Implement atomic kernel mode settings using the fb layer's debug hook
system for supporting debugger interaction.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

At module unload time we'll tear down the fbdev state.  We do so under
the struct mutex, so we shouldn't try to use the unlocked variant of
the GEM object unreference function or we may deadlock.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

This fixes a potential modesetting error during boot with plymouth on
Broadwater and Crestline introduced with 9df47c. The framebuffer was
hard-coding an alignment of 64K, but the modesetting code required the
documented alignment of 128K. The result was that we would attempt to
unbind the pinned fbcon buffer, triggering an ERROR and ultimately
failing the mode change.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

The previous commit fixes the problem, these commits make sure we actually
fail properly if it happens again.

I've squashed the commits from Chris since they are all fixing one issue.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

(regression fix since fbdev/kms rework).

My fb rework didn't remember about the 84/65s.
Reported-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.

v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.

v3: add config lock take inside polling, add intel/nouveau poll init/fini calls

v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.

glisse: discard drm_helper_hpd_irq_event

v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Just preparation, no functional change.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch is against the drm-fbdevfix1 branch. It removes the
drm_fb_helper_setcolreg function. The reason is that fb_setcolreg is only
used in the case where fb_setcmap is called and no fb_ops->fb_setcmap is
used. In the drm case we always need a fb_setcmap hook to handle multiple
crtcs so we don't need a fb_setcolreg hook. Please apply.
Signed-off-by: NJames Simmons <jsimmons@infradead.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

a) slow work is always used now for any fbcon hotplug, as its not
   a fast task and is more suited to being ran under slow work.

b) attempt to not do any fbdev changes when X is running as we'll
   just mess it up. This hooks set_par to hopefully do the changes
   once X hands control to fbdev.

This also adds the nouveau/intel hotplug support.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This breaks the connection between the core drm connector list
and the fbdev connector usage, and allows them to become disjoint
in the future. It also removes the untype void* that was in the
connector struct to support this.

All connectors are added to the fbdev now but this could be
changed in the future.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This move to using the list of crtcs in the fb helper and cleans up the
whole picking code, now we store the crtc/connectors we want directly
into the modeset and we use the modeset directly to set the mode.

Fixes from James Simmons and Ben Skeggs.
Signed-off-by: NDave Airlie <airlied@redhat.com>

The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.

This patch

a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: NDave Airlie <airlied@redhat.com>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

This is a purely cosmetic change to make changes in this area easier.
And hey, it's not only clearer and typechecked, but actually shorter,
too!

[anholt: To clarify, this is a change to let us later make
drm_i915_gem_object subclass drm_gem_object, instead of having
drm_gem_object have a pointer to i915's private data]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.

4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia -  - use _DSM ACPI method.

TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.

v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.

v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.

v4: ATPX msg handling using buffers - should work on more machines

v5: rearchitect after more mjg59 discussion - move ATPX handling to
    radeon driver.

v6: add file headers + initial nouveau bits (to be filled out).

v7: merge delayed switcher code.

v8: avoid suspend/resume of gpu that is off

v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling

v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv

v11: fix bug in resuming Intel for 2nd time.

v12: start fixing up nvidia code blindly.

v13: blindly guess at finishing nvidia code

v14: remove radeon audio hacks - fix up intel resume more like upstream

v15: clean up printks + remove unnecessary igd/dis pointers

mount debugfs

/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
 + 2 cards.

DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use

Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: NDave Airlie <airlied@redhat.com>

An untiled framebuffer must be aligned to 64k. This is normally handled
by intel_pin_and_fence_fb_obj(), but the intelfb_create() likes to be
different and do the pinning itself. However, it aligns the buffer
object incorrectly for pre-i965 chipsets causing a PGTBL_ERR when it is
installed onto the output.

Fixes:
  KMS error message while initializing modesetting -
  render error detected: EIR: 0x10 [i915]
  http://bugs.freedesktop.org/show_bug.cgi?id=22936Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: NEric Anholt <eric@anholt.net>

That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Replace the DRM_DEBUG with DRM_DEBUG_KMS in output device code.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.

this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.

Tested on r100/r600/i945.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: NDave Airlie <airlied@redhat.com>

[note this requires an fb patch posted to linux-fbdev-devel already]

This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.

video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.

The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.

video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.

The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Set accel to none, we really don't want anyone thinking
fb is an accel interface.
Pass pitch not depth to function for intel.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Initially I always meant this code to be shared, but things
ran away from me before I got to it.

This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.

It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.

radeon retains some specific codes used for a big endian
workaround.

changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Convert many printk calls to DRM_DEBUG calls to reduce kernel log noise
for normal activities. Switch other printk calls to DRM_ERROR or DRM_INFO.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

While sifting through the inteldrmfb code trying to solve #22040 I found that
the fb restore path doesn't check the return value of
drm_crtc_helper_set_config(), which seems to have all sorts of potential
failure modes. We should warn someone if one of these is triggered.
Signed-Off-By: NBen Gamari <bgamari.foss@gmail.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-applied, failures are mine]
Signed-off-by: NEric Anholt <eric@anholt.net>

With KMS we have ran into an issue where we really want the KMS fb driver
to be the one running the console, so panics etc can be shown by switching
out of X etc.

However with vesafb/efifb built-in, we end up with those on fb0 and the
KMS fb driver on fb1, driving the same piece of hw, so this adds an fb
info flag to denote a firmware fbdev, and adds a new aperture base/size
range which can be compared when the hw drivers are installed to see if
there is a conflict with a firmware driver, and if there is the firmware
driver is unregistered and the hw driver takes over.

It uses new aperture_base/size members instead of comparing on the fix
smem_start/length, as smem_start/length might for example only cover the
first 1MB of the PCI aperture, and we could allocate the kms fb from 8MB
into the aperture, thus they would never overlap.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NDave Airlie <airlied@redhat.com>
Acked-by: NPeter Jones <pjones@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

duplicate the mode into fbcon storage, so when we free modes later
we don't just lose this.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The sysrq functions are executed in hardirq context, so we shouldn't be
calling sleeping functions from them, like mutex_locks or memory
allocations.

Fix up the i915 sysrq handler to avoid this.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

Commit 79e53945 introduced a
regression where you cannot use sysrq 'g' to enter kgdb.  The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics.  The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.

This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

At the same time, bring the action message closer to the usual format.
Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

If we fail whilst constructing the fb, then we need to unpin it as well.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Fix this sparse warning:

  drivers/gpu/drm/i915/intel_fb.c:417:5: warning: symbol 'intelfb_panic' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@linux.ie>

This is required by the display plane, and fixes 1400x1050 laptop displays.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This commit adds i915 driver support for the DRM mode setting APIs.
Currently, VGA, LVDS, SDVO DVI & VGA, TV and DVO LVDS outputs are
supported.  HDMI, DisplayPort and additional SDVO output support will
follow.

Support for the mode setting code is controlled by the new 'modeset'
module option.  A new config option, CONFIG_DRM_I915_KMS controls the
default behavior, and whether a PCI ID list is built into the module for
use by user level module utilities.

Note that if mode setting is enabled, user level drivers that access
display registers directly or that don't use the kernel graphics memory
manager will likely corrupt kernel graphics memory, disrupt output
configuration (possibly leading to hangs and/or blank displays), and
prevent panic/oops messages from appearing.  So use caution when
enabling this code; be sure your user level code supports the new
interfaces.

A new SysRq key, 'g', provides emergency support for switching back to
the kernel's framebuffer console; which is useful for testing.

Co-authors: Dave Airlie <airlied@linux.ie>, Hong Liu <hong.liu@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>