Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 09 1月, 2009 10 次提交
  3. 08 1月, 2009 5 次提交
  5. 07 1月, 2009 6 次提交
  7. 01 1月, 2009 1 次提交
  9. 29 12月, 2008 9 次提交
    • Y
      Input: add support for enhanced rotary controller on pxa930 and pxa935 · e0ee6298
      由 Yong Yao 提交于 
      Signed-off-by: NYong Yao <yaoyong@marvell.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
      e0ee6298
    • Y
      Input: add support for trackball on pxa930 and pxa935 · 105ca239
      由 Yong Yao 提交于 
      Signed-off-by: NYong Yao <yaoyong@marvell.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
      105ca239
    • E
      [ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices · 198fc108
      由 Eric Miao 提交于 
      PXA27x and later processors support overlay1 and overlay2 on-top of the
base framebuffer (although under-neath the base is also possible). They
support palette and no-palette RGB formats, as well as YUV formats (only
available on overlay2). These overlays have dedicated DMA channels and
behave in a similar way as a framebuffer.

This heavily simplified and re-structured work is based on the original
pxafb_overlay.c (which is pending for mainline merge for a long time).

The major problems with this pxafb_overlay.c are (if you are interested
in the history):

  1. heavily redundant (the control logics for overlay1 and overlay2 are
     actually identical except for some small operations,  which are now
     abstracted into a 'pxafb_layer_ops' structure)

  2. a lot of useless and un-tested code (two workarounds which are now
     fixed on mature silicons)

  3. cursorfb is actually useless, hardware cursor should not be used
     this way, and the code was actually un-tested for a long time.

The code in this patch should be self-explanatory, I tried to add minimum
comments. As said, this is basically simplified, there are several things
still on the pending list:

  1. palette mode is un-supported and un-tested (although re-using the
     palette code of the base framebuffer is actually very easy now with
     previous clean-up patches)

  2. fb_pan_display for overlay(s) is un-supported

  3. the base framebuffer can actually be abstracted by 'pxafb_layer' as
     well, which will help further re-use of the code and keep a better
     and consistent structure. (This is the reason I named it 'pxafb_layer'
     instead of 'pxafb_overlay' or something alike)

See Documentation/fb/pxafb.txt for additional usage information.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: NEric Miao <ycmiao@ycmiao-hp520.(none)>
      198fc108
    • E
      [ARM] pxafb: cleanup of the color format manipulation code · 878f5783
      由 Eric Miao 提交于 
      1. introduce var_to_depth() to calculate the color depth including the
   transparency bit

2. the conversion from 'fb_var_screeninfo' to LCCR3 BPP bits can be re-
   used by overlays (in OVLxC1), thus an individual pxafb_var_to_bpp()
   has been separated out.

3. pxafb_setmode() should really set the color bitfields correctly at
   begining, introduce a pxafb_set_pixfmt() for this

4. allow user apps to specify color formats within fb_var_screeninfo,
   and checking of this in pxafb_check_var() has been simplified as
   below:

   a) pxafb_var_to_bpp() should pass - which means a basically correct
      bits_per_pixel and color depth setting
   b) the RGBT bitfields are then forced into supported values by
      pxafb_set_pixfmt()
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NEric Miao <ycmiao@ycmiao-hp520.(none)>
      878f5783
    • E
      [ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3 · a0427509
      由 Eric Miao 提交于 
      Add the palette format support for LCCR4_PAL_FOR_3, and fix the
issue of LCCR4 being never assigned.

Also remove the useless pxafb_set_truecolor().
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NEric Miao <ycmiao@ycmiao-hp520.(none)>
      a0427509
    • E
      [ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching · 6e354846
      由 Eric Miao 提交于 
      dma branching is enabled by extending the current setup_frame_dma()
function to allow a 2nd set of frame/palette dma descriptors to be
used.

As a result, pxafb_dma_buff.dma_desc[], pxafb_dma_buff.pal_desc[]
and pxafb_info.fdadr[] are doubled.

This allows maximum re-use of the current dma setup code, although
the pxafb_info.fdadr[xx] for FBRx register values looks a bit odd.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NEric Miao <ycmiao@ycmiao-hp520.(none)>
      6e354846
    • E
      [ARM] pxafb: allow video memory size to be configurable · 77e19675
      由 Eric Miao 提交于 
      The amount of video memory size is decided according to the following
order:

1. <xres> x <yres> x <bits_per_pixel> by default, which is the backward
   compatible way

2. size specified in platform data

3. size specified in module parameter 'options' string or specified in
   kernel boot command line (see updated Documentation/fb/pxafb.txt)

And now since the memory is allocated from system memory, the pxafb_mmap
can be removed and the default fb_mmap() should be working all right.

Also, since we now have introduced the 'struct pxafb_dma_buff' for DMA
descriptors and palettes, the allocation can be separated cleanly.

NOTE: the LCD DMA actually supports chained transfer (i.e. page-based
transfers), to simplify the logic and keep the performance (with less
TLB misses when accessing from memory mapped user space), the memory
is allocated by alloc_pages_*() to ensures it's physical contiguous.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NEric Miao <ycmiao@ycmiao-hp520.(none)>
      77e19675
    • E
      [ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant · 6769717d
      由 Eric Miao 提交于 
      As Nicolas and Russell pointed out, CLOCK_TICK_RATE is no more
a constant on PXA when multiple processors and platforms are
selected, change TIMER_FREQ in rtc-sa1100.c into a variable.

Since the code to decide the clock tick rate is re-used from
timer.c, introduce a common get_clock_tick_rate() for this.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NNicolas Pitre <nico@marvell.com>
      6769717d
    • E
      [ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad) · 9f1442bb
      由 Eric Miao 提交于 
      Signed-off-by: NEric Miao <eric.miao@marvell.com>
      9f1442bb
  11. 25 12月, 2008 1 次提交
  13. 24 12月, 2008 1 次提交
  15. 22 12月, 2008 3 次提交
  17. 21 12月, 2008 4 次提交