Ensure that the rx tasklet is no longer running when entering the reset path.
Also remove the distinction between flush and no-flush frame processing.
If a frame has been received and ACKed by the hardware, the stack needs to see
it, so that the BA receive window does not go out of sync.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During teardown, mac80211 will not return a new beacon. This is normal and
handled properly in the driver, so there's no need to spam the user with a kernel
warning here.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.

Cc: <stable@vger.kernel.org>
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BAND_G is implicit when BAND_GN is present.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently "adapter->config_bands" is updated during infra
association only if channel is provided by user in "iw connect"
command. config_bands is used while preparing association
request to calculate supported rates by intersecting our rates
with the rates advertised by AP.

There is corner case in which we include zero rates in
supported rates TLV based on previous IBSS network history,
which leads to association failure.

This patch fixes the problem by correctly updating config_bands.

Cc: "3.7.y" <stable@vger.kernel.org>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent versions of udev cause synchronous firmware loading from the
probe routine to fail because the request to user space would time
out. The original fix for b43 (commit 6b6fa586) moved the firmware
load from the probe routine to a work queue, but it still used synchronous
firmware loading. This method is OK when b43 is built as a module;
however, it fails when the driver is compiled into the kernel.

This version changes the code to load the initial firmware file
using request_firmware_nowait(). A completion event is used to
hold the work queue until that file is available. This driver
reads several firmware files - the remainder can be read synchronously.
On some test systems, the async read fails; however, a following synch
read works, thus the async failure falls through to the sync try.

Reported-and-Tested by: Felix Janda <felix.janda@posteo.de>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>  (V3.4+)
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  The fields must be null-terminated, or simple_strtoul will cause issue.
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not dereference p->station_id after kfree(cmd) because p
points into the cmd data structure.
Signed-off-by: NNickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJulian Wollrath <jwollrath@web.de>
Acked-by: NLarry Finger <Larry.finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds support for the 60 GHz 802.11ad Wilocity card
through a new driver, wil6210. Wilocity implemented the
firmware, QCA maintains the device driver.

Currently supported:

- STA: with security
- AP: limited to 1 connected STA, security disabled
- Monitor: due to a hardware/firmware limitation
  either control or non-control frames are monitored

Using a STA and AP with this drive, one can assemble
a fully functional BSS. Throughput of 1.2Gbps is achieved
with iperf.

The wil6210 cards have on-board flash memory for the
firmware, the cards comes pre-flashed and no firmware
download is required.

For more details see:

http://wireless.kernel.org/en/users/Drivers/wil6210Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 683b6d3b... "cfg80211: pass a channel definition struct"
accidentally changed "==" to "!=".
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wait_event_interruptible function returns -ERESTARTSYS if it's
interrupted by a signal. Driver should check the return value
and handle this case properly.

In mwifiex_wait_queue_complete() routine, as we are now checking
wait_event_interruptible return value, the condition check is not
required. Also, we have removed mwifiex_cancel_pending_ioctl()
call to avoid a chance of sending second command to FW by other path
as soon as we clear current command node. FW can not handle two
commands simultaneously.

Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ath9k consists of 2 different sub-modules: ATH9K and ATH9K_HTC.
Both uses common Atheros code from ath.ko and need ATH_COMMON.

However, while ATH9K selects ATH_COMMON, ATH9K_HTC does not.
As result, if ATH9K_HTC is the only Atheros card selected, compilation fails with
unresolved symbols.

This patch moves ATH_COMMON selection to the common part for both
ATH9K and ATH9K_HTC
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's a bug in the currently released firmware version,
the sequence control in the Tx response isn't updated in
all cases. Take it from the packet as a workaround.

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

By accident, commit eb647644
("iwlwifi: protect use_ict with irq_lock") changed the return
value of the iwl_pcie_isr() function in case it handles an
interrupt -- it now returns IRQ_NONE instead of IRQ_HANDLED.

Put back the correct return value.

Cc: stable@vger.kernel.org
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

RSN IEs got incorrectly parsed and therefore ap mode using WPA2
security was not working.

Cc: stable@vger.kernel.org
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patches from Canonical involved the introduction of new source
files debug.[ch]. That coincided with other patches from Broadcom
introducing the same files.

Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kernel 3.8 implements checking of all DMA mapping calls and issues
a WARNING for the first it finds that is not checked.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds USBIDs for:
	- DrayTek Vigor 530
	- Zoom 4410a

It also adds a note about Gemtek WUBI-100GW
and SparkLAN WL-682 USBID conflict [WUBI-100GW
is a ISL3886+NET2280 (LM86 firmare) solution,
whereas WL-682 is a ISL3887 (LM87 firmware)]
device.

