This update the register initialization/reset values (aka initvals)
for ar9271 based on the last recommended values on 2009-06-04 by our
systems engineering team.

The changes account for:

  * Supporting ar9271 1.0 and ar9271 1.1 together, the difference
    is bb_spectral_scan_ena, for 1.0 we'll set this to 0x1.

  * Ensuring we get the correct noise floor values -115 ~ -118
    when we enable bb_enable_ant_div_lnadiv=0 and
    mc_tx_def_ant_sel=1. Previous to this we would get noise
    floor values in the range -50 ~ -80. To fix settings for
    the registers:

     - bb_ch1_xatten1_db
     - bb_ch1_xatten2_db
     - bb_ch1_xatten1_margin
     - bb_ch1_xatten2_margin
     - bb_ch1_gain_force
     - bb_ch1_xatten2_hyst_margin
     - bb_ch1_xatten1_hyst_margin
     - bb_ch1_max_oc_gain

  * 0x8120[2] mc_mic_new_location_enable is changed to 0x1. The MAC team
    suggest to set this value.

  * 0x9910[0] bb_spectral_scan_ena is changed to 0x0.
    For ar9271 1.1 we don't need to enable this bit.

Cc: Stephen Chen <Stephen.Chen@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the WLAN_PRE80211 drivers moved to drivers/staging, this
distinction becomes unnecessary.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An extra register was being written to for PA calibration
making the hardware unresponsive, remove it. Hardware
reset should now complete fine on ar9271.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We had 0x9912 but AR_PHY_SPECTRAL_SCAN is 0x9910. By using the
0x9912 we were making the hardware unresponsive. This allows us
to move forward with hardware reset on ar9271 on the ath9k_htc
driver.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Devices with external radios have revisions which we can count on.
On single chip solutions these EEPROM values for these radio revision
also exist but are not meaningful as the radios are embedded onto the
same chip. Each single-chip device evolves together as one device.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These are shared between ath9k and the future ath9k_htc driver.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When TX is hung, the chip is reset. Ensure that
the chip is awake by using the PS wrappers.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PA calibration for ar9271 ath9k_hw_9271_pa_cal() can run during
reset or initial calibration, update the PA calibration to account
for that and initialize PA calibration variables for both conditions.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is required for the ar9271 hardware as well.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: sujith.manoharan@atheros.com
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

And move it to hw code on mac.c where it belongs.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This should fix the oops which occurs during module unload
due to the dereferencig of ah upon debugfs exit.

IP: [<46412d6b>] 0x46412d6b
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
last sysfs file: /sys/class/power_supply/BAT0/energy_full
Modules linked in: ath9k(-) ath9k_hw mac80211 ath cfg80211 <bleh>

Pid: 3112, comm: rmmod Not tainted (2.6.32-rc2-wl #101) 9461DUU
EIP: 0060:[<46412d6b>] EFLAGS: 00010246 CPU: 0
EIP is at 0x46412d6b
EAX: f5870004 EBX: f6700d94 ECX: 00000000 EDX: c14313a7
ESI: f5870000 EDI: fb58ce70 EBP: f6661eb4 ESP: f6661ea8
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process rmmod (pid: 3112, ti=f6660000 task=f6579380 task.ti=f6660000)
Stack:
fb57e5e5 f5ca5d50 fb58ce70 f6661ebc fb58629a f6661ec8 c11b715e f5ca5da8
<0> f6661ed8 c1223d98 f5ca5da8 f5ca5ddc f6661eec c1223e6f fb58ce70 fb58ce70
<0> c14958a0 f6661f00 c1222edb fb58ce70 fb58ce70 fb58cebc f6661f1c c12243c9
Call Trace:
[<fb57e5e5>] ? ath_cleanup+0x35/0x50 [ath9k]
[<fb58629a>] ? ath_pci_remove+0x1a/0x20 [ath9k]
[<c11b715e>] ? pci_device_remove+0x1e/0x40
[<c1223d98>] ? __device_release_driver+0x58/0xa0
[<c1223e6f>] ? driver_detach+0x8f/0xa0
[<c1222edb>] ? bus_remove_driver+0x7b/0xb0
[<c12243c9>] ? driver_unregister+0x49/0x80
[<c1158cf2>] ? sysfs_remove_file+0x12/0x20
[<c11b73b5>] ? pci_unregister_driver+0x35/0x90
[<fb586172>] ? ath_pci_exit+0x12/0x20 [ath9k]
[<fb5883ec>] ? ath9k_exit+0x10/0x3d [ath9k]
[<c131971d>] ? mutex_unlock+0xd/0x10
[<c1088c0f>] ? sys_delete_module+0x16f/0x220
[<c10e3d5d>] ? do_munmap+0x23d/0x290
[<c11a629c>] ? trace_hardirqs_off_thunk+0xc/0x10
[<c11a628c>] ? trace_hardirqs_on_thunk+0xc/0x10
[<c1003b41>] ? sysenter_exit+0xf/0x1a
[<c1003b08>] ? sysenter_do_call+0x12/0x3c
Code:  Bad EIP value.
EIP: [<46412d6b>] 0x46412d6b SS:ESP 0068:f6661ea8
CR2: 0000000046412d6b
---[ end trace 847f3b05ff3dcb19 ]---
Reported-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The core driver needs to be stopped and then as a last step the
hardware needs to be stopped and its structure free'd. We do this
by moving the core driver cleanup to a new helper ath_clean_core()
and have ath_cleanup() call it. Only as a last step does
ath_cleanup() now free the hw.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used in several places, ensure we do it right in all
callers by using a helper.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

