Reduces the number of calls to register ops. On MIPS this reduces the
ath9k_hw binary size from 321k down to 310k
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With this change, loading the address to a register read/write function
costs only one pointer dereference instead of two. On MIPS this reduces
ath9k_hw binary size from 326k down to 321k.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for using RSN IBSS with ath9k. For now, this uses software
crypto for group addressed frames in RSN IBSS, but that may be
optimized in the future by extending the key cache design to support
per-STA RX GTK.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stuck beacon detection is supposed to trigger when 9 consecutive beacons
could not be sent by the hardware. When the driver runs only one active
AP mode interface, it still configures the hardware beacon timer for
4 (ATH_BCBUF) beacon slots slots, which causes stuck beacon detection
to be reset if ath9k_hw_stoptxdma clears the stuck frames between
SWBA intervals.
Fix this by not resetting the missed beacon count for empty slots and
multiplying the threshold not by the maximum number of beacon slots
but by the configured number of beacon interfaces.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Single missed (i.e. not transmitted) beacons in AP mode are not very rare
and not necessarily an indicator of strong interference, so only trigger
noise floor recalibration when multiple consecutive beacons could not
be transmitted.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.

To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for suspend/resume in if_spi.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver adds WiFi support for Marvell 802.11n based chipsets
with SDIO interface. Currently only SD8787 is supported. More
chipsets will be supported later.

drivers/net/wireless/mwifiex/
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NRamesh Radhakrishnan <rramesh@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only AR9485 1.1 was sold. This debloats the driver by ~14 KiB.

   text    data     bss     dec     hex filename
 300413     624    1056  302093   49c0d drivers/net/wireless/ath/ath9k/ath9k_hw.ko

   text    data     bss     dec     hex filename
 310285     624    1056  311965   4c29d drivers/net/wireless/ath/ath9k/ath9k_hw-old.ko

$ du -b ath9k_hw*
6210541	ath9k_hw.ko
6225089	ath9k_hw-old.ko

Cc: Bill Wu <bill.wu@atheros.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Forbes Tsai <Forbes.Tsai@Atheros.com>
Cc: Jesmine Chen <jesmine.chen@atheros.com>
Cc: Marvian Chen <Hou-hua.Chen@Atheros.com>
Cc: Vivek Natarajan <vivek.natarajan@atheros.com>
Cc: Bernadette Yetso <bernadette.yetso@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Acked-by: NYi-Chen Su <yi-chen.su@atheros.com>
Acked-by: NJeffrey Chung <jeffrey.chung@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This workaround called ath_txq_schedule whenever there were still pending
frames for a queue, but the queue depth was zero. Because of its its high
false positive probability (e.g. with paused TIDs) and because it is in
the way of other pending work (AP powersave fixes), it is better to remove
this code entirely.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Most AR9100 devices already have a chainmask of 7 (three antennas), however
on the ones that don't (rx and tx chainmask set to 5), problems with IQ
mismatch calibration have been observed.
This shows up as tx queue hangs (and subsequent hardware resets) if traffic
is sent during this type of calibration.
Forcing the rx chainmask to 7 fixes the calibration issues with no apparent
negative side effects on throughput and stability.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes interop issues with aggregation in combination with multi-BSSID
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On some devices the correct MAC address is not in the EEPROM data, but
stored somewhere else.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some devices control antenna settings or other things through GPIO pins
of the wireless interface. Add a debugfs interface for changing those
and keeping them set across card resets.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since the ath9k debugfs directory is cleaned up by debugfs_remove_recursive,
there's no point in checking the return code of every single debugfs create
line.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Queue ADDBA requests in respective data queues to avoid ADDBA
requests and the the related data packets (to the same ra/tid)
queued in the hardware to be sent out asynchronously.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the outgoing packet rate to a particular HT station is <=6.5
Mbps, do not attempt to create an ampdu. Also, if the outgoing
rate is legacy rate, do not create an ampdu.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an ampdu stream is on, if the firmware rate adaptation
logic decides that the outgoing packet rate to the station needs
to go below 6.5Mbps (non HT rate), it sends an event indicating that
the ampdu stream needs to be destroyed. Handle this event in the driver
and destroy the ampdu stream so that the rate can go below 6.5Mbps
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Specifically, handle ampdu_action and attempt to start a BA
session on receiving the first qos packet from mac80211 for
transmission to a HT sta.  While the BA session is being created,
all the packets belonging to that stream will be dropped to
prevent sequence number mismatch at the recipient.

