Allows hookup via normal consumer mechanisms.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allows hookup via normal consumer mechanisms.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Also simplify the error handling to start unwind from the place
regulator_register fails.

No need to check rdev[i] is NULL or not before calling regulator_unregister.
regulator_unregister is safe if rdev is NULL,
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Also simplify the error handling to start unwind from the place
regulator_register fails.

No need to check rdev[i] is NULL or not before calling regulator_unregister.
regulator_unregister is safe if rdev is NULL,
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

All the drivers that need delay for the regulator voltage output voltage to
stabilize after being enabled or after being set to a new value has been
converted to implement enable_time and set_voltage_time_sel callbacks.
Then regulator core will take care of the necessary delay.

For the drivers that don't need the delay, don't need to include linux/delay.h.
This patch removes the unneeded include of linux/delay.h in regulator drivers.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since commit 8ac0e95d "regulator: core: Support setting suspend_[mode|voltage]
if set_suspend_[en|dis]able is NULL", now the regulator core can properly
handle the case set_suspend_enable callback is NULL.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If is_enabled callback is not implemented, the core assumes that the regulator
is on.

This is simpler than having a hack to retrun 1 in max8997_reg_is_enabled() if
max8997_get_enable_register() returns -EINVAL.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Integer division may truncate the result.
Use DIV_ROUND_UP to ensure new voltage setting falls within specified range.

Also properly handle the case min_vol < desc->min to ensure we don't return
negative value for selector.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

strict_strtol is deprecated and results in a checkpatch warning.
Replace it with kstrtol.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

commit 4ca1e1d9 "regulator: Convert 88pm8607 to set_voltage_sel" accidentally
changed the value writing to vol_reg.
What we want is to write val instead of selector to vol_reg.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Also rename get_current_limit and set_current_limit callbacks
to max8997_get_current_limit and max8997_set_current_limit for
better readability.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This reverts commit 98d8618a as it
breaks the build of the muic driver.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

commit 4d26f7 "regulator: max8660: Use devm_kzalloc()" missed to
replace kzalloc by devm_kzalloc. Fix it.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add irq domain support for max8997 interrupts. The reverse mapping method
used is linear mapping since the sub-drivers of max8997 such as regulator
and charger drivers can use the max8997 irq_domain to get the linux irq
number for max8997 interrupts. All uses of irq_base in platform data and
max8997 driver private data are removed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

There's no need to implement set_voltage() as there is only a very small
range of selectors for the regulators in the WM8994 and the voltages are
not expected to vary frequently at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds device tree support for dialog regulators
Signed-off-by: NYing-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since the twlreg_grp helper function is there, use it.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Let regulator core do the necessary delay for us.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

commit c172708d "regulator: core: Use a struct to pass in regulator runtime
configuration" changed the regulator_register() API signature.

Update the Documentation accordingly to reflect the change in the function
signature.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We don't support missing configs at all so segfaulting isn't that bad
but since we've got checks in the code move the dereference after them.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

commit 268a1 "regulator: twl-regulator: Use DIV_ROUND_UP at appropriate places"
introduced an off-by-one bug for setting vsel.

The linear calculation code in twl6030smps_list_voltage() does subtract index
by 1 so we need the vsel++ after DIV_ROUND_UP.

The original code use this trick to differentiate if we are going to set the
voltage to 0 or the voltage falls within the linear calculation range.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch makes the code easier to read.

Also add checking the case when no desc id is matched. This is required because
if no desc id is matched, the poiner info is pointed to twl_of_match[i].data
which may be not NULL. Checking info is NULL or not latter does not catch the
error.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>