- Add in a new case for volume offline. Resolves internal testing bug
   for multilun array management.
 - Return correct status for failed TURs.
Reviewed-by: NScott Benesh <scott.benesh@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

- Setting coalescing has a significant negative impact on low
  queue-depth performance.
- Does not help high queue-depth performance.
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NScott Benesh <scott.benesh@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This can be used to check for fs vs non-fs requests and basically
removes all knowledge of BLOCK_PC specific from the block layer,
as well as preparing for removing the cmd_type field in struct request.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch cleanup warning reported by checkpatch.pl WARNING: Possible
unnecessary 'out of memory' message With no available memory, a warn on
message already gets printed by page alloc apis and modified goto use if
memory unallocated.
Signed-off-by: NAmit Kushwaha <kushwaha.a@samsung.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Older SmartArray controllers (eg SmartArray 64xx) do not support the
extended REPORT PHYS command, so fallback to use the legacy version
here.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Passing one instead of 8 or 16 arguments reduces the size of the
generated code somewhat:

add/remove: 2/3 grow/shrink: 1/4 up/down: 1772/-2137 (-365)

There's one more candidate, unique_id_show, but that uses %02X, and I'm
not sure it would be ok to start using lowercase there, so I've left it
alone for now.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add a sysfs attribute 'ctlr_num' holding the current HPSA controller
number. This is required to construct compability 'cciss' links.

[mkp: fixed typo]
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

NOT_READY is a sense key, not a legit scsi hostbyte value. Use
DID_NO_CONNECT instead.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Older controllers use SCSI target id '0' for the first internal disk. As
the controllers are now placed on the same bus as the internal disks
this leads to a clash with the SCSI target id of controller.  This patch
checks the SCSI revision, and moves older controller to bus '3' to be
compatible with older releases and avoid this problem.

[mkp: fixed uninitialized variable]

Fixes: 09371d62 ("hpsa: Change SAS transport devices to bus 0.")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: NHannes Reinecke <hare@suse.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

- driver was not calling done in some cases which causes the volume to
  be offlined.
- avoid doing rescan during a reset.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use correct index on q, use h->intr_mode instead of i. Issue detected
using static analysis with cppcheck

Fixes: bc2bb154 ("scsi: hpsa: use pci_alloc_irq_vectors and automatic irq affinity")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch converts over hpsa to use the pci_alloc_irq_vectors including
the PCI_IRQ_AFFINITY flag that automatically assigns spread out irq
affinity to the I/O queues.

It also cleans up the per-ctrl interrupt state due to the use of the
pci_irq_vector and pci_free_irq_vectors helpers that don't need to know
the exact irq type.  Additionally it changes a little oddity in the
existing code that was using different array indixes into the per-vector
arrays depending on whether a controller is using a single INTx or
single MSI irq.

[mkp: fixed typo]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NDon Brace <don.brace@microsemi.com>
Tested-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It's not necessary to cast the result of kmalloc, since void pointers
are promoted to any other type. This also fixes following coccinelle
warning:

casting value returned by memory allocation function to (BIG_IOCTL_Command_struct *) is useless.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

calling fill_cmd() using a MACRO definition not handled in switch
statement causes BUG() to be called.
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Missing 5 bits of byte 1 in the LBA issued by SML.
Reported-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NScott Benesh <scott.benest@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NScott Benesh <scott.benest@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Before using vendor-specific VPD pages for getting raid_level and
device_id, check for page support.  If page isn't supported, don't try
to use it.  Also, pay attention to return status on hpsa_get_device_id.

[mkp: fix boolean return warnings reported by kbuild test robot]
Reviewed-by: NScott Benesh <scott.benest@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

A device can be deleted causing NULL pointer issues.
Reviewed-by: NScott Benesh <scott.benesh@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently we are checking for external status before we are determining
if a device is an external device.
Reviewed-by: NScott Benesh <scott.benest@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Was not alloting for FW Flash times.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The SA controller spins down RAID drive spares.

A REGNEWD event causes an inquiry to be sent to all physical
drives. This causes the SA controller to spin up the spare.

The controller suspends all I/O to a logical volume until
the spare is spun up. The spin-up can take over 50 seconds.

This can result in one or both of the following:
 - SML sends down aborts and resets to the logical volume
   and can cause the logical volume to be off-lined.
 - a negative impact on the logical volume's I/O performance
   each time a REGNEWD is triggered.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The device ID obtained from the inquiry can only be of a single type.
The original code places a check for TYPE_ZBC right after the check for
TYPE_DISK. Logically, if the first if statement sees a device of a
TYPE_DISK and moves on to the second statement checking if not TYPE_ZBC,
it will always hit the continue.

[mkp: Applied by hand]
Signed-off-by: NPetros Koutoupis <petros@petroskoutoupis.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NGerry Morong <gerry.morong@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Need to report HBA device removal faster than the
event handler polling interval.

Stop I/O to the removed disk and wait for all
I/O operations to flush before removing the device.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

set offload_to_be_enabled to 0 when an ioaccel2 error is processed.

Before, an ioaccel completion error would turn of ioaccel but a rescan
would turn it back on again.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

offload_to_be_enabled also needs to be set to 0 during a state
change.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

faulty drives can cause the driver to hang during a
scan operation.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There have been companies requesting a sysfs entry
to obtain the sas address of device.
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver was calling scsi_scan_host before enabling interrupts.

This has gone unnoticed except for customers running in intx mode.
Calling scsi_scan_host before interrupts are enabled causes
"irq XX: nobody cared" messages and the driver to hang.

This patch enables interrupts before the call to scsi_scan_host.
Reported-by: NPiotr Karbowski <piotr.karbowski@gmail.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This has only called from show_sas_rphy_enclosure_identifier().  The
caller expects that we set an identifier, otherwise it uses an
uninitialized variable.

[mkp: fixed typo]
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch depends on patch
 - commit ac10a3e4ed64
   ("Export function scsi_scan.c:sanitize_inquiry_string")
Suggested-by: NHannes Reinecke <hare@suse.de>
Suggested-by: Matthew R. Ochs mrochs@linux.vnet.ibm.com
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

An oops can occur when submitting ioaccel2 commands when the phys_disk
pointer is NULL in hpsa_scsi_ioaccel_raid_map.  Happens when there are
configuration changes during I/O operations.

If the phys_disk pointer is NULL, send the command down the RAID path.
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Aborts were not being sent down to HBA devices
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Stop annoying "Error, could not get enclosure information"
messages.
Reviewed-by: NMahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
Reviewed-by: NJustin Lindley <justin.lindley@microsemi.com>
Reviewed-by: NScott Teel <scott.teel@microsemi.com>
Reviewed-by: NKevin Barnett <kevin.barnett@microsemi.com>
Reviewed-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Adding a new method to display enclosure device information.
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Left off some changes from Rasmus Villemoes where he changed snprintf to
scnprintf.
Suggested-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NJustin Lindley <justin.lindley@pmcs.com>
Reviewed-by: NKevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

HPSA_DIAG_OPTS_DISABLE_RLD_CACHING is a mask and bitwise AND was
intended here instead of logical &&.  This bug is essentially harmless,
it means that sometimes we don't print a warning message which we wanted
to print.

Fixes: c2adae44 ('hpsa: disable report lun data caching')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>