Let the user configure serveral TX error conection quality monitoring
parameters: % error rate, survey interval, and # of attempted packets.

On exceeding the TX failure rate over the given interval, the driver
will send a CQM notify event with the actual TX failure rate and
packets attempted.
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In one of my previous patches I erroneously
used nla_put_u32 for the wdev_id, fix that
to use nla_put_u64.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

info->control.sta and control.vif may only be dereferenced
during the drv_tx call otherwise could lead to use-after-free
bugs.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
[reword commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

commit "mac80211: unify SW/offload remain-on-channel"
moved the cookie assignment from ieee80211_mgmt_tx()
to ieee80211_start_roc_work().  But the latter is only
called where offchannel is needed.  If offchannel isn't
needed/used, a uninitialized cookie value would be returned
to userspace.

This patch sets the cookie value when offchannel isn't used.
Signed-off-by: NNicolas Cavallari <cavallar@lri.fr>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Revert commit b78e8cea
("cfg80211: track monitor channel") and remove the
set_monitor_enabled() callback.

Due to the tracking happening in NETDEV_PRE_UP, it had
introduced bugs because the monitor interface callback
would be called before the device was started. It looks
like there's no way to fix this, and using NETDEV_PRE_UP
is broken anyway (since there's no NETDEV_UP_FAIL), so
remove all that code, track interfaces in NETDEV_UP and
also stop tracking the monitor channel in cfg80211.

This mostly reverts to before the tracking, except that
we keep the interface count tracking so that setting the
monitor channel can be rejected properly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This essentially reverts commit 2e165b81 but
introduces the get_channel operation with a new
wireless_dev argument so that you can retrieve
the channel per interface. This is necessary as
even though we can track all interface channels
(except monitor) we can't track the channel type
used.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit 870d37fc.

This code doesn't work as cfg80211 will call
set_monitor_enabled at the wrong time and it
doesn't seem to be possible to fix this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

roc is destroyed then roc->started is referenced. Keep a local cache.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It may be desirable to use WoWLAN without triggers to
keep the connection alive to the AP while suspended.
Allow this use by enabling WoWLAN without triggers if
no triggers were requested.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Without this change, running AP + station on the same wiphy
does not work since the commit "cfg80211: add channel checking
for iface combinations". The stopped AP prevents the client
from connecting to an AP on a different channel.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[line-break commit message to < 72 chars]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the virtual monitor interface is requested
by the driver, it should also be iterated over
when the driver wants to iterate all active
interfaces.

To allow that protect it with the iflist_mtx.

Change-Id: I58ac5de2f4ce93d12c5a98ecd2859f60158d5d69
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To call cfg80211_get_chan_state() we need to lock
the wdev, so we need to lock the wdev_iter mutex
in cfg80211_can_use_iftype_chan(). This needs to
use nested locking for lockdep.

Also, cfg80211_get_chan_state() doesn't actually
use the rdev, so remove that completely including
the lock assertion that isn't needed.
Reported-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When sample_idx is set to a value other than -1 it activates
the IEEE80211_TX_CTL_RATE_CTRL_PROBE flag which disables
frame aggregation. To allow frame aggregation during fixed
rate it is necessary to set max_tp_rate, max_tp_rate2 and
max_prob_rate instead of sample_idx.
Signed-off-by: NSylvain Roger Rieunier <sylvain.roger.rieunier@gmail.com>
[reword commit message a bit]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When drop_unencrypted is enabled and MFP is disabled,
non-robust management frames for not-yet associated STA are dropped.
This isn't visible as many management frames sent from the kernel
have TX_INTFL_DONT_ENCRYPT set and management frames injected
from a monitor vif have TX_CTL_INJECTED so aren't dropped.
But management frames sent from userspace via NL80211_CMD_FRAME
do not have this flag set, so are dropped.

This patch make it always accept non-robust management frames.
Signed-off-by: NNicolas Cavallari <cavallar@lri.fr>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The "no key" case in key selection that decides
whether to drop the frame or not is impossible
to understand, restructure the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
[cavallar@lri.fr: removed blank line and restructured action frame clause]
Signed-off-by: NNicolas Cavallari <cavallar@lri.fr>

Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.

To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.

Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We waste a lot of space in this struct because it uses
int values where smaller ones would be sufficient. The
upcoming A-MPDU information needs some space, optimize
the struct now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Scan receive is rather inefficient when there are
multiple virtual interfaces. We iterate all of the
virtual interfaces and then notify cfg80211 about
each beacon many times.

