The NOP OTG transceiver driver needs to be usable from modules.
Make sure its symbols are always accessible at both compile and
link time, and make sure the device instance is allocated from
the heap so that device lifetime rules are obeyed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.

For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.

The chip is controlled through the I2C bus.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

In addition to KT_DEAD which has limited support for diacriticals,
there is KT_DEAD2 that can support 256 criticals, so let's advertise
it in <linux/keyboard.h>.

This lets userland know abut the drivers/char/keyboard.c function
k_dead2, which supports more than the few trivial ones that k_dead
supports.
Signed-off-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Updated after review by Tim Abbott.
- Use HEAD_TEXT_SECTION
- Drop use of section-names.h and delete file
- Introduce EXIT_CALL

Deleting section-names.h required a few simple
updates of init.h
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Tim Abbott <tabbott@ksplice.com>

The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Acked-by: NSamuel Ortiz <sameo@openedhand.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

This patch adds the hlist_nulls_add_head() function which is
based on hlist_nulls_add_head_rcu() but without the use of
rcu_assign_pointer(). It also adds hlist_nulls_del which is
exactly the same like hlist_nulls_del_rcu().
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

commit 3f68535a (clocksource: sanity check sysfs clocksource
changes) prevents selection of non high resolution capable
clocksources when high resolution mode is active, but did not take
into account that the same rules apply for highres=off nohz=on.

Check the tick device mode instead of hrtimer_hres_active() to verify
whether the system needs to be protected from a switch to jiffies or
other non highres capable clock sources.
Reported-by: NLuming Yu <luming.yu@gmail.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

There is sometimes a need for the ocores driver to add devices to the
bus when installed.

i2c_register_board_info can not always be used, because the I2C devices
 are not known at an early state, they could for instance be connected
 on a I2C bus on a PCI device which has the Open Cores IP.

i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.

The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

git commit 0a0c5168 "PM: Introduce functions for suspending and resuming
device interrupts" introduced some helper functions. However these
functions are only available for architectures which support
GENERIC_HARDIRQS.

Other architectures will see this build error:

drivers/built-in.o: In function `sysdev_suspend':
(.text+0x15138): undefined reference to `check_wakeup_irqs'
drivers/built-in.o: In function `device_power_up':
(.text+0x1cb66): undefined reference to `resume_device_irqs'
drivers/built-in.o: In function `device_power_down':
(.text+0x1cb92): undefined reference to `suspend_device_irqs'

To fix this add some empty inline functions for !GENERIC_HARDIRQS.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

The *_nvs_* routines in swsusp.c make use of the io*map()
functions, which are only provided for HAS_IOMEM, thus
breaking compilation if HAS_IOMEM is not set. Fix this
by moving the *_nvs_* routines into hibernate_nvs.c, which
is only compiled if HAS_IOMEM is set.

[rjw: Change the name of the new file to hibernate_nvs.c, add the
 license line to the header comment.]
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This patch removes the legacy callbacks ->suspend() and
->resume() from struct device_type. These callbacks seem
unused, and new code should instead make use of struct
dev_pm_ops.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Remove the ->suspend_late() and ->resume_early() callbacks
from struct bus_type V2. These callbacks are legacy stuff
at this point and since there seem to be no in-tree users
we may as well remove them. New users should use dev_pm_ops.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:

	device_resume_noirq	dpm_resume_noirq
	device_resume		dpm_resume
	device_complete		dpm_complete
	device_suspend_noirq	dpm_suspend_noirq
	device_suspend		dpm_suspend
	device_prepare		dpm_prepare

in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.

In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).

Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().

The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.

Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()

Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NLen Brown <lenb@kernel.org>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

As explained by Benjamin Herrenschmidt:

  Oh and btw, your patch alone doesn't fix powerpc, because it's missing
  a whole bunch of GFP_KERNEL's in the arch code... You would have to
  grep the entire kernel for things that check slab_is_available() and
  even then you'll be missing some.

  For example, slab_is_available() didn't always exist, and so in the
  early days on powerpc, we used a mem_init_done global that is set form
  mem_init() (not perfect but works in practice). And we still have code
  using that to do the test.

Therefore, mask out __GFP_WAIT, __GFP_IO, and __GFP_FS in the slab allocators
in early boot code to avoid enabling interrupts.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

We no longer need an efficient mechanism to force the Guest back into
host userspace, as each device is serviced without bothering the main
Guest process (aka. the Launcher).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Currently, when a Guest wants to perform I/O it calls LHCALL_NOTIFY with
an address: the main Launcher process returns with this address, and figures
out what device to run.

A far nicer model is to let processes bind an eventfd to an address: if we
find one, we simply signal the eventfd.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: Davide Libenzi <davidel@xmailserver.org>

lguest never checked for pending interrupts when enabling interrupts, and
things still worked.  However, it makes a significant difference to TCP
performance, so it's time we fixed it by introducing a pending_irq flag
and checking it on irq_restore and irq_enable.

These two routines are now too big to patch into the 8/10 bytes
patch space, so we drop that code.

