Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch moves the contents of arch/arm/mach-mx5 to arch/arm/mach-imx
and adjusts the Makefile/Kconfig entries in a way that it's possible
to compile i.MX5 together with i.MX3/6.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>

Also, add handle_irq callbacks to machine descriptors.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

There are several occurences where MXC_INTERNAL_IRQ is
assumed to be the start of the gpio interrupts. It was never
meant this way. Replace these with gpio_to_irq.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NFabio Estevam <fabio.estevam@freescale.com>

The patch makes necessary changes on gpio-mxc as below to turn it
into an upstanding gpio driver.

 * Add a list to save all mx2 ports references, so that
   mx2_gpio_irq_handler can walk through all interrupt status
   registers

 * Use readl/writel to replace mach-specific accessors
   __raw_readl/__raw_writel

 * Change mxc_gpio_init into mxc_gpio_probe function

 * Move "struct mxc_gpio_port" into gpio-mxc.c, as it needs not to
   be public at all, and also make some other cleanup on
   plat-mxc/include/mach/gpio.h at the same time

And the patch then migrates mach-imx and mach-mx5 to the updated
driver by adding corresponding platform devices.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

mxc_board_init is too generic to be useful.  Additionally change some
mxc_timer to ${machine}_timer, too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This used to be done in .map_io which is supposed to only setup the
memory mapping.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NDaiane Angolini <daiane.angolini@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add support for dynamical allocation of imx-keypad on mx5 platform.

After moving to dynamically registration of the keypad, the keypad clock
name needs to change accordingly.

The reason is that the original mx5 keypad platform_device id was 0,
now we use id=-1 as per arch/arm/plat-mxc/devices/platform-imx-keypad.c.

Tested keypad successfully on a MX51_3DS board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This iomux file has been constructed from the Freescale pinmux tool.
It contains all pins from the tool, but the datasheet lists some
configurations not present in the tool, these are not yet added.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

PHYS_OFFSET may become a variable once the runtime PHYS_OFFSET
patch is merged, so use MX51_PHYS_OFFSET for boot_params.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add support for esdhc on mx51_3ds board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.

The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.

The various declarations were removed using the following script:

  grep -rl MACHINE_START arch/arm | xargs \
  sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'

[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

A 2M bytes SPI NOR flash(sst25vf016b) is soldered on the mx51_3ds
board.  So add the corresponding device for it.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add keymaps and imx_keypad device registration for imx51_3ds board.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

3-stack is a reference board from Freescale for their i.MX51 SoC.

Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.

Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>