Intel Penwell chip has two 96 pins GPIO blocks, which are very similiar as
Intel Langwell chip GPIO block, except for pin number difference. This
patch expends the original Langwell GPIO driver to support Penwell's.
Signed-off-by: NAlek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Nobody uses that anymore, so remove and expect drivers to use the gpiolib
implementation.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Stop using the omap-specific implementations for gpio debouncing now that
gpiolib provides its own support.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

OMAP supports debouncing of gpio lines, implement the method using
gpiolib.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A few architectures, like OMAP, allow you to set a debouncing time for the
gpio before generating the IRQ.  Teach gpiolib about that.

Mark said:
: This would be generally useful for embedded systems, especially where
: the interrupt concerned is a wake source.  It allows drivers to avoid
: spurious interrupts from noisy sources so if the hardware supports it
: the driver can avoid having to explicitly wait for the signal to become
: stable and software has to cope with fewer events.  We've lived without
: it for quite some time, though.

David said:
: I looked at adding debounce support to the generic GPIO calls (and thus
: gpiolib) some time back, but decided against it.  I forget why at this
: time (check list archives) but it wasn't because of lack of utility in
: certain contexts.
:
: One thing to watch out for is just how variable the hardware capabilities
: are.  Atmel GPIOs have something like a fixed number of 32K clock cycles
: for debounce, twl4030 had something odd, OMAPs were more like the Atmel
: chips but with a different clock.  In some cases debouncing had to be
: ganged, not per-GPIO.  And so forth.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current message, 'not registered' is confusing as it implies it was
not registered with something, whereas printing 'failed to register'
implies it was the gpiochip_add() call that did not work correctly.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a bug I noticed while hacking on the max732x driver for interrupt
support.  According to the datasheets, open-drain pins have to be
configured as output-high (which in that case is actually high impedance)
to be used as input.
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Setup both client_group_a and client_group_b if nr_port > 8 (not including
nr_port==8).
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The valid offset value is 0..PL061_GPIO_NR-1, this patch corrects the
offset value range checking.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

gpiolib doesn't need to modify the names and I assume most initializers
use string constants that shouldn't be modified anyhow.

[akpm@linux-foundation.org: fix drivers/gpio/cs5535-gpio.c]
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most of the GPIO expanders supported by the max732x driver have interrupt
generation capability by reporting changes on input pins through an INT#
pin.  This patch implements the irq_chip functionnality (edge detection
only).
Signed-off-by: NMarc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jebediah Huang <jebediah.huang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a driver for the RTC on the AB8500 power management chip.  This is a
client of the AB8500 MFD driver.
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NSrinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use memdup_user when user data is immediately copied into the allocated
region.  Elimination of the variable ads, which is no longer useful.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Ian Kent <raven@themaw.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use memdup_user when user data is immediately copied into the
allocated region.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@

-  to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+  to = memdup_user(from,size);
   if (
-      to==NULL
+      IS_ERR(to)
                 || ...) {
   <+... when != goto l1;
-  -ENOMEM
+  PTR_ERR(to)
   ...+>
   }
-  if (copy_from_user(to, from, size) != 0) {
-    <+... when != goto l2;
-    -EFAULT
-    ...+>
-  }
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use ERR_CAST(x) rather than ERR_PTR(PTR_ERR(x)).  The former makes more
clear what is the purpose of the operation, which otherwise looks like a
no-op.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
type T;
T x;
identifier f;
@@

T f (...) { <+...
- ERR_PTR(PTR_ERR(x))
+ x
 ...+> }

@@
expression x;
@@

- ERR_PTR(PTR_ERR(x))
+ ERR_CAST(x)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a glue layer to support the sdhci driver on the ST SPEAr platform.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Cc: <shiraz.hashim@st.com>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

SDIO specification allows RAW (Read after Write) operation using
IO_RW_DIRECT command (CMD52) by setting the RAW bit.  This operation is
similar to ordinary read/write commands, except that both write and read
are performed using single command/response pair.  The Linux SDIO layer
already supports this internaly, only external function is missing for
drivers to make use, which is added by this patch.

This type of command is required to implement proper power save mode
support in wl1251 wifi driver.

Android has similar patch for G1 in it's tree for the same reason:

http://android.git.kernel.org/?p=kernel/common.git;a=commitdiff;h=74a47786f6ecbe6c1cf9fb15efe6a968451deb52Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kalle.valo@iki.fi>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core.  As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.

We might as well just delete the unused paramter.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: NSascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert PM operations to use dev_pm_ops.  This will facilitate the runtime
PM coversion which will add to dev_pm_ops hooks.

Note that dev_pm_ops version of the suspend hook no longer takes a 'state'
argument.  However, the MMC core function mmc_suspend_host() still takes a
'state' argument, but it is unused, so a dummy state variable was created
to pass to the MMC core.