Contains contributions from:
Yogesh Powar <yogeshp@marvell.com>
Pradeep Nemavat <pnemavat@marvell.com>
Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In particular, we can now add, start, lookup, and remove streams.

Based on work by Nishant Sarmukadam <nishants@marvell.com> and
Pradeep Nemavat <pnemavat@marvell.com>.
Signed-off-by: NPradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We now have two different kinds of queues.  And the number of
AMPDU queues may vary.  So we must be clear about which queues we
are dealing with.  Note that when we report the number of queues
to mac80211, we only report the WMM queues.

Based on work by Yogesh Powar <yogeshp@marvell.com>.
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware APIv2 adds the following enhancements:

-- capabilities are reported by the firmware
-- API supports up to 8 dedicated AMPDU streams
-- optional packet timestamping and expiration can be enabled.
   Specifically, packets that are queued in firmware for longer
   than 500ms will be dropped if this option is used.

Based on work by "Nishant Sarmukadam" <nishants@marvell.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Specifically, APIv2 will specify a variable number of AMPDU
queues in the MWL8K_CMD_GET_HW_SPEC.  So init the tx queues after
MWL8K_CMD_GET_HW_SPEC for ap fw.

Also, we make it safe to deinit queues that have not been init'd.
This happens if the mwl8k_get_hw_spec_ap routine fails, for
example.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NBrian Cavagnolo <brian@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fine-tuning register write operation and avoid unnecessay
delays for ath9k_htc driver, saves hw reset time which
improves scanning time and also solves one of the following
scenario.

Sometimes the ACK is sent by STA for assoc response is not
seen at AP side. So the AP continues to send retry assoc
responses. At the STA side, since the assoc response was
already forwarded to mac80211, it proceeded to channel change
which in turns does chip reset.

In most of the cases the chip reset was completed before
max retries are reached at AP side. Hence STA can able to ACK
the retried frames again. But in clear environment these retries
are completed within shortspan of time.

Since ath9k_htc consumes more time for hw reset, this latency
is causing dissociation by AP due to max reties are reached.
This issue was originally reported with Cisco Aironet 1250 AP
in HT40 mode in noise free environment.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By enabling buffered register write for ath9k_htc driver
avoids unnecessary dissociation while rekeying phase under
heavy traffic exchange.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Doing adc gain calibration for AR9287 chips is causing
throughput drops in HT40 mode. Remove ADC Gain from supported
calibration list.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We initialize exit_pending twice.  It's the second initialization which
is correct.  That was added in d745d472 "iwlwifi: cancel scan when
down the device".
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Scripted with coccinelle.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

commit 86271e46 introduced a
regression that caused mac80211 queues in stopped state.

ath_drain_all_txq is called in driver flush which would reset
the stopped flag and the mac80211 queues were never started
after that. iperf traffic is completely stalled due to this issue.

Restart the mac80211 queues in driver flush only if the txqs were
drained.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the recent tx status optimization in mac80211, we bail out as
and and when invalid rate index is found. So the behavior of resetting
rate idx to -1 and count to 0 has changed for the rate indexes that
were not part of the driver's retry series.

This has resulted in ath9k using incorrect rate table index which
caused the system to panic. Ideally ath9k need to loop only for the
indexes that were part of the retry series and so simply use hw->max_rates
as the loop counter.

Pasted the stack trace of the panic issue for reference.

