The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: NAndrew Paprocki <andrew@ishiboo.com>
Tested-by: NJohn Gumb <john.gumb@tandberg.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The atxp1 device detection code has a major logic flaw, fix it. Not
sure how we managed to miss this when the driver was merged...
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NSebastian Witt <se.witt@gmx.net>

Not all AMD K8 have 6 VID pins, contrary to what was assumed in
commit 116d0486. This commit broke
support of older CPU models which have only 5 VID pins:
http://bugzilla.kernel.org/show_bug.cgi?id=11329

We need two entries in the hwmon-vid table, one for 5-bit VID models
(K8 revision <= E) and one for 6-bit VID models (K8 revision >= F).
This fixes bug #11329.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NFrank Myhr <fmyhr@fhmtech.com>
Tested-by: NJean-Luc Coulon <jean.luc.coulon@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add in the CPUID for Nehalem chips.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Kent Liu <kent.liu@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, all sensors are read when the energy meter is queried via
sysfs.  This introduces a considerable amount of delay and variation in
the sysfs reading, which is not desirable when trying to profile energy
use.  Therefore, read only the energy meters when a sysfs query comes in
for them, and don't cache the results so that we always get the latest
reading.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On older machines, probing for a nonexistent AEM interface returned an
IPMI error; when we saw this, we'd stop probing.  On the x3650 M2 and
(presumably) later, we are returned a value indicating success and a
buffer full of garbage or zeroes.  This causes the probe function to run
in an infinite loop.  To fix this, we add one last check--if the
interface number we're looking for is higher than the number of
interfaces that AEM claims to have, stop probing.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previously the driver was only using DMI to prevent smbus probing on
non-Abit motherboards.  However, since the manual probing method is
brittle and prone to failure on some Abit motherboards (esp.  the Abit
IP35 Pro) it is better to use DMI to also read the board name and then
decide whether or not to probe the bus.

At the moment, we do not have a list of valid DMI name strings to use
for existing and supported motherboards.  This patch only implements DMI
probing for the IP35 Pro.  For motherboards that can not yet use DMI
probing, a warning will be printed to the kernel log asking those users
to email me their dmidecode output.

The existing manual probing mechanism will be used if CONFIG_DMI is not
enabled, if DMI probing fails (for DMI-unsupported motherboards), or if
DMI probing fails and the "force" option is set (for DMI-supported
motherboards).  Ideally in the longer term this manual probing method
would be removed.

This patch should be safe to apply as it does not change the probing
behaviour for most of the supported motherboards, just the IP35 Pro,
which already has regressions filed against it in 2.6.26.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11212Signed-off-by: NAlistair John Strachan <alistair@devzero.co.uk>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Export the sensor -> channel/dimm mapping in tempX_label.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...

Code for 8 channels by Tobias Himmer.

This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:

 * bb  is the resolution in number of bits (8, 10, 12)
 * c   is the number of channels (1, 2, 4, 8)
 * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
   kSPS and 101 for 1 MSPS)

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/hwmon/w83791d.c: In function `w83791d_probe':
drivers/hwmon/w83791d.c:1049: warning: unused variable `val1'
Signed-off-by: NMichael Borisov <niro@tut.by>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for Macbook v3 (sensors and accelerometer).
Signed-off-by: NNicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds support for fans and temperature sensors on intel iMac.

Tested on iMac 24" 2.8ghz (iMac8,1), it supports the following sensors:

cpu A
ambient
gpu
gpu diode
gpu heatsink
hd bay 1
memory controller
optical drive
power
Signed-off-by: NRoberto De Ioris <roberto@unbit.it>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Drop the legacy lm75 driver, and add a detect callback to the
new-style driver to achieve the same functionality.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>

The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: NAndrew Paprocki <andrew@ishiboo.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: NAndrew Paprocki <andrew@ishiboo.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

AMD NPT 0Fh cpus use 6 bit VID codes. Successive codes with msb 0
describe 25mV decrements, while those with msb 1 describe 12.5mV
decrements. Existing hwmon-vid.c is correct only for codes with msb 0;
add support for the codes with msb 1.

