Data sheet at:
http://www.sensirion.ch/en/pdf/product_information/Datasheet-humidity-sensor-SHT1x.pdf

These sensors communicate over a 2 wire bus running a device specific
protocol.  The complexity of the driver is mainly due to handling the
substantial delays between requesting a reading and the device pulling the
data line low to indicate that the data is available.  This is handled by
an interrupt that is disabled under all other conditions.

I wasn't terribly clear on the best way to handle this, so comments on
that aspect would be particularly welcome!

Interpretation of the temperature depends on knowing the supply voltage.
If configured in a board config as a regulator consumer this is obtained
from the regulator subsystem.  If not it should be provided in the
platform data.

I've placed this driver in the hwmon subsystem as it is definitely a
device that may be used for hardware monitoring and with it's relatively
slow response times (up to 120 millisecs to get a reading) a caching
strategy certainly seems to make sense!
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This controller can be found on the D-Link DNS-323 for instance, where
it is to be configured via static i2c_board_info in the board-specific
mach-orion/dns323-setup.c; this driver supports only the new-style
driver model.
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NHerbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: NMatthew Palmer <mpalmer@debian.org>
Signed-off-by: NLaurie Bradshaw <bradshaw.laurie@googlemail.com>
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.

There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).

Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Make use of the new abstraction layer and add a new transport layer for
spi.  Works fine on a PXA based board.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NEric Piel <eric.piel@tremplin-utc.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.

I have tested the driver with my board, and it appears to work fine.  With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power.  With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power.  I'm not drawing any current at the
moment, so this is reasonable.  The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.

I didn't attempt to support changing any of the chip's settings or
enabling the FET.  I'm not sure even how to do that and still fit within
the hwmon framework.  :)
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip
Signed-off-by: NDavide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.

If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>

Hwmon driver for the ADT7475 chip.
Signed-off-by: NJordan Crouse <jordan.crouse@amd.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The sensor can be accessed via various buses.  In particular, SPI, I²C
and, on HP laptops, via a specific ACPI API (the only one currently
supported).  Separate this latest platform from the core of the sensor
driver to allow support for the other bus type.  The second, and more
direct goal is actually to be able to merge this part with the
hp-disk-leds driver, which has the same ACPI PNP number.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

New driver to play with.  As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors.  This driver has been tested on an IntelliStation Z30.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard").  It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.

This driver was first written by Yan Burman.  Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now).  Pavel Machek removed few more features and switched locking from
semaphore to mutex.

Several people have contributed to the database of the axes.

[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NYan Burman <burman.yan@gmail.com>
Signed-off-by: NPavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NEric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.

Now changed to generic HWMON device and expose all the ADC input value
through sysfs.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is a PIC16F747 based controller that monitors and consolidates
the hardware access to various fan and temperature values reported by
adr7462 and similar devices behind an I2C bus.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SPI driver for analog to digital converters national semiconductor
ADC081S101, ADC124S501, ...

Code for 8 channels by Tobias Himmer.

This driver adds support for National Semiconductor ADC<bb><c>S<sss> chip
family, where:

 * bb  is the resolution in number of bits (8, 10, 12)
 * c   is the number of channels (1, 2, 4, 8)
 * sss is the maximum conversion speed (021 for 200 kSPS, 051 for 500
   kSPS and 101 for 1 MSPS)

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Cc: Tobias Himmer <tobias@himmer-online.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Driver for the Analog Devices AD7414 temperature monitoring chip.
Signed-off-by: NSean MacLennan <smaclennan@pikatech.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This driver reads IBM Active Energy Manager energy/temperature/power
sensors on IBM System X hardware.