Redesign scan RX to happen before everything else.
Then we can also get rid of IEEE80211_RX_IN_SCAN
since we don't have to accept frames into the RX
handlers for scanning or scheduled scanning any
more. Overall, this simplifies the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of tracking whether or not we're in a
scheduled scan, track the virtual interface
(sdata) in an RCU-protected pointer to make it
usable from RX to check the MAC address.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Making the scan_sdata pointer usable with RCU makes
it possible to dereference it in the RX path to see
if a received frame actually matches the interface
that is scanning. This is just preparations, making
the pointer __rcu.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function building probe-request IEs does not validate the band is
supported before dereferencing it. This can result in a panic when
all bands are traversed, as done during sched-scan start.

Warn when this happens and return an empty probe request. Also fix
sched-scan to not waste memory on unsupported bands.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

After a new virtual interface is created, reply
to userspace with a message detailing it so it
knows the new wdev identifier.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to be able to create P2P Device wdevs, move
the virtual interface management over to wireless_dev
structures.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a few places that iterate the wdev
list and assume wdev->netdev exists, check
there. The rfkill one has to be extended for
each non-netdev type later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since soon there will be virtual interfaces that
don't have a netdev, use the wdev identifier for
the API to retrieve interface data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some nl80211 callbacks will soon need the wdev instead
of the netdev, so add NL80211_FLAG_NEED_WDEV to allow
them to request that. Add NL80211_FLAG_NEED_WDEV_UP as
well which checks the netdev is UP if one exists.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to support a P2P device abstraction and
Bluetooth high-speed AMPs, we need to have a way
to identify virtual interfaces that don't have a
netdev associated.

Do this by adding a NL80211_ATTR_WDEV attribute
to identify a wdev which may or may not also be
a netdev.

To simplify things, use a 64-bit value with the
high 32 bits being the wiphy index for this new
wdev identifier in the nl80211 API.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This API call was intended to be used by drivers
if they want to optimize key handling by removing
one key when another is added. Remove it since no
driver is using it. If needed, it can always be
added back.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ieee80211_mlme_notify_scan_completed() iterates all
interfaces and doesn't need to assign anything to
the sdata variable before the loop.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the AC parameters change, drivers might rely
on getting a bss_info_changed notification with
BSS_CHANGED_QOS in addition to the conf_tx call.

Always call the function when userspace updates
are made (in AP/GO modes) and also set the change
flag when updates were made by the AP (in managed
mode.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Quick fix for method being invoked without checking its existence.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Because ieee80211_tx_status in status.c checks if
outgoing BlockAck requests have been acked, it is
necessary to tell the driver that tx feedback for
this sort of frame is important.

Otherwise, the stack will continue to send the same
BlockAck request over and over, which can cause
the receiver to flush or clean its reorder buffer
over and over.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This was useful for debugging the queue stop/wake
issues and is pretty small so let's just put it in.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Larry (and some others I think) reported that with
single-queue drivers mac80211 crashes when waking
the queues. This happens because we allocate just
a single queue for each virtual interface in case
the driver doesn't have at least 4 queues, but the
code stopping/waking the virtual interface queues
wasn't taking this into account.
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the interfaces were removed just before a restart
work was started, open_count will be 0, and most of
the reconfig work will be skipped, including the
resetting of local->in_reconfig to false.

Leaving local->inconfig = true will result in
dropping any incoming packet.

Fix it by always setting local->in_reconfig = false
(even if there are no active interfaces).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Due to the way the default key links are created,
it happens that a link is left dangling:
 * both unicast/multicast links are created
 * unicast link is destroyed, and the links
   are updated
 * during this update, adding the multicast
   link again fails because it is present,
   destroying the debugfs pointer
 * removing the multicast link won't work as
   the pointer has been destroyed

Fix this by always removing the links and then
re-creating them if needed.
Reported-by: NMarek Lindner <lindner_marek@yahoo.de>
Reported-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

60g band uses different from .11n MCS scheme, so bitrate
should be calculated differently
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Until now, a u16 value was used to represent bitrate value.
With VHT bitrates this becomes too small.

Introduce a new 32-bit bitrate attribute. nl80211 will report
both the new and the old attribute, unless the bitrate doesn't
fit into the old u16 attribute in which case only the new one
will be reported.

User space tools encouraged to prefer the 32-bit attribute, if
available (since it won't be available on older kernels.)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[reword commit message and comments a bit]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>