Determine the VHT channel from the AP's VHT operation IE
(if present) and configure the hardware to that channel
if it is supported. If channel contexts cause a channel
to not be usable, try a smaller bandwidth.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add definitions for the VHT MCS support values that
are used to indicate, for each number of streams
(1 through 8) which MCSes are supported.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NMarco Porsch <marco.porsch@etit.tu-chemnitz.de>
[prefix with IEEE80211_]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Introduce IEEE80211_NUM_TIDS in the generic 802.11
header file and use it in place of STA_TID_NUM and
NUM_RX_DATA_QUEUES which are both really the number
of TIDs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The Peer-to-Peer IE is vendor-specific IE identified by WiFi Alliance
OUI and specific P2P OUI type. The payload of this IE consists of
so-called P2P attributes. This patch adds definitions for processing
these attributes.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The BCM4706 has two PCIe host controller on the bcma bus. For PCIe
client mode it is assumed that there is only one PCIe controller so the
PCIe driver, like b43 and brcmsmac are accessing the first PCIe
controller when they want to issue a operation on the host controller.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a preparing step for adding serial flash support.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are some devices which are able to boot from nand flash and other
are using a serial flash for booting. Add a bool to indicate that the
device is booted from that flash chip and not from some other chip also
connected to the SoC. This is needed to find the nvram, as it is stored
on the flash the devices booted from.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some parts of the initialization for chip common and the pcie core are
accessing the sprom struct, but it is not initialized at that stage.
Just do the necessary thing in the early register on SoCs and not the
complete initialization to read out the nvram from the flash chip.
After it is possible to read out the nvram, the sprom should be parsed
from it and the full initialization of the cores should be run.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WLAN_EID_WPA and WLAN_EID_GENERIC mapped to the same value
as WLAN_EID_VENDOR_SPECIFIC. The last one being more in line
with the standard specification. Removing WLAN_EID_WPA and
WLAN_EID_GENERIC as there are no longer drivers using these.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Rename struct ieee80211_vht_capabilities to ieee80211_vht_cap
and renamed its member vht_capabilities_info to vht_cap_info.
Signed-off-by: NMahesh Palivela <maheshp@posedge.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

It seems that was linux/blk_types.h incorrectly exported to fix up some missing
bits required by the exported parts of linux/fs.h (READ, WRITE, READA, etc.).

So unexport linux/blk_types.h and unexport the relevant bits of linux/fs.h.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Jens Axboe <jaxboe@fusionio.com>
cc: Tejun Heo <tj@kernel.org>
cc: Al Viro <viro@ZenIV.linux.org.uk>

Unexport part of linux/ppp-comp.h as userspace can't make use of that bit.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Paul Mackerras <paulus@samba.org>
cc: David Miller <davem@davemloft.net>

In the common case where a name is much smaller than PATH_MAX, an extra
allocation for struct filename is unnecessary. Before allocating a
separate one, try to embed the struct filename inside the buffer first. If
it turns out that that's not long enough, then fall back to allocating a
separate struct filename and redoing the copy.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Keep a pointer to the audit_names "slot" in struct filename.

Have all of the audit_inode callers pass a struct filename ponter to
audit_inode instead of a string pointer. If the aname field is already
populated, then we can skip walking the list altogether and just use it
directly.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

...and fix up the callers. For do_file_open_root, just declare a
struct filename on the stack and fill out the .name field. For
do_filp_open, make it also take a struct filename pointer, and fix up its
callers to call it appropriately.

For filp_open, add a variant that takes a struct filename pointer and turn
filp_open into a wrapper around it.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Currently, if we call getname() on a userland string more than once,
we'll get multiple copies of the string and multiple audit_names
records.

Add a function that will allow the audit_names code to satisfy getname
requests using info from the audit_names list, avoiding a new allocation
and audit_names records.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

getname() is intended to copy pathname strings from userspace into a
kernel buffer. The result is just a string in kernel space. It would
however be quite helpful to be able to attach some ancillary info to
the string.

For instance, we could attach some audit-related info to reduce the
amount of audit-related processing needed. When auditing is enabled,
we could also call getname() on the string more than once and not
need to recopy it from userspace.

This patchset converts the getname()/putname() interfaces to return
a struct instead of a string. For now, the struct just tracks the
string in kernel space and the original userland pointer for it.

