This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle.  This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available.  When the PHY is powered down, the clock the MAC depends on
is disabled.  The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates.  The tg3 driver has code to detect this
condition and resets the device during initialization.  On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761.  However, during this initialization stage, communications
to the APE registers have not yet been set up.  The driver then
dereferences a NULL pointer and crashes the machine.  The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A reasonably common problem with some devices is that they will
disable MSI generation when the INTX_DISABLE bit is set in the
PCI_COMMAND register.

Quirk this explicitly, guarding the pci_intx() calls in msi.c with
this quirk indication.

The first entries for this quirk are for 5714 and 5780 Tigon3 chips,
and thus we can remove the workaround code from the tg3.c driver.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates the version number to 3.85.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the way the driver works with the PCI command
register.  It adjusts the access size from dwords to words.  This patch
is done both as a PCI configuration space cleanup and as preparatory
work for PCI error recovery.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch appends the management firmware version to the bootcode
firmware string reported through ethtool.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for upcoming 5723 devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will convert remaining non-obvious or naive calculations of array
sizes to use ARRAY_SIZE() macro.
Signed-off-by: NAlejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A performance regression was introduced by the following commit:

    commit ee6a99b5
    Author: Michael Chan <mchan@broadcom.com>
    Date:   Wed Jul 18 21:49:10 2007 -0700

    [TG3]: Fix msi issue with kexec/kdump.

In making that change, the PCI latency timer and cache line size
registers were not restored after chip reset.  On the 5705, the
latency timer gets reset to 0 during chip reset and this causes
very poor performance.

Update version to 3.84.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to read and store sblk->status_tag before checking for more work.
The status tag is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed.  If the
order is reversed, we can end up acknowledging work we haven't
processed.

When we detect tx error, it is more correct to return the rx
work_done so far instead of 0.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():

		/* Drivers must not modify the NAPI state if they
		 * consume the entire weight.  In such cases this code
		 * still "owns" the NAPI instance and therefore can
		 * move the instance around on the list at-will.
		 */

A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.

BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update to version 3.83.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables WOL by default if out-of-box WOL is enabled in the
NVRAM.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds rest of the miscellaneous code required to support the
5761.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the new APE block, present in 5761 chips.
APE stands for Application Processing Engine.  The primary function of
the APE is to process manageability traffic, such as ASF.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new 5761-specific NVRAM strapping decode routine.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I recently noticed that when calling:

# ethtool -s eth0 autoneg on

on a 5722 (though I'm sure it's not specific to that card) that
subsequent checks of the cards status looked like this:

# ethtool eth0
Settings for eth0:
        Supported ports: [ MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised auto-negotiation: No        <---- This seems odd?!?
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: d
        Current message level: 0x000000ff (255)
        Link detected: yes

I noticed that the following commit:

commit 3600d918
Author: Michael Chan <mchan@broadcom.com>
Date:   Thu Dec 7 00:21:48 2006 -0800

    [TG3]: Allow partial speed advertisement.

    Honor the advertisement bitmask from ethtool.  We used to always
    advertise the full capability when autoneg was set to on.

changed things around so that ethtool speed settings were strictly
followed.  Unfortunately ethtool doesn't seem to set ADVERTISED_Autoneg
in the advertising field (and maybe it shouldn't have to).  I'd vote
that it should be fixed there, but it should also be added here just in
case someone using ethtool ioctls in their own application gets what
they want.

Adding that flag in tg3_set_settings seemed like the most logical place
since the driver works fine on boot.  This is just an issue when
re-enabling autonegotiation, so we should probably nip it there.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support for 5784 and 5764 devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer products change the way the ASIC revision is obtained.  This patch
implements how the driver will extract the revision number.

This patch also adds preliminary CPMU support.  CPMU stands for Central
Power Management Unit.  The CPMU's role is to put the chip into lower
power states when the operating conditions allow it.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer tg3 devices shuffle around the registers in PCI configuration
space.  This patch changes the way the driver accesses the PCI
capabilities registers.  Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the operations
	get-tx-csum
	get-sg
	get-tso
	get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.

This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.

The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case.  Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.

[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it.  The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.