Note: The high latency on interrupt delivery had a very curious
effect: once everything else was optimized, networking without GSO was
faster than networking with GSO, since more interrupts were sent and
hence a greater chance of one getting through to the Guest!

Note2: (Almost) Closing the same loophole for iret doesn't have any
measurable effect, so I'm leaving that patch for the moment.

Before:
	1GB tcpblast Guest->Host:		30.7 seconds
	1GB tcpblast Guest->Host (no GSO):	76.0 seconds

After:
	1GB tcpblast Guest->Host:		6.8 seconds
	1GB tcpblast Guest->Host (no GSO):	27.8 seconds
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Add a new feature flag for indirect ring entries. These are ring
entries which point to a table of buffer descriptors.

The idea here is to increase the ring capacity by allowing a larger
effective ring size whereby the ring size dictates the number of
requests that may be outstanding, rather than the size of those
requests.

This should be most effective in the case of block I/O where we can
potentially benefit by concurrently dispatching a large number of
large requests. Even in the simple case of single segment block
requests, this results in a threefold increase in ring capacity.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Drivers don't add transport features to their table, so we
shouldn't check these with virtio_check_driver_offered_feature().

We could perhaps add an ->offered_feature() virtio_config_op,
but that perhaps that would be overkill for a consitency check
like this.
Signed-off-by: NMark McLoughlin <markmc@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This implements optional MSI-X support in virtio_pci.
MSI-X is used whenever the host supports at least 2 MSI-X
vectors: 1 for configuration changes and 1 for virtqueues.
Per-virtqueue vectors are allocated if enough vectors
available.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NAnthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ whitespace, style)

This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)

Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.

Also, add a "name" field for clearer debug messages.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Provide for means of extending the perf_counter_attr in a 'natural' way.

We allow growing the structure by appending fields at the end by specifying
the full structure size inside it.

When a new kernel sees a smaller (old) structure, it will 0 pad the tail.
When an old kernel sees a larger (new) structure, it will verify the tail
consists of 0s, otherwise fail.

If we fail due to a size-mismatch, we return -E2BIG and write the kernel's
native attribe size back into the provided structure.

Furthermore, add some attribute verification, so that we'll fail counter
creation when unknown bits are present (PERF_SAMPLE, PERF_FORMAT, or in
the __reserved fields).

(This ABI detail is introduced while keeping the existing syscall ABI.)
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

is_software_counter() was missing the new HW_CACHE category.

( This could have caused some counter scheduling artifacts
  with mixed sw and hw counters and counter groups. )
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It's theoretically possible that there are exception table entries
which point into the (freed) init text of modules.  These could cause
future problems if other modules get loaded into that memory and cause
an exception as we'd see the wrong fixup.  The only case I know of is
kvm-intel.ko (when CONFIG_CC_OPTIMIZE_FOR_SIZE=n).

Amerigo fixed this long-standing FIXME in the x86 version, but this
patch is more general.

This implements trim_init_extable(); most archs are simple since they
use the standard lib/extable.c sort code.  Alpha and IA64 use relative
addresses in their fixups, so thier trimming is a slight variation.

Sparc32 is unique; it doesn't seem to define ARCH_HAS_SORT_EXTABLE,
yet it defines its own sort_extable() which overrides the one in lib.
It doesn't sort, so we have to mark deleted entries instead of
actually trimming them.
Inspired-by: NAmerigo Wang <amwang@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: linux-alpha@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: linux-ia64@vger.kernel.org

Impact: API cleanup

For historical reasons, 'bool' parameters must be an int, not a bool.
But there are around 600 users, so a conversion seems like useless churn.

So we use __same_type() to distinguish, and handle both cases.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Impact: new API

__builtin_types_compatible_p() is a little awkward to use: it takes two
types rather than types or variables, and it's just damn long.

(typeof(type) == type, so this works on types as well as vars).
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Impact: cleanup

Rather than hack KPARAM_KMALLOCED into the perm field, separate it out.
Since the perm field was 32 bits and only needs 16, we don't add bloat.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

It takes an 'int' for historical reasons, and there are only two
users: simply switch it over to bool.

The other user (uvesafb.c) will get a (harmless-on-x86) warning until
the next patch is applied.

Cc: Brad Douglas <brad@neruo.com>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Now, SLAB is configured in very early stage and it can be used in
init routine now.

But replacing alloc_bootmem() in FLAT/DISCONTIGMEM's page_cgroup()
initialization breaks the allocation, now.
(Works well in SPARSEMEM case...it supports MEMORY_HOTPLUG and
 size of page_cgroup is in reasonable size (< 1 << MAX_ORDER.)

This patch revive FLATMEM+memory cgroup by using alloc_bootmem.

In future,
We stop to support FLATMEM (if no users) or rewrite codes for flatmem
completely.But this will adds more messy codes and overheads.
Reported-by: NLi Zefan <lizf@cn.fujitsu.com>
Tested-by: NLi Zefan <lizf@cn.fujitsu.com>
Tested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>

fs-internal parts of qnx4_fs.h taken to fs/qnx4/qnx4.h, includes adjusted,
qnx4_fs.h doesn't need unifdef anymore.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>