drivers/net/wireless/mwifiex/pcie.c:204:12: warning:
  'mwifiex_pcie_resume' defined but not used [-Wunused-function]
drivers/net/wireless/mwifiex/pcie.c:166:12: warning:
  'mwifiex_pcie_suspend' defined but not used [-Wunused-function]

The suspend/resume handlers ought to be under CONFIG_PM directive.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

move functions up just to avoid static forward declaration for
mwifiex_pcie_resume.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

HT-PHY was found only on BCM4331 which is a BCMA-based chipset. This is
reallly unlikely we will ever see HT-PHY on SSB thus make the whole code
BCMA specific. This will allow us to call various BCMA-specific
functions directly (without extra checks).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the RX chainmask is set to 0x2 for AR9462, certain values
from chain1 have to be programmed for chain0 also.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This flag is used for indicating channel interference and
we currently do nothing with it, so remove it.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function brcmf_proto_hdrpush() increases the header space and
fills in the protocol header fields. One field is the data offset
which is currently fixed to zero meaning the data follows right
after the header. The parameter is added to determine the actual
start of data. This will be used for firmware signalling.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding a packet dequeue function that will return packets that
pass the provided match function.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For transmit packets the function brcmf_txcomplete() must be
called. This should be done as well when for some reason the
transmit fails to assure proper tx post processing. This patch
fixes the code paths in brcmf_usb_tx() that forgot to do so.
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the bus-specific driver code each call to brcmf_txcomplete() is
following by a free of that packet. This patch moves that free to
the brcmf_txcomplete() function.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware and host can exchange signals which are carried within
the data packets. These are TLV based signals that are inserted
before the actual data, ie. ethernet frame.

This commit adds the new source module for this feature and enables
RSSI signals from firmware.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added inline functions to set bitfields in an unsigned integer variable.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In preparation of firmware signalling feature additional headroom is
needed to accommodate signalling protocol data between host and
firmware.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In brcmf_cfg80211_sched_scan_start() the request parameter was checked
for being non-null. However, it never is so remove the check which gets
rid of following smatch warning:

drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c:2904
brcmf_cfg80211_sched_scan_start()
warn: variable dereferenced before check 'request' (see line 2897)
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The output of modinfo shows a bit of strangeness because module
information macros are used in multiple source files:

license:        Dual BSD/GPL
description:    Broadcom 802.11 wireless LAN fullmac driver.
author:         Broadcom Corporation
firmware:       brcm/brcmfmac-sdio.txt
firmware:       brcm/brcmfmac-sdio.bin
firmware:       brcm/brcmfmac43236b.bin
license:        Dual BSD/GPL
description:    Broadcom 802.11n wireless LAN fullmac usb driver.
author:         Broadcom Corporation

This patch cleans it up.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The module parameter definition for brcmf_msg_level has been
reworked to a named module parameter with description so
modinfo is a bit more informative:

parm:           debug:level of debug output (int)
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Inspired by tracing functionality added by Seth Forshee in the
brcmsmac driver, this patch adds similar functionality to brcmfmac.
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for radio on led indicator.
Control led via BCMA gpio driver.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
[arend@broadcom.com: modify Makefile for conditional compile led.c]
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This differs from legacy chips i.e.
a 8764 loads firmware image without a helper image
b Check interrupt status register for download
  complete indication.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch does the following:-

a Add entry in the PCIe table
b Add firmware support with API versioning
c Reuse most of the 8366 code
d Make 8764 specific changes where 8764 differs
  from 8366 e.g. structure definitions.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's harmless, but Smatch complains if we use "htc_hdr->eid" before
doing the bounds check.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  When make with EXTRA_CFLAGS=-W, it will report error.
  so give a check in Makefile.
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the embedded branch to make the ATH_EP_RND macro a little
clearer.  The new version also generates better code, saving 24
bytes of text:

   text	   data	    bss	    dec	    hex	filename
  87858	   1641	     24	  89523	  15db3	ath9k_orig.ko
  87834	   1641	     24	  89499	  15d9b	ath9k_new.ko

Although neither version handles negative values particularly well,
the lone caller clamps all negative values to zero anyway.  I have
verified that the results are the same for the range of possible
positive rssi values.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"translate" should either be set or disabled.  We also use it an
offset into the framing[] array when we're generating the proc
file.  Framing looks like this:

static const char *framing[] = { "Encapsulation", "Translation" }

So when we're setting translate we need to restrict the values to
either 1 or 0 or it can an out of bounds read.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stop returning negative values from ath5k_eeprom_mode_from_channel.
Yell loudly about that case in that function instead and return the
default/zero/mode A. This cleans up the callers, but needs to pass ah
down to ath5k_eeprom_mode_from_channel for ATH5K_WARN. For that
purpose we also need the declaration to be moved to ath5k.h.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

kfree on a NULL pointer is a no-op.
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Acked-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This exports the firmware version in use to userspace through ethtool.

root@OpenWrt:/# ethtool -i wlan0
firmware-version: 610.812
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With "mac80211/minstrel_ht: add support for using CCK rates"
minstrel_ht selects legacy CCK rates as viable rates for
outgoing frames which might be sent as part of an A-MPDU
[IEEE80211_TX_CTL_AMPDU is set].

This behavior triggered the following WARN_ON in the driver:
> WARNING: at carl9170/tx.c:995 carl9170_op_tx+0x1dd/0x6fd
The driver assumed that the rate control algorithm made a
mistake and dropped the frame.

This patch removes the noisy warning altogether and allows
said A-MPDU frames with CCK sample and/or fallback rates to
be transmitted seamlessly.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also add a missing 'the' before 'runtime performance'.
Signed-off-by: NW. Trevor King <wking@tremily.us>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BugLink: http://bugs.launchpad.net/bugs/1128840

It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: users@rt2x00.serialmonkey.com
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a more current logging style.

Convert ssb_dbprint to ssb_dbg too.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't require alignment of mac addresses to u16.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mac address should be aligned to u16 to prevent an unaligned access
in drivers/ssb/pci.c where it is casted to __be16.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>