Ref:
p 309, Table 71
AMD Publication 32559, BIOS and Kernel Developer's Guide for AMD NPT Family 0Fh Processors
http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdfSigned-off-by: NFrank Myhr <fmyhr@fhmtech.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NFrank Myhr <fmyhr@fhmtech.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Driver for the Analog Devices AD7414 temperature monitoring chip.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add critical temperature limits to the driver. These limits are read
only.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The adm9240 driver is in the kernel for three years now, time to
remove the EXPERIMENTAL dependency.
Signed-off-by: NGrant Coady <gcoady.lk@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.

The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDominik Geyer <dominik.geyer@gmx.de>

Adds support for pwm_enable sysfs interface for the w83627hf driver.
Signed-off-by: NDominik Geyer <dominik.geyer@gmx.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128, 
and fixes a problem with incorrectly reported fan speeds. 
Signed-off-by: NMarc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

These functions aren't used before being defined, so there's no point
in forward-declaring them.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHans de Goede <j.w.r.degoede@hhs.nl>

Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
  and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: NJuerg Haefliger <juergh@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Skip the checking of the device ID register in the hwmon register
block if the force_id option is used.
Signed-off-by: NJuerg Haefliger <juergh@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Fix names of attribute structs to make them more consistent with the 
rest of the code. Minor comment changes.

Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Clean up and simplify the device initialization function:
* Degrade error messages to warnings - what they really are.
* Stop warning about VxI mode, we don't really care.
* Drop comment about lack of limit initialization - that's the standard
  way, all hardware monitoring drivers do that.
* Only read the configuration register once.
* Only write back to the configuration register if needed.
* Don't attempt to clear the lock bit, it locks itself to 1.
* Move the function to before it's called, so that we no longer need to
  forware declare it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Misc cleanups to the lm85 hardware monitoring driver:
* Mark constant arrays as const.
* Remove useless masks.
* Have lm85_write_value return void - nobody is checking the returned
  value anyway and in some cases it was plain wrong.
* Remove useless initializations.
* Rename new_client to client in lm85_detect.
* Replace cascaded if/else with a switch/case in lm85_detect.
* Group similar loops in lm85_update_device.
* Remove legacy comments.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

In set_pwm_auto_pwm_minctl, we write cached register bits back to the
chip. This is a bad idea as we have no guarantee that the cache is
up-to-date. Better read a fresh register value from the chip, it's
safer and in fact it is also more simple.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Fix most style issues reported by checkpatch, including:
* Trailing, missing and extra whitespace
* Extra parentheses, curly braces and semi-colons
* Broken indentation
* Lines too long

I verified that the generated code is the same before and after
these changes.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

More LM75 updates:

 - Teach the LM75 driver to use new-style driver binding:

     * Create a second driver struct, using new-style driver binding
       methods cribbed from the legacy code.

     * Add a MODULE_DEVICE_TABLE (for "newER-style binding")

     * The legacy probe logic delegates its work to this new code.

     * The legacy driver now uses the name "lm75_legacy".

 - More careful initialization.  Chips are put into 9-bit mode so
   the current interconversion routines will never fail.

 - Save the original chip configuration, and restore it on exit.
   (Among other things, this normally turns off the mode where
   the chip is constantly sampling ... and thus saves power.)

So the new-style code should catch all chips that boards declare,
while the legacy code catches others.  This particular coexistence
strategy may need some work yet ... legacy modes might best be set
up explicitly by some tool not unlike "sensors-detect".  (Or else
completely eradicated...)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Minor cleanup and reorg of the lm75 code.

 - Kconfig provides a larger list of lm75-compatible chips

 - A top comment now says what the driver does (!) ... as in, just
   what sort of sensor is this??

 - Section comments now delineate the various sections of the driver:
   hwmon attributes, driver binding, register access, module glue.
   One driver binding function moved out of the attribute section,
   as did the driver struct itself.

 - Minor tweaks to legacy probe logic:  correct a comment, and
   remove a pointless variable.

 - Whitespace, linelength, and comment fixes.

This patch should include no functional changes.  It's preparation
for adding new-style (driver model) I2C driver binding.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NLaurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

All the *_MAX_ADDR defines are never used, so remove them. The number
of registers of each type is already expressed by the *_COUNT defines.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch fixes a voltage scaling issue for the sch311x device.

Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.

Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch gets rid of a couple of macros previously used for sysfs attribute
generation and manipulation. This makes the source a little bigger but a lot
more readable and maintainable. It also fixes an issue with pwm5 & pwm6
attributes not being created read-only initially.

Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>