This is to force ath6kl to power off hardware during suspend even if
sdio support keep power. This is needed, for example, when sdio
controller is buggy or maximum powersaving is desired.

Usage:

insmod ath6kl.ko suspend_cutpower=1
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If sdio controller doesn't support keep power, cut power from hardware
during suspend and restart firmware during resume. If we are connected
during suspend, send a disconnected event to user space.

Earlier suspend failed with an error if sdio didn't support keep power.
Now suspend will happen succesfully even with that case.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This way it's easier to track state changes and in the future add
more warnings about using hardware in wrong states. Currently there
are few random flags for trying to do the same, those will be cleaned
and removed in the future.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is in preparation for cutpower suspend feature. HIF layer makes
the decision based on information provided by cfg80211 and what hardware
actually supports. Then it calls ath6kl_cfg80211_suspend() to enable
the chosen mode.

Functionality should be the same, this is just preparation for
more suspend modes (cutpower and wow).
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently firmware crash dump is printed only if debug is enabled.
Change it so that the crash dump is always printed.

Also move the code from init.c to hif.c.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The benefit from this is that user space can control hardware's power state
by putting interface up and down. This is handy if firmware gets to some
weird state.

The downside will be that putting interface up takes a bit longer,
I was measuring ~500 ms during interface up.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Even though only a single concurrent remain-on-channel operation is
supported, there may be two pending remain-on-channel events (one to
indicate end of a canceled operation and another to indicate start of a
new operation). User space won't be able to distinguish these events
unless unique cookies are used.

The previous behavior resulted in wpa_supplicant getting quite
confused about the driver's offchannel state in various sequences
and this made the P2P state machine behave incorrectly. Use of
more than a single remain-on-channel cookie value fixes this.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As htc is the only user there's no reason to keep it in main.c.

No functional changes.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Also rename cred_dist_cntxt to credit_info in struct htc_target.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Remove the wdev reference in struct ath6kl.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This option lets operate more than one vif in normal mode (AP/STA/IBSS)
when support for multiple vif is enabled. This modparam needs to be used
as

modprobe ath6kl multi_norm_if_support=1
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch removes all references to ar->vif and takes
vif from a list.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use this spinlock to protect the vif's data instead of
one from ath6kl.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

WMI ready event gives the mac address, cache this
mac address in struct ath6kl so that it can be used to
compute the mac address for other vif in case of multi vif.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Interface index is passed in wmi data header as well, use it
to get the corresponding vif structure.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

So that the deinitialization of ath6kl and vif are separated.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Pass vif structure to those functions instead of ath6kl because these
functions do vif specific information initialization.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use one which is available in vif structure instead.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Interface index is passed in wmi command header from target.
Use this index to get the appropriate vif.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Pass this index to target in wmi commands to specify the interface
for which the command needs to be handled.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently ar->flag maintains interface stats. Move interface
specific states from ar->flag to vif->flags.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

vif specific information need to be moved from struct ath6kl.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This refactoring is done in a manner that it can be used
for multiple virtual interface.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to avoid using ar->wdev to get wiphy pointer, this
may need further cleanup for multi vif support.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For some reason firmware is sending invalid rates when we try to
query current bitrate from ath6kl_get_station() and a warning is issued:

[ 3810.415720] ath6kl: invalid rate: 1935633515
[ 3811.105493] ath6kl: invalid rate: 1935633515
[ 3811.556063] ath6kl: invalid rate: 1935633515

As the warning happens way too often, convert the warning to a debug
message once we have a proper fix. But to make it easy to follow
how often the problem appears, add a debugfs to print
various statistics about workarounds and make this issue the first WAR.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In some firmware versions their patch address has changed. If the firmware
provides one, use it to override the default address.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now that we allow the first Beacon frame after each connection to
be processed at the host, we can figure out the DTIM period and
expose it with Beacon interval through STA info BSS parameters
to user space.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>