Later, we'll add other information to the struct as it becomes
convenient.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

* allow kernel_execve() leave the actual return to userland to
caller (selected by CONFIG_GENERIC_KERNEL_EXECVE).  Callers
updated accordingly.
* architecture that does select GENERIC_KERNEL_EXECVE in its
Kconfig should have its ret_from_kernel_thread() do this:
	call schedule_tail
	call the callback left for it by copy_thread(); if it ever
returns, that's because it has just done successful kernel_execve()
	jump to return from syscall
IOW, its only difference from ret_from_fork() is that it does call the
callback.
* such an architecture should also get rid of ret_from_kernel_execve()
and __ARCH_WANT_KERNEL_EXECVE

This is the last part of infrastructure patches in that area - from
that point on work on different architectures can live independently.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The con_debug_leave/con_debug_enter functions are stubbed out
by defining them to (0), which causes harmless build warnings.
Using proper inline functions is the normal way to deal with
this.

Without this patch, building the ARM bcm2835_defconfig results in:

drivers/tty/serial/kgdboc.c: In function 'kgdboc_pre_exp_handler':
drivers/tty/serial/kgdboc.c:279:3: warning: statement with no effect [-Wunused-value]
drivers/tty/serial/kgdboc.c: In function 'kgdboc_post_exp_handler':
drivers/tty/serial/kgdboc.c:293:3: warning: statement with no effect [-Wunused-value]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

First, it's incorrect to call putname() after __getname_gfp() since the
bare __getname_gfp() call skips the auditing code, while putname()
doesn't.

mount_block_root allocates a PATH_MAX buffer via __getname_gfp, and then
calls get_fs_names to fill the buffer. That function can call
get_filesystem_list which assumes that that buffer is a full page in
size. On arches where PAGE_SIZE != 4k, then this could potentially
overrun.

In practice, it's hard to imagine the list of filesystem names even
approaching 4k, but it's best to be safe. Just allocate a page for this
purpose instead.

With this, we can also remove the __getname_gfp() definition since there
are no more callers.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

In order to accomodate retrying path-based syscalls, we need to add a
new "type" argument to audit_inode_child. This will tell us whether
we're looking for a child entry that represents a create or a delete.

If we find a parent, don't automatically assume that we need to create a
new entry. Instead, use the information we have to try to find an
existing entry first. Update it if one is found and create a new one if
not.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Currently, this gets set mostly by happenstance when we call into
audit_inode_child. While that might be a little more efficient, it seems
wrong. If the syscall ends up failing before audit_inode_child ever gets
called, then you'll have an audit_names record that shows the full path
but has the parent inode info attached.

Fix this by passing in a parent flag when we call audit_inode that gets
set to the value of LOOKUP_PARENT. We can then fix up the pathname for
the audit entry correctly from the get-go.

While we're at it, clean up the no-op macro for audit_inode in the
!CONFIG_AUDITSYSCALL case.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

For now, we just have two possibilities:

UNKNOWN: for a new audit_names record that we don't know anything about yet
NORMAL: for everything else

In later patches, we'll add other types so we can distinguish and update
records created under different circumstances.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Most of the callers get called with an inode and dentry in the reverse
order. The compiler then has to reshuffle the arg registers and/or
stack in order to pass them on to audit_inode_child.

Reverse those arguments for a micro-optimization.
Reported-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

__attribute__((error(msg))) was introduced in gcc 4.3 (not 4.4) and as I
was unable to find any gcc bugs pertaining to it, I'm presuming that it
has functioned as advertised since 4.3.0.
Signed-off-by: NDaniel Santos <daniel.santos@pobox.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Tested-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

Some device types support a form of power management in which
the device suggests to the host that the device may be suspended
now. Support for that is best located in usbnet.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VXLAN bases source UDP port based on flow to help the
receiver to be able to load balance based on outer header flow.

This patch restricts the port range to the normal UDP local
ports, and allows overriding via configuration.

It also uses jhash of Ethernet header when looking at flows
with out know L3 header.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The !CONFIG_OF stubs aren't static so if multiple files include the
header with this configuration then the linker will see multiple
definitions of the stubs.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e1aab161 ("socket: initial cgroup code.") causes a build
error when CONFIG_INET is disabled in Linus' tree:

  net/built-in.o: In function `sk_update_clone':
  net/core/sock.c:1336: undefined reference to `sock_update_memcg'

sock_update_memcg() is only defined when CONFIG_INET is enabled, so fix
it by defining the dummy function without this option.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The resource index for the mailboxes was incorrect.
Signed-off-by: NChad Reese <kreese@caviumnetworks.com>
Acked-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Address comments provided by Andrew Morton:
https://lkml.org/lkml/2012/10/3/550

 - Keeps consistent kerneldoc compatible comments style for new static
   functions.
 - Removes unnecessary complexity from destination ID allocation
   routine.
 - Uses kcalloc() for code clarity.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

{get,clear,set}_pageblock_skip() use incorrect bit ranges (please compare
to bit ranges used by {get,set}_pageblock_flags() used for migration
types) and can overwrite pageblock migratetype of the next pageblock in
the bitmap.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMel Gorman <mgorman@suse.de>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NMinchan Kim <minchan@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>