[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed sparse warnings from tg3 driver.  The new logic seems fine (I
don't immediately see where we are running over values for any of the
variables that need to be saved).

This patch compiles fine and I'm currently using a tg3 with the patched
driver to post this patch as a basic proof of concept.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.

In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.

The signature of the ->poll() call back goes from:

	int foo_poll(struct net_device *dev, int *budget)

to

	int foo_poll(struct napi_struct *napi, int budget)

The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract).  The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.

The napi_struct is to be embedded in the device driver private data
structures.

Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler.  Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.

With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.

Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.

[ Ported to current tree and all drivers converted.  Integrated
  Stephen's follow-on kerneldoc additions, and restored poll_list
  handling to the old style to fix mutual exclusion issues.  -DaveM ]
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A hardware bug was revealed after a recent PCI MSI patch was made to
always disable legacy INTX when enabling MSI.  The 5714/5780 chips
will not generate MSI when INTX is disabled, causing MSI failure
messages to be reported, and another patch was made to workaround the
problem by disabling MSI on ServerWorks HT1000 bridge chips commonly
found with the 5714.

We workaround this chip bug by enabling INTX after we enable MSI and
after we resume from suspend.

Update version to 3.81.

This problem was discovered by David Miller.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended.  In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.

We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function.  So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tina Yang <tina.yang@oracle.com> discovered an MSI related problem
when doing kdump.  The problem is that the kexec kernel is booted
without going through system reset, and as a result, MSI may already
be enabled when tg3_init_one() is called.  tg3_init_one() calls
pci_save_state() which will save the stale MSI state.  Later on in
tg3_open(), we call pci_enable_msi() to reconfigure MSI on the chip
before we reset the chip.  After chip reset, we call
pci_restore_state() which will put the stale MSI address/data back
onto the chip.

This is no longer a problem in the latest kernel because
pci_restore_state() has been changed to restore MSI state from
internal data structures which will guarantee restoring the proper
MSI state.

But I think we should still fix it.  Our save and restore sequence
can still cause very subtle problems down the road.  The fix is to
have our own functions save and restore precisely what we need.  We
also change it to save and restore state inside tg3_chip_reset() in a
more straight forward way.

Thanks to Tina for helping to test and debug the problem.

[ Bump driver version and release date. -DaveM ]
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool utility function to set or clear IPV6_CSUM feature flag.
Modify tg3.c and bnx2.c to use this function when doing ethtool -K
to change tx checksum.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a missing NVRAM strapping for 5755 devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds automatic MDI crossover support when autonegotiation is
turned off.  Automatic MDI crossover allows link to be established
without the use of a crossover cable.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For most pre-5705 devices, multiple link interrupts were being generated
for a single physical link change.  The source of the interrupts was
determined to be unnecessary toggling of the MAC link polarity bit.

This patch changes the way the link polarity bit gets configured.  Where
possible, code that dynamically configures the bit in response to link
changes has been replaced by code that configures the bit once during
initialization time and then leaves the bit alone.

For correctness, this patch also limits the use of the bit to those
devices where it is defined, namely devices before the 5705.  This patch
also corrects the link polarity configurations for 5700 devices when
paired against a bcm5411 phy.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gagan Arneja <gaagaan@gmail.com> pointed out that tg3_reset_task()
could potentially race with another thread calling tg3_full_lock()
such as the ethtool_set_xxx() functions.  This may trigger the
BUG_ON() in tg3_irq_quiesce() or cause the irq_sync flag to be out-
of-sync.

I think the easiest way to fix this is to get the tp->lock first
before setting the irq_sync flag.  This is safe to do because the
tp->lock is never grabbed by the irq handler.  This change will
guarantee that the irq_sync flag updates will be serialized.  We also
have to change one spot to call tg3_netif_start() (which clears the
irq_sync flag) before releasing the tp->lock.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The existing model for checksum offload does not correctly handle
devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag
implies device can do any arbitrary protocol.

This patch:
 * adds NETIF_F_IPV6_CSUM for those devices
 * fixes bnx2 and tg3 devices that need it
 * add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO)
 * fixes assumptions about NETIF_F_ALL_CSUM in nat
 * adjusts bridge union of checksumming computation
Signed-off-by: NDavid S. Miller <davem@davemloft.net>