[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Signed-off-by: NSteve Hardy <steve@linuxrealtime.co.uk>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Signed-off-by: NKevin Lo <kevlo@kevlo.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

New driver to read FB-DIMM temperature sensors on systems with the
Intel 5000 series chipsets.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds a new merged driver for FSC sensor chips, it merges the fscher
and fscpos drivers and adds support for the FSC Scylla, Heracles and Heimdall
chips.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Add a driver to export IBM PowerExecutive power meter sensors.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Add support for Fintek F75375S/SP and F75373.
Signed-off-by: NRiku Voipio <riku.voipio@movial.fi>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

New driver to expose temperature and fan controls attached to Analog
Devices ADT7470 hwmon chips.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This is the second version of a new driver for the hardware monitoring features
of the Fintek F71882FG and F71883FG Super-I/O chips. This version has several
small fixes for flaws discovered during the review of the first version.

This version of the driver does not support the pwm part of these chips (yet).
I'll first design a sysfs api for this and post that for discussion, and then
implement pwm support as an incremental patch over this one.

This driver supports all sensors of this chip, except for the vid inputs. The
vid inputs are somewhat documented in the datasheet, but I know nothing about
vid/vrm stuff. Help with this would be much appreciated.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds support for THMC50 and ADM1022 hardware monitoring chips.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds support for the LM93 hardware monitoring chip.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

This patch adds a new driver for the hardware monitoring features of the
third revision of the Abit uGuru chip, found on recent Abit
motherboards. This is an entirely different beast then the first and
second revision (its again a winbond microcontroller, but the "protocol"
to talk to it and the bank addresses are very different.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>

Add support for the hardware monitoring and fan control
capabilities of the SMSC DME1737 and Asus A8000 Super-I/O chips.

The hardware monitoring logic of this chip is similar to the LM85 but
has some additional features that this driver supports. Even though
it's a Super-I/O chip, the hardware monitoring logic can only be
accessed via SMBus.

Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This driver provides support for the Apple System Management Controller, which
provides an accelerometer (Apple Sudden Motion Sensor), light sensors,
temperature sensors, keyboard backlight control and fan control. Only
Intel-based Apple's computers are supported (MacBook Pro, MacBook, MacMini).

[bunk@stusta.de: make drivers/hwmon/applesmc.c:backlight_work stati]
[khali@linux-fr.org: fix temperature attribute file names]
Signed-off-by: NNicolas Boichat <nicolas@boichat.ch>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A driver for the Analog Devices AD7416, AD7417 and AD7418 chips.
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add the support for the digital temperature sensor found in recent
Intel Core CPUs.
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This driver supports the Maxim MAX6650 and MAX6651 fan speed
monitoring and control chips.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NCorentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This driver adds support for the Apple Motion Sensor (AMS) as found in 2005
revisions of Apple PowerBooks and iBooks.  It implements both the PMU and
I2C variants.  The I2C driver and mouse emulation is based on code by
Stelian Pop, while the PMU driver has been developped by Michael Hanselmann.
HD parking support will be added later.

Various people contributed fixes to this driver, including
Aristeu Sergio Rozanski Filho and Jean Delvare.
Signed-off-by: NStelian Pop <stelian@popies.net>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NRobert Love <rml@novell.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add support for the W83793 hardware monitoring chip. This driver
was originally contributed by Yuan Mu of Winbond Electronics Corp.
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This is a new hardware monitoring driver for the National Semiconductor
PC87427 Super-I/O chip. It only supports fan speed monitoring for now,
while the chip can do much more.

Thanks to Amir Habibi at Candelis for setting up a test system, and to
Michael Kress for testing several iterations of this driver.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

hwmon: New driver for the VIA VT1211

This is a new driver for the VIA VT1211 Super-IO chip. It is a rewrite
of the existing vt1211 driver (by Mark D. Studebaker and Lars Ekman)
which has been around for a while but never made it into the main
kernel tree.

It is implemented as a platform driver and therefore requires
lm_sensors 2.10.1 to function properly.
Signed-off-by: NJuerg Haefliger <juergh@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for the temperature sensor(s) found in AMD K8 CPUs.
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>