favor of its VFs or vice versa.
While those are not employeed today by qed, we want to relax the
assumptions as much as we can -
both to allow functionality after PDA as well as allowing future
compatibility where the driver would be loaded after a newer one has
'dirtied' the CAM configuration.

In addition to patches meant for the above relaxation, the series
also contains various cleanups & refactoring for interrupt logic
[most of which is !semantic].
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>