These are compatible with standard ALC269 parser.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In case there is one "Headphone Jack" and one "Dock Headphone Jack",
one of them will get an index, even though that is not needed.
This patch fixes that issue.

BugLink: https://bugs.launchpad.net/bugs/1060729Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

After the recent patch "ALSA: hda - use both input paths on Conexant
auto parser" suddenly we can have more than one "Mic Boost", this
happened on Acer Aspire One 722. Therefore we must add the possibility
to put an index on this "Mic Boost" just as we do for the other
"Mic Boost" earlier in the same function.

BugLink: https://bugs.launchpad.net/bugs/1059523Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the loopback timer handler is running, calling del_timer() (for STOP
trigger) will not wait for the handler to complete before deactivating the
timer. The timer gets rescheduled in the handler as usual. Then a subsequent
START trigger will try to start the timer using add_timer() with a timer pending
leading to a kernel panic.

Serialize the calls to add_timer() and del_timer() using a spin lock to avoid
this.
Signed-off-by: NOmair Mohammed Abdullah <omair.m.abdullah@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

There was a race condition when the system suspends while hda_power_work
is running in the work queue.  If system suspend (snd_hda_suspend)
happens after the work queue releases power_lock but before it calls
hda_call_codec_suspend,  codec_suspend runs with power_on=0, causing the
codec to power up for register reads, and hanging when it calls
cancel_delayed_work_sync from the running work queue.

The call chain from the work queue will look like this:
hda_power_work <<- power_on = 1, unlock, then power_on cleard by suspend
  hda_call_codec_suspend
    hda_set_power_state
      snd_hda_codec_read
        codec_exec_verb
          snd_hda_power_up
	    snd_hda_power_save
	      __snd_hda_power_up
	        cancel_delayed_work_sync <<-- cancelling executing wq

Fix this by waiting for the work queue to finish before starting suspend
if suspend is not happening on the work queue.
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p

@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
        cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In commit af741c15 ("ALSA: hda/realtek - Call alc_auto_parse_customize_define()
always after fixup"), alc_auto_parse_customize_define was moved after
detection of ALC271X.

The problem is that detection of ALC271X relies on spec->cdefine.platform_type,
and it's set on alc_auto_parse_customize_define.

Move the alc_auto_parse_customize_define and its required fixup setup
before the block doing the ALC271X and other codec setup.

BugLink: https://bugs.launchpad.net/bugs/1006690Signed-off-by: NHerton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Reviewed-by: NDavid Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The Lenovo IdeaPad U310 has an internal mic where the right channel
is phase inverted.
Signed-off-by: NFelix Kaechele <felix@fetzig.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

For less duplication of code between codecs, and to make it easier
in the future to improve code for all codecs simultaneously.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Moving towards less duplication of code between codecs - this patch
takes some of the common code of unsol event handling and makes it
generic.
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds support for Dialog semiconductor's DA9055 audio codec.

This has been tested on DA9055 EVB with Samsung SMDK6410 board.
Signed-off-by: NAshish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: NDavid Dajun Chen <david.chen@diasemi.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert eukrea-tlv320 to platform driver.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Apart from pure matching, the bindings also support setting the the
reset gpio line.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In some circumstances we may need to flush volume updates to the device
after switching to class W mode. Do this unconditionally to ensure that
these situations are handled.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The volume update bits were being set on all but one input and one output.
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The third output on WM5110 is a general purpose headphone output which can
be used to drive an earpice rather than a dedicated earpiece driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some devices support additional clock rates.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The interrupt handler uses the chip state.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We will fail to probe without one.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We never set the GPIO from atomic context so there's no reason why we
can't support a GPIO that needs to sleep when configuring.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allow regulators managed via DAPM to make use of the bypass support that
has recently been added to the regulator API by setting a flag
SND_SOC_DAPM_REGULATOR_BYPASS. When this flag is set the regulator will
be put into bypass mode before being disabled, allowing the regulator to
fall into bypass mode if it can't be disabled due to other users.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

According to cs4270 datasheet, there is no reference to mono mode.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

With this parameter added to dmaengine_prep_dma_cyclic() the API will be in
sync with other dmaengine_prep_*() functions.
The dmaengine_prep_dma_cyclic() function primarily used by audio for cyclic
transfer required by ALSA, we use the from audio to ask dma drivers to
suppress interrupts (if DMA_PREP_INTERRUPT is cleared) when it is supported
on the platform.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
CC: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Passing struct snd_dma_buffer pointer instead, so that they work no
matter whether real SG buffer is used or not.

This is a preliminary work for the HD-audio DSP loader code.
Signed-off-by: NIan Minett <ian_minett@creativelabs.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When the kernel has been booted with DT blob the platform data is NULL for
the driver.
We need to construct the pdata based on the DT information for runtime use.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Access the pdata via a pointer within the twl4030_priv structure.
In preparation for DeviceTree support.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Allocate the private data with devm_kzalloc.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We no longer have users for the set_hs_extmute callback which has been
replaced by hs_extmute_gpio so the codec driver can handle the external
mute if it is needed by the board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Remove the use of set_hs_extmute callback and let the codec driver to
handle the extmute GPIO.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The external mute (if it is in use) is handled by a GPIO line. Prepare to
remove the set_hs_extmute callback and replace it with:
hs_extmute_gpio: the GPIO number to use for external mute

When the users of set_hs_extmute has been converted the callback can be removed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Original author: Russell King <rmk+kernel@arm.linux.org.uk>

Switch the omap-pcm to use dmaengine.
Certain features are not supported by after dmaengine conversion:
1. No period wakeup mode
   DMA engine has no way to communicate this information through
   standard channels.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Set the dma_data for the stream (snd_soc_dai_set_dma_data) at dai_startup
time so omap-pcm will have access to the needed information regarding to
the DMA channel earlier.
This is needed for the clean dmaengine support.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Instead of the OMAP DMA data type definition the data_type will be used to
specify the number of bits the DMA word should be configured or 0 in case
when based on the stream's format the omap-pcm can decide the needed DMA
word size.
This feature is needed for the omap-hdmi where the sDMA need to be
configured for 32bit word type regardless of the audio format used.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>