debugfs uses the hardware for several debugfs files as such the
hardware must be initialized and available prior to its usage. The
same applies to when we free the hw structs -- free debufs file
entries prior to free'ing the hardware.
Reported-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

What this means is we can enable now debug prints without
requiring CONFIG_ATH9K_DEBUG.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hw code should never use private driver data, but
sometimes we need a backpointer so just stuff it on
the common ath struct.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows for hw support to be enabled for ar9271.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hw code for Atheros 802.11n hardware is commmon between
different chipsets. This moves this code into a separate
module, the next expected user of this code will be
the ath9k_htc module.

The ath9k/ dir is now selected by ATH9K_HW, an option which
gets selected by either ath9k or ath9k_htc, but remains
invisible for user menuconfig configuration. If either
ath9k or ath9k_htc will be compiled into the kernel
ath9k_hw will also be compiled in.

Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PCI and debug code will not be shared between ath9k and
ath9k_htc, so make that code use the common read/write ops.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Get power table offset from the EEPROM instead of using
  a hardcoded value of -5 if the EEPROM rev is >= 21.
* Add support in the 4k eeprom code for tx power offset
  in case we have a 4k AR9280 implementation.
* Fix tx power accuracy at high powers.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This has to be done if the EEPROM supports FCC Midband
capability.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reduce PLL Settle time and eliminate redundant PLL calls. Also reduce
the LoadNF timeout from 10 msec to 250usec as the 10 msec timeout was
hit with AR9285 in some cases.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clearing a local variable is unnecessary.
Get rid of it.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Move 0xa274 and 0xa27c to the top of tx_gain table.
* Update initvals to fix random failure of noise floor calibration.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For AR5416 chipsets, clearing RTC_RESET_EN when setting
the chip to SLEEP mode results in high power consumption.
This patch fixes this issue by not clearing it for AR5416.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the current channel is between 2412 and 2472 MHz and if the channel is
changing to 2484 MHz, then the registers 0xa1f4, 0xa1f8 and 0xa1fc need to be
programmed to the "japan_2484" values.  Conversely, if the current channel
is 2484 MHz and if the channel is changing to one between 2412 and 2472 MHz, then
the three registers need to be programmed to the "normal" values.

This is needed for compliance with Japanese regulatory requirements.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Prevent divide-by-zero errors in IQ Calibration.
* Do not run temperature compensation if initPDADC or currPDADC is zero.
* Also, introduce a separate function for handling OLC for AR9287.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As noted by Jiri.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is the last part to make ath9k hw code core driver agnostic.
I believe ath9k_htc can now use use the hw code unmodified.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac.c is now core driver independent.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hw code will be shared between ath9k and ath9k_htc.
Just a few more files are left to clean up, mark them as well.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used by hw code.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used just to determine how to program the MAC,
either for 20 MHz operation of 40 MHz so just use conf_is_ht40()
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>