If possible that after suspend, cfg80211 will receive request to
disconnect what require action on interface that was removed during
suspend.

Problem can manifest itself by various warnings similar to below one:

WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]()
wlan0:  Failed check-sdata-in-driver check, flags: 0x4
Call Trace:
 [<c043e0b3>] warn_slowpath_fmt+0x33/0x40
 [<f83707c9>] ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]
 [<f83a660a>] ieee80211_recalc_ps_vif+0x2a/0x30 [mac80211]
 [<f83a6706>] ieee80211_set_disassoc+0xf6/0x500 [mac80211]
 [<f83a9441>] ieee80211_mgd_deauth+0x1f1/0x280 [mac80211]
 [<f8381b36>] ieee80211_deauth+0x16/0x20 [mac80211]
 [<f8261e70>] cfg80211_mlme_down+0x70/0xc0 [cfg80211]
 [<f8264de1>] __cfg80211_disconnect+0x1b1/0x1d0 [cfg80211]

To fix the problem disconnect from any associated network before
suspend. User space is responsible to establish connection again
after resume. This basically need to be done by user space anyway,
because associated stations can go away during suspend (for example
NetworkManager disconnects on suspend and connect on resume by default).

Patch also handle situation when driver refuse to suspend with wowlan
configured and try to suspend again without it.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is another case of data increasing the size of the
wiphy information significantly with a new feature, for
now remove this as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When drivers or regulatory have limitations on
40, 80 or 160 MHz channels, advertise these to
userspace via nl80211. Also add a new feature
flag to let userspace know this is supported.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add new NL80211_CMD_RADAR_DETECT, which starts the Channel
Availability Check (CAC). This command will also notify the
usermode about events (CAC finished, CAC aborted, radar
detected, NOP finished).
Once radar detection has started it should continuously
monitor for radars as long as the channel is active.

This patch enables DFS for AP mode in nl80211/cfg80211.

Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
[remove WIPHY_FLAG_HAS_RADAR_DETECT again -- my mistake]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This prepares for using the spinlock instead of krefs
which is needed in the next patch to track the refs
of combined BSSes correctly.

Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.

An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.

Black- and whitelists are supported, but not simultaneously.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since:

commit 2c60db03
Author: Eric Dumazet <edumazet@google.com>
Date:   Sun Sep 16 09:17:26 2012 +0000

    net: provide a default dev->ethtool_ops

wireless core does not correctly assign ethtool_ops.

After alloc_netdev*() call, some cfg80211 drivers provide they own
ethtool_ops, but some do not. For them, wireless core provide generic
cfg80211_ethtool_ops, which is assigned in NETDEV_REGISTER notify call:

        if (!dev->ethtool_ops)
                dev->ethtool_ops = &cfg80211_ethtool_ops;

But after Eric's commit, dev->ethtool_ops is no longer NULL (on cfg80211
drivers without custom ethtool_ops), but points to &default_ethtool_ops.

In order to fix the problem, provide function which will overwrite
default_ethtool_ops and use it by wireless core.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is pretty much useless since get_wiphy_idx()
always returns true since it's always called with
a valid wiphy pointer.
Acked-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The commit:

commit 5e760230
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Nov 4 11:18:17 2011 +0100

    cfg80211: allow registering to beacons

allowed only a single process to register for beacon events
per wiphy.  This breaks cases where a user may want two or
more VIFs on a wiphy and run a seperate hostapd process on
each vif.

This patch allows multiple beacon listeners, fixing the
regression.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These were missed due to the tracing work having
started on a kernel that didn't have P2P Device
yet, implement them now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

No driver initializes chan->max_antenna_gain to something sensible, and
the only place where it is being used right now is inside ath9k. This
leads to ath9k potentially using less tx power than it can use, which can
decrease performance/range in some rare cases.

Rather than going through every single driver, this patch initializes
chan->orig_mag in wiphy_register(), ignoring whatever value the driver
left in there. If a driver for some reason wishes to limit it independent
from regulatory rulesets, it can do so internally.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow adding central tracing like in mac80211.
Signed-off-by: NHila Gonen <hila.gonen@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add an NL80211_SCAN_FLAG_FLUSH flag that causes old bss cache
entries to be flushed on scan completion. This is useful for
collecting guaranteed fresh scan/survey result (e.g. on resume).