[  754.093192] BUG: unable to handle kernel paging request at ffff88046a9025b0
[  754.093256] IP: [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
[  754.094888] Call Trace:
[  754.094903]  <IRQ>
[  754.094928]  [<ffffffffa051f883>] ieee80211_tx_status+0x203/0x9e0 [mac80211]
[  754.094975]  [<ffffffffa053e305>] ? __ieee80211_wake_queue+0x125/0x140 [mac80211]
[  754.095017]  [<ffffffffa02e66c9>] ath_tx_complete_buf+0x1b9/0x370 [ath9k]
[  754.095054]  [<ffffffffa02e6fcf>] ath_tx_complete_aggr+0x51f/0xb50 [ath9k]
[  754.095098]  [<ffffffffa05382a3>] ? ieee80211_prepare_and_rx_handle+0x173/0xab0 [mac80211]
[  754.095148]  [<ffffffff81350e62>] ? _raw_spin_unlock_irqrestore+0x32/0x40
[  754.095186]  [<ffffffffa02e9735>] ath_tx_tasklet+0x365/0x4b0 [ath9k]
[  754.095224]  [<ffffffff8107a2a2>] ? clockevents_program_event+0x62/0xa0
[  754.095261]  [<ffffffffa02e2628>] ath9k_tasklet+0x168/0x1c0 [ath9k]
[  754.095298]  [<ffffffff8105599b>] tasklet_action+0x6b/0xe0
[  754.095331]  [<ffffffff81056278>] __do_softirq+0x98/0x120
[  754.095361]  [<ffffffff8100cd5c>] call_softirq+0x1c/0x30
[  754.095393]  [<ffffffff8100efb5>] do_softirq+0x65/0xa0
[  754.095423]  [<ffffffff810563fd>] irq_exit+0x8d/0x90
[  754.095453]  [<ffffffff8100ebc1>] do_IRQ+0x61/0xe0
[  754.095482]  [<ffffffff81351413>] ret_from_intr+0x0/0x15
[  754.095513]  <EOI>
[  754.095531]  [<ffffffff81014375>] ? native_sched_clock+0x15/0x70
[  754.096475]  [<ffffffffa02bcfa6>] ? acpi_idle_enter_bm+0x24d/0x285 [processor]
[  754.096475]  [<ffffffffa02bcf9f>] ? acpi_idle_enter_bm+0x246/0x285 [processor]
[  754.096475]  [<ffffffff8127fab2>] cpuidle_idle_call+0x82/0x100
[  754.096475]  [<ffffffff8100a236>] cpu_idle+0xa6/0xf0
[  754.096475]  [<ffffffff81339bc1>] rest_init+0x91/0xa0
[  754.096475]  [<ffffffff814efccd>] start_kernel+0x3fd/0x408
[  754.096475]  [<ffffffff814ef347>] x86_64_start_reservations+0x132/0x136
[  754.096475]  [<ffffffff814ef451>] x86_64_start_kernel+0x106/0x115
[  754.096475] RIP  [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On hardware busy the scan request pointer should be cleared, as higher
levels will release. This avoids a crash when that pointer is
erroneously used later.
Signed-off-by: NJoseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clearly a mistake, since pointers won't suddenly
change their value...
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel panic occurs just after AR2427 establishes connection with AP.
Unless aggregation is enabled we don't initialize the TID structure.
Thus accesing the elements of the TID structure when aggregation is
disabled, leads to NULL pointer dereferencing.