In the future, the MMC core should be converted to drop this state
argument and the rest of the MMC drivers could be easily converted to
dev_pm_ops as well.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following changes were needed:
	- do not use in_interrupt() because it will not work
	with threaded interrupts

In addition, the following improvements were made:
	- ensure DMA is unmapped only after the final DMA interrupt
	- ensure a request is completed only after the final DMA interrupt
	- disable controller interrupts when a request is not in progress
	- remove the spin-lock protecting the start of a new request from
	an unexpected interrupt because the locking was complicated and
	a 'req_in_progress' flag suffices (since the spin-lock only defers
	the unexpected interrupts anyway)
	- instead use the spin-lock to protect the MMC interrupt handler
	from the DMA interrupt handler
	- remove the semaphore preventing DMA from being started while
	the previous DMA is still in progress - the other changes make that
	impossible, so it is now a BUG_ON condition
	- ensure the controller interrupt status is clear before exiting
	the interrrupt handler

In general, these changes make the code safer but do not fix any specific
bugs so backporting is not necessary.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Tested-by: NVenkatraman S <svenkatr@ti.com>
Acked-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Wifi over SDIO doesn't work correctly without multiblock, so enable this.
This patch depends on the following patches:
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable the ADMA feature in the 6410 SDHCI controller driver.
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The s3c6410 sdhci controller does not support the 'End' attribute and NOP
attribute in the same 8-Byte ADMA descriptor.  This patch adds a new quirk
to identify sdhci host contollers with such behaviour.  In addition to
this, for controllers using the new quirk, the last entry in the ADMA
descritor table is marked with the 'End' attribute (instead of using a NOP
descriptor with 'End' attribute).
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Unfortunately some architectures #define their read{b,w,l} and
write{b,w,l} I/O accessors which makes the SDHCI I/O accessor functions of
the same names subject to preprocessing.  This leads to the following
compiler error,

In file included from drivers/mmc/host/sdhci.c:26:
drivers/mmc/host/sdhci.h:318:35: error: macro "writel" passed 3 arguments, but takes just 2

Rename the SDHCI I/O functions so that CONFIG_MMC_SDHCI_IO_ACCESSORS can
be enabled for architectures that implement their read{b,w,l} and
write{b,w,l} functions with macros.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Cc: Zhangfei Gao <zgao6@marvell.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NBen Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NZhangfei Gao <zgao6@marvell.com>
Reviewed-by: NMatt Fleming <matt@console-pimps.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Atmel-mci support for SDIO interrupts.  This adds the enable_sdio_irq()
function and the configuration of sdio irq mask per slot.  With this irq
mask information, we keep the idea of multiple slot per sd/mmc host (not
only A and B).  MMC_CAP_SDIO_IRQ is added according to slot configuration.

A new little function is added to run mmc_signal_sdio_irq() during
interrupt handling routine.
Signed-off-by: NAnders Grahn <anders.grahn@hd-wireless.se>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

MMCIF is the MMC Host Interface in SuperH.
Signed-off-by: NYusuke Goda <yusuke.goda.sx@renesas.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable high speed support for atmel-mci driver.  This support is dependent
of the revision of the IP and, of course, the capacity of the SD card
used.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The clearing of mrq via a memset at the top of the for loop in
mmc_wait_for_app_cmd() is not required as mrq is not used and there is
another clearing of mrq just below.  We remove the first memset since if
the initial tests in the for loop fail the memset is not required.
Signed-off-by: NMark Asselstine <asselsm@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve the suspend and resume callbacks in DaVinci MMC host controller
driver.  Modify the reset status of the contorller and clock during
suspend and resume.  Also migrate the power management callbacks from
platform driver to dev_pm_ops structure.

Tested on DA850/OMAP-L138 EVM.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a helper function which will aid in changing the reset
status of the controller.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some hosts have an extended SDHCI iomem size, so the driver should
only print errors if the iomem size is less than 0x100.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NRichard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This includes platform ops, quirks and (de)initialization callbacks.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some hosts (e.g.  as found in CNS3xxx SOCs) report wrong value in
CLOCK_BASE capability field, and currently there is no way to force the
SDHCI core to use the platform-provided base clock value.

This patch implements CAP_CLOCK_BASE_BROKEN quirk.  When enabled, the
SDHCI core will always use base clock frequency provided by the platform.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The omap850 and omap730 use 16-bit registers instead of 32-bit, requiring
a modification of the register addresses in the mmc-omap driver.  To
resolve this, a bit shift is performed on base register addresses, either
by 1 or 2 bits depending on the CPU in use.  This yields the correct
registers for each CPU.
Signed-off-by: NMarek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Ben Dooks <ben@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On some platforms like DM355, the number of EDMA parameter slots available
for EDMA_SLOT_ANY usage are few.  In such cases, if MMC/SD uses 16 slots
for each instance of MMC controller, then the number of slots available
for other modules will be very few.

By passing the number of EDMA slots to be used in MMC driver from platform
data, EDMA slots available for other purposes can be controlled.

Most of the platforms will not use this platform data variable.  But on
DM355, as the number of EDMA resources available is limited, the number of
scatter- gather segments used inside the MMC driver can be 8 (passed as
platform data) instead of 16.  On DM355, when the number of scatter-gather
segments was reduced to 8, I saw a performance difference of about
0.25-0.4 Mbytes/sec during write.  Read performance variations were
negligible.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  agp: amd64, fix pci reference leaks
  drm/edid: Allow non-fatal checksum errors in CEA blocks
  drm/radeon/kms: suppress a build warning (unused variable)
  drm: Fixes linux-next & linux-2.6 checkstack warnings:
  nouveau: fix acpi_lid_open undefined
  drm/radeon/kms: release AGP bridge at suspend