Source: <http://www.wikidevi.com/wiki/Intersil/p54/usb/windows>

Cc: <stable@vger.kernel.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We fail to release 'urb' if '_rtl_prep_rx_urb()' fails in
_rtl_usb_receive().
This patch should take care of the leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Populate iniModesRxGain with the correct initvals
array for AR9485 v1.1

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wlc_lcnphy_rx_iq_cal_gain is called during initialization, i. e. when
executing brcms_up.
But brcms_up is called from brcms_ops_start while the latter holds a spin lock.
Thus, we cannot use usleep_range but have to use udelay.

This fixes:
BUG: scheduling while atomic: NetworkManager/1652/0x00000200
[...]
Call Trace:
 [<ffffffff81582522>] __schedule_bug+0x48/0x54
 [<ffffffff815892b6>] __schedule+0x596/0x6d0
 [<ffffffff81589719>] schedule+0x29/0x70
 [<ffffffff8158893c>] schedule_hrtimeout_range_clock+0xfc/0x140
 [<ffffffff81060f10>] ? update_rmtp+0x70/0x70
 [<ffffffff81588993>] schedule_hrtimeout_range+0x13/0x20
 [<ffffffff810495e0>] usleep_range+0x40/0x50
 [<ffffffffa05dedcb>] wlc_lcnphy_rx_iq_cal.constprop.10+0x59b/0xa90 [brcmsmac]
 [<ffffffffa05df4ce>] wlc_lcnphy_periodic_cal+0x20e/0x220 [brcmsmac]
 [<ffffffffa05dce8d>] ? wlc_lcnphy_set_tx_pwr_ctrl+0x21d/0x3c0 [brcmsmac]
 [<ffffffffa05e0cfc>] wlc_phy_init_lcnphy+0xacc/0x1100 [brcmsmac]
 [<ffffffffa05e0230>] ? wlc_phy_txpower_recalc_target_lcnphy+0x90/0x90 [brcmsmac]
 [<ffffffffa05d7c7d>] wlc_phy_init+0xcd/0x170 [brcmsmac]
 [<ffffffffa05c9dfe>] brcms_b_bsinit.isra.65+0x12e/0x310 [brcmsmac]
 [<ffffffffa05d061b>] brcms_c_init+0x8fb/0x1170 [brcmsmac]
 [<ffffffffa05c3a0a>] brcms_init+0x5a/0x70 [brcmsmac]
 [<ffffffffa05ce76c>] brcms_c_up+0x1ac/0x4a0 [brcmsmac]
 [<ffffffffa05c3c65>] brcms_up+0x25/0x30 [brcmsmac]
 [<ffffffffa05c44c0>] brcms_ops_start+0xd0/0x100 [brcmsmac]
[...]
Signed-off-by: NNiels Ole Salscheider <niels_ole@salscheider-online.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added USB ID for T-Com Sinus 154 data II.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTomasz Guszkowski <tsg@o2.pl>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sean reported that as of 3.7, his AR9170 device no longer works
because the driver fails during initialization. He noted this
is due to:
"In carl9170/fw.c, ar->hw->wiphy is tagged with
NL80211_IFTYPE_MESH_POINT support if the firmware has Content
after Beacon Queuing. This is both in interface_modes and the
only iface_combinations entry.

If CONFIG_MAC80211_MESH is not set, ieee80211_register_hw
removes NL80211_IFTYPE_MESH_POINT from interface_modes, but
not iface_combinations.

wiphy_register then checks to see if every interface type in
every interface combination is in interface_modes.
NL80211_IFTYPE_MESH_POINT was removed, so you get a WARN_ON
warning and it returns -EINVAL, giving up."

Unfortunately, the iface_combination (types) feature bitmap
in ieee80211_iface_limit is part of a const member in the
ieee80211_iface_combination struct. Hence, the MESH_POINT
feature flag can't be masked by wiphy_register in the
same way as interface_modes in ieee80211_register_hw.

Cc: <stable@vger.kernel.org>
Reported-by: NSean Patrick Santos <quantheory@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Tested-by: NSean Patrick Santos <quantheory@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Incorrect use of usb_alloc_coherent memory as input buffer to usb_control_msg
can cause problems in arch DMA code, for example kernel BUG at
'arch/arm/include/asm/dma-mapping.h:321' on ARM (linux-3.4).

Change _usb_writeN_sync use kmalloc'd buffer instead.

