The pxa section is indented using spaces, use tabs.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

There are several arch-specific RTC drivers that can be successfully
compiled on other platforms. Add a COMPILE_TEST dependency for those.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>

Always show there is an I2C section, like the other sections.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Maxim Semiconductor's PMIC MAX77686 has RTC IP which is
reused in the MAX77620/MAX20024 PMICs.

Add support for these devices in MAX77686 RTC driver. This
device does not have RTC alarm pending status outside of
RTC IP. The RTC IP is having separate I2C address for its
register access.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The Kconfig option for rv3029 is not mentioning any part number, explicitly
show rv3029.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The RTC entries are mostly grouped by vendor. Move the few outliers in
place.
Also, change the one occurrence of 'nxp' to 'NXP' to make all NXP
entries consistent.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This driver adds support for the PIC32 real time clock and calendar
peripheral:
	- reading and setting time
	- alarms provided by dedicated IRQ
Signed-off-by: NJoshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.

If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

DS3231 has the temperature registers with a resolution of 0.25
degree celsius.  This enables to get the value through hwmon.

	# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
	21000
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The mt6397 RTC driver can be built either when the MFD_MT6397 driver
is enabled (which selects IRQ_DOMAIN), or when compile testing.
The latter however fails without IRQ domains:

drivers/rtc/rtc-mt6397.c: In function 'mtk_rtc_probe':
drivers/rtc/rtc-mt6397.c:326:13: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
  rtc->irq = irq_create_mapping(mt6397_chip->irq_domain, res->start);

This adds an explicit dependency for the COMPILE_TEST case.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NEddie Huang <eddie.huang@mediatek.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The max77686 RTC driver now supports the max77802 RTC as
well so there's no need to have a separate driver anymore.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This driver supports the following functions:
 - reading and setting time
 - alarms when connected to an IRQ
 - reading and clearing the voltage low flags

Datasheet:
http://www.epsondevice.com/docs/qd/en/DownloadServlet?id=ID000956Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This driver supports the following functions:
 - reading and settings time
 - alarms when connected to an IRQ
 - reading and clearing the voltage low flags
 - nvram
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Introduce a device tree binding for specifying the trickle charger
configuration for ds1390.
Signed-off-by: NIvan Grimaldi <grimaldi.ivan@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add support for RTC controller found on Xilinx Zynq Ultrascale+ MPSoC
platform.
Signed-off-by: NSuneel Garapati <suneel.garapati@xilinx.com>
Acked-by: NMoritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Currently, the rtc-sa1100 and rtc-pxa drivers co-exist as rtc-pxa has a
superset of functionality. Having 2 drivers sharing the same memory
resource is not allowed by the driver model if resources are properly
declared. This problem was avoided by not adding memory resources to the
SA1100 RTC driver, but that prevents clean-up of the SA1100 driver.

This commit converts the PXA RTC to use the exported SA1100 RTC
functions. Now the sa1100-rtc and pxa-rtc devices are mutually
exclusive, so we must remove the sa1100-rtc from pxa27x and pxa3xx.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add DA9062 RTC support into the existing DA9063 RTC driver component by
using generic access tables for common register and bit mask definitions.

The following change will add generic register and bit mask support to the
DA9063 RTC. The changes are slightly complicated by requiring support for
three register sets: DA9063-AD, DA9063-BB and DA9062-AA.

The following alterations have been made to the DA9063 RTC:

- Addition of a da9063_compatible_rtc_regmap structure to hold all generic
  registers and bitmasks for this type of RTC component.
- A re-write of struct da9063 to use pointers for regmap and compatible
  registers/masks definitions
- Addition of a of_device_id table for DA9063 and DA9062 defaults
- Refactoring functions to use struct da9063_compatible_rtc accesses to
  generic registers/masks instead of using defines from registers.h
- Re-work of da9063_rtc_probe() to use of_match_node() and dev_get_regmap()
  to provide initialisation of generic registers and masks and access to
  regmap
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add driver for the RTC found on NXP LPC178x/18xx/408x/43xx devices.
The RTC provides calendar and clock functionality together with
alarm interrupt support.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Select REGMAP_MMIO to fix the following build error seen with x86_64
randconfig.

  drivers/built-in.o: In function `snvs_rtc_probe':
rtc-snvs.c:(.text+0x567730): undefined reference to `devm_regmap_init_mmio_clk'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Acked-by: NFrank Li <Frank.Li@freescale.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Multiple options depend on I2C but are already under under if I2C. Remove
those useless dependencies.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Some entries in the Kconfig are improperly indented with spaces instead of
tabs.
Also fix whitespaces in Makefile.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Currently, CONFIG_RTC_SYSTOHC uses CONFIG_RTC_HCTOSYS_DEVICE which
is originally used by CONFIG_RTC_HCTOSYS, but this rtc device has
some limiations, for example, it must be battery-backed, be able
to work with irq off and through system suspension, etc.