[  191.320358] Call Trace:
[  191.320364]  [<fd250ea7>] ? ath9k_tx+0xa7/0x200 [ath9k]
[  191.320376]  [<fd1ec7fc>] ? __ieee80211_tx+0x5c/0x1e0 [mac80211]
[  191.320386]  [<fd1edd2b>] ? ieee80211_tx+0x7b/0x90 [mac80211]
[  191.320395]  [<fd1edddd>] ? ieee80211_xmit+0x9d/0x1d0 [mac80211]
[  191.320401]  [<c014218f>] ? wake_up_state+0xf/0x20
[  191.320405]  [<c015dbc8>] ? signal_wake_up+0x28/0x40
[  191.320410]  [<c012a578>] ? default_spin_lock_flags+0x8/0x10
[  191.320420]  [<fd1ee308>] ? ieee80211_subif_start_xmit+0x2e8/0x7c0
[mac80211]
[  191.320425]  [<c058f905>] ? do_page_fault+0x295/0x3a0
[  191.320431]  [<c04c4a3d>] ? dev_hard_start_xmit+0x1ad/0x210
[  191.320436]  [<c04d96b5>] ? sch_direct_xmit+0x105/0x170
[  191.320445]  [<fd1f161a>] ? get_sta_flags+0x2a/0x40 [mac80211]
[  191.320449]  [<c04c780f>] ? dev_queue_xmit+0x37f/0x4b0
[  191.320452]  [<c04d75b0>] ? eth_header+0x0/0xb0
[  191.320456]  [<c04cc479>] ? neigh_resolve_output+0xe9/0x310
[  191.320461]  [<c053d295>] ? ip6_output_finish+0xa5/0x110
[  191.320464]  [<c053e354>] ? ip6_output2+0x134/0x250
[  191.320468]  [<c053f7dd>] ? ip6_output+0x6d/0x100
[  191.320471]  [<c0559665>] ? mld_sendpack+0x395/0x3e0
[  191.320475]  [<c0557f81>] ? add_grhead+0x31/0xa0
[  191.320478]  [<c055a83c>] ? mld_send_cr+0x1bc/0x2b0
[  191.320482]  [<c01535d9>] ? irq_exit+0x39/0x70
[  191.320485]  [<c055a940>] ? mld_ifc_timer_expire+0x10/0x40
[  191.320489]  [<c015b92e>] ? run_timer_softirq+0x13e/0x2c0
[  191.320493]  [<c0103a30>] ? common_interrupt+0x30/0x40
[  191.320498]  [<c055a930>] ? mld_ifc_timer_expire+0x0/0x40
[  191.320502]  [<c0153358>] ? __do_softirq+0x98/0x1b0
[  191.320506]  [<c01534b5>] ? do_softirq+0x45/0x50
[  191.320509]  [<c0153605>] ? irq_exit+0x65/0x70
[  191.320513]  [<c05917dc>] ? smp_apic_timer_interrupt+0x5c/0x8b
[  191.320516]  [<c0103df1>] ? apic_timer_interrupt+0x31/0x40
[  191.320521]  [<c016007b>] ? k_getrusage+0x12b/0x2f0
[  191.320525]  [<c039e384>] ? acpi_idle_enter_simple+0x117/0x148
[  191.320529]  [<c04a20da>] ? cpuidle_idle_call+0x7a/0x100
[  191.320532]  [<c01021d4>] ? cpu_idle+0x94/0xd0
[  191.320536]  [<c057ab88>] ? rest_init+0x58/0x60
[  191.320541]  [<c07a58ec>] ? start_kernel+0x351/0x357
[  191.320544]  [<c07a53c7>] ? unknown_bootoption+0x0/0x19e
[  191.320548]  [<c07a50aa>] ? i386_start_kernel+0xaa/0xb1
[  191.320550] Code: 03 66 3d 00 03 0f 84 7c 02 00 00 83 c3 18 0f b6 03
8b 4d e0 89 c3 83 e3 0f 6b c3 48 89 5d d8 8d 04 06 8d 50 0c 89 55 d0 8b
40 20 <8b> 00 3b 01 0f 85 8e 02 00 00 f6 47 20 40 0f 84 29 ff ff ff 8b
[  191.320634] EIP: [<fd2586d4>] ath_tx_start+0x474/0x770 [ath9k] SS:ESP
0068:c0761a90
[  191.320642] CR2: 0000000000000000
[  191.320647] ---[ end trace 9296ef23b9076ece ]---
[  191.320650] Kernel panic - not syncing: Fatal exception in interrupt

Cc: stable@kernel.org
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These were found using the following semantic match:
// <smpl>
@@expression E1; type T;@@
* memset(E1, ... * sizeof(T) * ..., ...);
// </smpl>

Also take this opportunity to remove the unnecessary void* casts.
Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add unknown Toshiba device, mentioned in rt3572sta sources, under
CONFIG_RT2800USB_UNKNOWN
Signed-off-by: NPeter Lemenkov <lemenkov@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add 2L Central Europe BV 8070 under CONFIG_RT2800USB_UNKNOWN
Signed-off-by: NPeter Lemenkov <lemenkov@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>