Cc: stable@vger.kernel.org
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since ath9k makes use of mac80211's debugfs hooks to
maintain station statistics, make ATH9K_DEBUGFS
select MAC80211_DEBUGFS. This fixes the issue reported by
Fengguang Wu:

drivers/net/wireless/ath/ath9k/debug.c: In function 'ath9k_sta_add_debugfs':
drivers/net/wireless/ath/ath9k/debug.c:1589:4: error: 'struct ath_node' has no member named 'node_stat'
drivers/net/wireless/ath/ath9k/debug.c: In function 'ath9k_sta_remove_debugfs':
drivers/net/wireless/ath/ath9k/debug.c:1599:19: error: 'struct ath_node' has no member named 'node_stat'
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In commit 9c0ece06 ("Get rid of Documentation/feature-removal.txt"),
Linus removed feature-removal-schedule.txt from Documentation, but there
is still some reference to this file.  So remove them.
Signed-off-by: NTao Ma <boyu.mt@taobao.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bug introduced in commit:
wireless: allow Atheros card to not depend on ath.ko

Commit in question changed CONFIG_ATH_COMMON to CONFIG_ATH_CARDS as
"Atheros card" indication in drivers/net/wireless/ath/Kconfig but it
is used also by drivers/net/wireless/Makefile

If there are only Atheros cards that do not require ATH_COMMON, whole
Makefile for Atheros cards was not executed; and as result, driver
won't compile in this case.

Change in CONFIG_ option name should be reflected in the
drivers/net/wireless/Makefile
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Tested-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In commit 'mac80211: support radiotap vendor namespace RX data'
new fields were added to 'struct ieee80211_rx_status' and those
fileds must be zeroed. However the rt2x00 driver stores driver
specific data in the cb array of the rx skbs, so the fields
might contain garbage and this can cause unexpected behaviour.

The rt2x00 driver from the compat-wireless-2012-12-01
tarball caused the following warning:

  WARNING: at
  /devel/ramips/build_dir/target-mipsel_r2_uClibc-0.9.33.2/linux-ramips_rt305x/
  compat-wireless-2012-12-01/net/mac80211/rx.c:115 ieee80211_rx_irqsafe+0x274/0xbcc
  [mac80211]()
  Modules linked in: dwc_otg ledtrig_usbdev nf_nat_irc
  nf_nat_ftp nf_conntrack_irc nf_conntrack_ftp ipt_MASQUERADE
  iptable_nat nf_nat pppoe xt_conntrack xt_CT xt_NOTRACK iptable_raw
  xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack pppox
  ipt_REJECT xt_TCPMSS xt_comment xt_multiport xt_mac xt_limit
  iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async
  ppp_generic slhc rt2800pci(O) rt2800lib(O) rt2x00soc(O) rt2x00pci(O)
  rt2x00lib(O) mac80211(O) usbcore usb_common nls_base crc_itu_t
  crc_ccitt eeprom_93cx6 cfg80211(O) compat(O) arc4 aes_generic
  crypto_blkcipher cryptomgr aead crypto_hash crypto_algapi leds_gpio
  button_hotplug(O) gpio_keys_polled input_polldev input_core
  Call Trace:
  [<801e96b4>] dump_stack+0x8/0x34
  [<80010a9c>] warn_slowpath_common+0x78/0xa4
  [<80010ae0>] warn_slowpath_null+0x18/0x24
  [<80a9710c>] ieee80211_rx_irqsafe+0x274/0xbcc [mac80211]

The patch ensures that each field gets initialized with
zeroes.

Cc: <users@rt2x00.serialmonkey.com>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due to my recent commit (ath9k: allow to load EEPROM
content via firmware API) smatch complains about that
the 'pdata' variable in 'ath9k_hw_init' can be NULL
and it is dereferenced before checking that. That is
absolutely correct.

Check the 'pdata' variable before using it to avoid
a NULL pointer dereference.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is true for at least AR5213, and shouldn't be different for other
ath5k PHYs. Tested on AR2413 and AR5414.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Tested-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accurate RX timestamp reporting is important for proper IBSS merging,
mesh synchronization, and MCCA scheduling. Namely, knowing where the TSF
is recorded is needed to sync with the beacon timestamp field.

Tested with AR9271.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accurate RX timestamp reporting is important for proper IBSS merging,
mesh synchronization, and MCCA scheduling. Namely, knowing where the TSF
is recorded is needed to sync with the beacon timestamp field.

Tested with AR9280.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Someone who physically disassembled the device confirms that its
chipset is Ralink RT5370n.

(Fixed-up after having already merged original patch. -- JWL)
Signed-off-by: NMaia Kozheva <sikon@ubuntu.com>
Reviewed-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>