So add CONFIG_RTC_SYSTOHC_DEVICE used exclusively for CONFIG_RTC_SYSTOHC,
it is more lenient compared to CONFIG_RTC_HCTOSYS_DEVICE, and could
be assigned any available RTC in the system.

Default value is CONFIG_RTC_HCTOSYS_DEVICE which is "rtc0" by default.
After this patch, NTP will sync up "rtc0" by default.

Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: NXunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Driver for the on chip RTC found on Cortina's SoC Gemini.
Signed-off-by: NHans Ulli Kroll <ulli.kroll@googlemail.com>
[alexandre.belloni@free-electrons.com: use devm_request_irq() and remove
useless goto]
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

rtc-stmp3xxx depends on lib/stmp_device, select it.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add Mediatek MT6397 RTC driver
Signed-off-by: NTianping Fang <tianping.fang@mediatek.com>
Signed-off-by: NEddie Huang <eddie.huang@mediatek.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The rtc-xgene driver is only useful on X-Gene SoC.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Currently, code of Loongson-2/3 is under loongson directory and code of
Loongson-1 is under loongson1 directory. Besides, there are Kconfig
options such as MACH_LOONGSON and MACH_LOONGSON1. This naming style is
very ugly and confusing. Since Loongson-2/3 are both 64-bit general-
purpose CPU while Loongson-1 is 32-bit SoC, we rename both file names
and Kconfig symbols from loongson/loongson1 to loongson64/loongson32.

[ralf@linux-mips.org: Resolve a number of simple conflicts.]
Signed-off-by: NHuacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Kelvin Cheung <keguang.zhang@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9790/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This is a basic driver for the ultra-low-power Abracon AB x80x series of RTC
chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor/
battery charger.

[arnd@arndb.de: abx805 depends on i2c]
[alexandre.belloni@free-electrons.com: renam buffer from date to buf in abx80x_rtc_read_time()]
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ST's Low Power Controller (LPC) controls two devices; watchdog and RTC.
Only one of the devices can be used at any one time.  This is enforced
by the correlating MFD driver.  This portion of the driver-set controls
the Real Time Clock.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

RTC is present in AM43xx and DRA7xx also.  Updating the Kconfig to depend
on ARCH_OMAP or ARCH_DAVINCI
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add driver for the RTC hardware block on the Conexant CX92755 SoC, from
the Digicolor series of SoCs.  Tested on the Equinox evaluation board for
the CX92755 chip.

[akpm@linux-foundation.org: build command arrays at compile-time]
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a driver for the Dallas/Maxim DS1685-family of RTC chips.  It
supports the DS1685/DS1687, DS1688/DS1691, DS1689/DS1693, DS17285/DS17287,
DS17485/DS17487, and DS17885/DS17887 RTC chips.  These chips are commonly
found in SGI O2 and SGI Octane systems.  It was originally derived from a
driver patch submitted by Matthias Fuchs many years ago for use in
EPPC-405-UC modules, which also used these RTCs.  In addition to the
time-keeping functions, this RTC also handles the shutdown mechanism of
the O2 and Octane and acts as a partial NVRAM for the boot PROMS in these
systems.

Verified on both an SGI O2 and an SGI Octane.
Signed-off-by: NJoshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The new mvebu SoCs come with a new RTC driver. This patch adds the
support for this new IP which is currently found in the Armada 38x
SoCs.

This RTC provides two alarms, but only the first one is used in the
driver. The RTC also allows using periodic interrupts.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: NArnaud Ebalard <arno@natisbad.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3
RTC/Calendar module w/ I2C interface.

This support includes RTC time reading and setting, Alarm (1 minute
accuracy) reading and setting, and battery low detection.  The device also
supports frequency adjustment and two timers but those features are
currently not implemented in this driver.  Due to alarm accuracy
limitation (and current lack of timer support in the driver), UIE mode is
not supported.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As we removed all the !DT boards during 3.19 cycle, we can now remove these
options.
Reported-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Support for keyword 'boolean' will be dropped later on.

No functional change.

Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.comSigned-off-by: NChristoph Jaeger <cj@linux.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

Add support for the watchdog functionality of the DS1374 rtc.  Based on
the m41t80 watchdog functionality Note: watchdog uses the same registers
as alarm.

[akpm@linux-foundation.org: don't forget mutex_unlock() in ds1374_wdt_open() error path]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NSoeren Andersen <san@rosetechnology.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>