For normal scan, flushing only happens on successful completion
of a scan; i.e. it does not happen if the scan is aborted.
For scheduled scan, previous scan results are flushed everytime
when we get new scan results.

This feature is enabled by default. Drivers can disable it by
unsetting the NL80211_FEATURE_SCAN_FLUSH flag.
Signed-off-by: NSam Leffler <sleffler@chromium.org>
Tested-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
[invert polarity of feature flag to account for old kernels]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.

This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.

Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.

As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

libertas currently calls cfg80211_disconnected() when it is being
brought down. This causes an event to be allocated, but since the
wdev is already removed from the rdev by the time that the event
processing work executes, the event is never processed or freed.
http://article.gmane.org/gmane.linux.kernel.wireless.general/95666

Fix this leak, and other possible situations, by processing the event
queue when a device is being unregistered. Thanks to Johannes Berg for
the suggestion.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Cc: stable@vger.kernel.org
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we have wiphy_regulatory_register() we can
tuck away the core's regulatory_update() call there
and make it static.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This makes it clearer what we're doing. This now makes a bit
more sense given that regardless of the wiphy if the cell
base station hint feature is supported we will be modifying the
way the regulatory core behaves.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Cellular base stations can provide hints to cfg80211 about
where they think we are. This can be done for example on
a cell phone. To enable these hints we simply allow them
through as user regulatory hints but we allow userspace
to clasify the hint as either coming directly from the
user or coming from a cellular base station. This option
is only available when you enable
CONFIG_CFG80211_CERTIFICATION_ONUS.

The base station hints themselves will not be processed
by the core unless at least one device on the system
supports this feature.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Revert commit b78e8cea
("cfg80211: track monitor channel") and remove the
set_monitor_enabled() callback.

Due to the tracking happening in NETDEV_PRE_UP, it had
introduced bugs because the monitor interface callback
would be called before the device was started. It looks
like there's no way to fix this, and using NETDEV_PRE_UP
is broken anyway (since there's no NETDEV_UP_FAIL), so
remove all that code, track interfaces in NETDEV_UP and
also stop tracking the monitor channel in cfg80211.

This mostly reverts to before the tracking, except that
we keep the interface count tracking so that setting the
monitor channel can be rejected properly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a few places that iterate the wdev
list and assume wdev->netdev exists, check
there. The rfkill one has to be extended for
each non-netdev type later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to support a P2P device abstraction and
Bluetooth high-speed AMPs, we need to have a way
to identify virtual interfaces that don't have a
netdev associated.

Do this by adding a NL80211_ATTR_WDEV attribute
to identify a wdev which may or may not also be
a netdev.

To simplify things, use a 64-bit value with the
high 32 bits being the wiphy index for this new
wdev identifier in the nl80211 API.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Quick fix for method being invoked without checking its existence.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Michal's monitor channel tracking introduce a locking problem
as it locked the rdev lock inside the netdev notifier which
isn't allowed as we might already hold it if we get there by
removing an interface that is up.

Fix this by relying only on the RTNL to protect the interface
counters, the RTNL is always held in these code paths anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.

Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

devlist_mtx locking is changed to accomodate changes.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

.connect cannot be handled since the driver scans
and connects on its own. It is up to the driver
then to refuse a connection (with -EBUSY for
example).

Non-fixed channel IBSSes always take a single
channel resource. For example two non-fixed
channel IBSSes always take up 2
num_different_channels, even if they operate on
the same channel at a given point of time.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implements behaviour seen in mac80211. A running
monitor always has a channel - even before
.set_channel. This way we won't break current
behaviour.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make it even more obvious we support single
monitor channel. This will allow us to remove
.get_channel.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implements .set_monitor_enabled(wiphy, enabled).

Notifies driver upon change of interface layout.

If only monitor interfaces become present it is
called with 2nd argument being true. If
non-monitor interface appears then 2nd argument
is false. Driver is notified only upon change.

