This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later.  This patch just
reorders the code hunks in what I believe was the intended sequence.

Coverity: CID 12600999Signed-off-by: NJohn W Linville <linville@tuxdriver.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the function i40e_rx_is_fip() that is not used anywhere.

This was partially found by using a static code analysis program
called cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.6 and i40evf to 1.2.0 version.

Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add parsing and reporting of iSCSI capability for a given device or
function.

Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.

Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.

Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.

Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.

Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add lldp control commands, add oem ocsd and ocbb commands.

Change-ID: I89eba2bd02013d0a44e1ce900559c54bb15f4a66
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix up NVM config read and write data structs.
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.

Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.

Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We should not be doing Tx or Rx timestamps if we do not have PTP
enabled. Add checks to ensure that we don't attempt to handle any PTP
related timestamping code if we have not enabled PTP on that PF.

Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We should not blindly enable the PTP interrupt flags for all PFs. We
should only enable the PTP interrupt in PFs which have enabled
PTP.

Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.5 and i40evf to 1.0.7.

Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Dump Stats string has been removed from functional debugfs
help message. Now it does not show up when we echo command to
debugfs/Fortville queue.

Change-ID: I9333473826b574f1afa6ddb785fd7adfbdcb2884
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch creates a define for interrupt name string configuration that
is large enough to contain full bus/slot info, rather than just netdev->name.

Change-ID: Iaac0d23dfb8526defeed69d91cea85ed4a50ddb2
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need to give up in the reset/rebuild process if the DCB setup failed,
so handle it here the same as in the probe setup.  Also adjust the log strings
a little to look less scary.

Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where the /proc/interrupts descriptions
from the msix configuration were truncating the needed bus info,
making it hard to distinguish configuration from port to port.
This patch increases the string buffer size in order to allow the
full data to be displayed and sync's the text formatting of the misc
and fdir interrupt names

Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Increase ASQ timeout for some scenarios with multi-function devices

Change-ID: I2d7655b19e6c6f9a7ad04deacb106ca8d53886db
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several little tweaks to keep FW, SV, and SW in line together
 - Remove the unused and deprecated
   i40e_aqc_opc_debug_modify_internals
 - Add define for iSCSI capability
 - Fix queue mask size
 - Adjust i40e_aqc_oem_param_change for ease-of-use

Change-ID: I51f250b367912968a7cec61b3a68110d9796e914
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NKamil Kacperski <kamil.kacperski@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.

This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.

The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.

CC: <stable@vger.kernel.org>
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure we only allow SR/IOV on the master PF of a port in multifunction
mode.  This should be the case anyway based on the num_vfs configured in
the NVM, but this will help make sure there's no question.  If we're not
in multifunction mode the partition_id will always be 1.

Change-ID: I8b2592366fe6782f15301bde2ebd1d4da240109d
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were only checking if the link up state had changed,
and if it hadn't exiting the link event routine early. We should
also check if speed has changed, and if it has, stay and finish
processing the link event.

Change-ID: I9c8e0991b3f0279108a7858898c3c5ce0a9856b8
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When in multi-function mode, e.g. Dell's NPAR, only partition 1
of each MAC is allowed to set WoL, speed, and flow control.

Change-ID: I87a9debc7479361c55a71f0120294ea319f23588
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Function will read PBA Block from Shadow RAM and return it in a string format.

Change-ID: I4ee7059f6e21bd0eba38687da15e772e0b4ab36e
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When in NPAR mode the driver instance might be controlling the base
partition or one of the other "fake" PFs.  There are some things that
can only be done by the base partition, aka partition_id 1.  This code
does a bit of work to find how many partitions are there per port and
what is the current partition_id.

Change-ID: Iba427f020a1983d02147d86f121b3627e20ee21d
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These mac address already added by FCoE stack above netdev,
therefore adding them here is redundant.

Change-ID: Ia5b59f426f57efd20f8945f7c6cc5d741fbe06e5
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

NPAR enabled partitions should warn the user when detected link speed is
less than 10Gpbs.

Change-ID: I7728bb8ce279bf0f4f755d78d7071074a4eb5f69
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If VF drivers are loaded in the host OS, the call to pci_disable_sriov()
will cause these drivers' remove routines to be called. If the PF driver
has already freed VF resources before this happens, then the VF remove
routine can't properly communicate with the PF driver causing all sorts
of mayhem and error messages and hurt feelings.

To fix this, we move the call to pci_disable_sriov() up to the top of
the function and let it complete before freeing any VF resources.

Change-ID: I397c3997a00f6408e32b7735273911e499600236
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was examining the outer protocol layer to set the inner protocol
layer checksum offload.  In the case of TCP over IPV6 over an IPv4 based
VXLAN the inner checksum offloads would be set to look for IPv4/UDP instead
of IPv6/TCP.  This code fixes that so that the driver will look at the
proper layer for encapsulation offload settings.
Signed-off-by: NAnjali Singhai <anjali.singhai@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Rx port checksum error counter was incrementing incorrectly with
UDP encapsulated tunneled traffic.  This patch fixes the problem so that
the port_rx_csum counter will show accurate statistics.
Signed-off-by: NAnjali Singhai <anjali.singhai@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the driver was polling with interrupts disabled the hardware
will occasionally not write back descriptors.  This patch causes
the driver to detect this situation and force an interrupt to
fire which will flush the stuck descriptor.  Does not conflict
with napi because if we are already polling the napi_schedule is
ignored.  Additionally the extra interrupts are rate limited, so
don't cause a burden to the CPU.

Change-ID: Iba4616d2a71288672a5f08e4512e2704b97335e8
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.

Fixes:

> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.

Fixes: f6f6424b ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inline functions are preferred over macros when they can be used
interchangeably.

CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a little more state context to an NVM update debug message.

Change-ID: I512160259052bcdbe5bdf1adf403ab2bf7984970
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Decoding the AQ return code is great except when the AQ send timed out
and there's no return code set.  This changes the handy decoder
interface to help catch and properly report the condition as a useful
errno rather than returning a misleading '0'.

Change-ID: I07a1f94f921606da49ffac7837bcdc37cd8222eb
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Only poll on the NVM semaphore if there's time left on a previous
reservation.  Also, add a little more info to debug messages.

Change-ID: I2439bf870b95a28b810dcb5cca1c06440463cf8a
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The state transitions after an error were not managed well, so
these changes get us back to the INIT state or don't transition
out of the INIT state after most errors.

Change-ID: I90aa0e4e348dc4f58cbcdce9c5d4b7fd35981c6c
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't bother trying to set a smaller timeout on the polling,
just simplify the code and always use the max limit.  Also,
rename a variable for clarity and fix a comment.

Change-ID: I0300c3562ccc4fd5fa3088f8ae52db0c1eb33af5
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>