The S3C I2C driver defaults to a rather low 66kHz, ask for 400kHz for
a bit of a speed boost.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The gpio_base for the PMIC on the CPU module was being incorrectly set to
be the same as that for the CODEC causing the two GPIO drivers to collide.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch moves SoC header files for supporting each SoCs to
plat-samsung directory. This is required to make one plat-
directory for Samsung SoCs.

Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The Lowland system is a combination of the Cragganmore CPU module and the
Tomatin and Kilchomin audio modules on Glenfarclas.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

For further modules.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The Cragganmore system is modular with I2C based identification chips on
the system allowing identification of the system build. Provide a stub I2C
driver which parses the module IDs and uses them to select the appropriate
audio subsystem components to register. To avoid confusion due to having
the mini-driver in the system the driver is placed in a separate file.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Allow us to ramp VDDARM quickly by using a GPIO to signal a voltage change
instead of doing a register write.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The chip IRQ output is genuinely an IRQ output rather than /IRQ output by
default - this had been working due to an interface issue with the IRQ
controller.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

All the regulators on the system are supplied from the fixed wall supply.
While there's no functional value in telling the regulator core this it
does ensure that as a regulator maintainer I'll be exercising the supply
logic frequently.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The original Cragganmore code was submitted while new code was being
refused for mainline. This patch was unexpectedly merged upstream but
development had continued in the expectation that the code would be
resubmitted later so no split patches were maintained. This patch
synchronises that work with the recently merged driver.

The main changes are fleshing out of the PMIC and audio integration for
the system, including addition of the Dallas Dhu and Tobermory audio
modules, plus some minor updates to account for revision 2 hardware.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The Cragganmore carrier card and Banff CPU module are used on Wolfson
Microelectronics reference systems.  This initial support covers the
core system which is a fairly generic S3C6410 based design, further
patches will add support for the key features of the reference system.

The initial board bringup and therefore much of the key code was done by
Ben Dooks for Simtec, with additional work (especially around the
integration of the Wolfson devices) being done by myself.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: removed inclusion of <mach/regs-fb.h>]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>