This makes it more obvious about the fact that
cfg80211 supports single monitor channel. Once we
implement multi-channel we don't want to allow
setting monitor channel while other interface
types are running. Otherwise it would be ambiguous
once we start considering num_different_channels.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We'll need this for proper channel tracking (which
is going to be needed for channel context
accounting and finding matching/active interface
combination).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.

Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some of the functions to retrieve a device can
be static as they're used only in nl80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fixed some checkpatch warnings.
Signed-off-by: NCristian Chilipirea <cristian.chilipirea@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My grand plan to allow drivers to gradually move over
to advertising virtual interface combinations and only
enforce with drivers that do want it enforced doesn't
seem to be working out, only Christian ever added the
advertising (to carl9170), nobody else did.

Begin enforcing combinations in cfg80211 so that users
can rely on the information reported about a device.

Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.

Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.

Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.
Signed-off-by: NSven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not call ->suspend, ->resume methods after we unregister wiphy. Also
delete sta_clanup timer after we finish wiphy unregister to avoid this:

WARNING: at lib/debugobjects.c:262 debug_print_object+0x85/0xa0()
Hardware name: 6369CTO
ODEBUG: free active (active state 0) object type: timer_list hint: sta_info_cleanup+0x0/0x180 [mac80211]
Modules linked in: aes_i586 aes_generic fuse bridge stp llc autofs4 sunrpc cpufreq_ondemand acpi_cpufreq mperf ext2 dm_mod uinput thinkpad_acpi hwmon sg arc4 rt2800usb rt2800lib crc_ccitt rt2x00usb rt2x00lib mac80211 cfg80211 i2c_i801 iTCO_wdt iTCO_vendor_support e1000e ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom yenta_socket ahci libahci pata_acpi ata_generic ata_piix i915 drm_kms_helper drm i2c_algo_bit video [last unloaded: microcode]
Pid: 5663, comm: pm-hibernate Not tainted 3.1.0-rc1-wl+ #19
Call Trace:
 [<c0454cfd>] warn_slowpath_common+0x6d/0xa0
 [<c05e05e5>] ? debug_print_object+0x85/0xa0
 [<c05e05e5>] ? debug_print_object+0x85/0xa0
 [<c0454dae>] warn_slowpath_fmt+0x2e/0x30
 [<c05e05e5>] debug_print_object+0x85/0xa0
 [<f8a808e0>] ? sta_info_alloc+0x1a0/0x1a0 [mac80211]
 [<c05e0bd2>] debug_check_no_obj_freed+0xe2/0x180
 [<c051175b>] kfree+0x8b/0x150
 [<f8a126ae>] cfg80211_dev_free+0x7e/0x90 [cfg80211]
 [<f8a13afd>] wiphy_dev_release+0xd/0x10 [cfg80211]
 [<c068d959>] device_release+0x19/0x80
 [<c05d06ba>] kobject_release+0x7a/0x1c0
 [<c07646a8>] ? rtnl_unlock+0x8/0x10
 [<f8a13adb>] ? wiphy_resume+0x6b/0x80 [cfg80211]
 [<c05d0640>] ? kobject_del+0x30/0x30
 [<c05d1a6d>] kref_put+0x2d/0x60
 [<c05d056d>] kobject_put+0x1d/0x50
 [<c08015f4>] ? mutex_lock+0x14/0x40
 [<c068d60f>] put_device+0xf/0x20
 [<c069716a>] dpm_resume+0xca/0x160
 [<c04912bd>] hibernation_snapshot+0xcd/0x260
 [<c04903df>] ? freeze_processes+0x3f/0x90
 [<c049151b>] hibernate+0xcb/0x1e0
 [<c048fdc0>] ? pm_async_store+0x40/0x40
 [<c048fe60>] state_store+0xa0/0xb0
 [<c048fdc0>] ? pm_async_store+0x40/0x40
 [<c05d0200>] kobj_attr_store+0x20/0x30
 [<c0575ea4>] sysfs_write_file+0x94/0xf0
 [<c051e26a>] vfs_write+0x9a/0x160
 [<c0575e10>] ? sysfs_open_file+0x200/0x200
 [<c051e3fd>] sys_write+0x3d/0x70
 [<c080959f>] sysenter_do_call+0x12/0x28

Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>