Some irq_chips need to know the state of wakeup mode for
setting the trigger type etc. Reflect it in irq_data state.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

irq_chips, which require to mask the chip before changing the trigger
type should set this flag. So the core takes care of it and the
requirement for looking into desc->status in the chip goes away.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>

Looking through irq_chip implementations I noticed that some of them
have special requirements, like setting the type masked and therefor
fiddle in irq_desc->status. Add a flag field, so the core code can
handle it.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Put the constants into an enum and document them.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

That's the data structure chip functions get provided. Also allow them
to signal the core code that they updated the flags in irq_data.state
by returning IRQ_SET_MASK_OK_NOCOPY. The default is unchanged.

The type bits should be accessed via:

val = irqd_get_trigger_type(irqdata);
and
irqd_set_trigger_type(irqdata, val);

Coders who access them directly will be tracked down and slapped with
stinking trouts.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Keep status in sync until last abuser is gone.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

That's the right data structure to look at for arch code.

Accessor functions are provided.

	 irqd_is_per_cpu(irqdata);
	 irqd_can_balance(irqdata);

Coders who access them directly will be tracked down and slapped with
stinking trouts.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Its' too ugly and needs to go. The only users are core code and
parisc. Core code does not need it and parisc gets a new check once
IRQ_PER_CPU is reflected in irq_data.state.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The saving of this switch is minimal versus the ifdef mess it
creates. Simple enable PER_CPU unconditionally and remove the config
switch.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

chip implementations need to know about it. Keep status in sync until
all users are fixed. 

Accessor function: irqd_is_setaffinity_pending(irqdata)

Coders who access them directly will be tracked down and slapped with
stinking trouts.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Some chip implementations need to access certain status flags. With
sparse irqs that requires a lookup of the irq descriptor. Add a state
field which contains such flags.

Name it in a way which will make coders happy to access it with the
proper accessor functions. And it's easy to grep for.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

No users outside of core.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Keep status in sync until all users are fixed.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Keep status in sync until all users are fixed.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Keep status in sync until all abusers are fixed.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

No users outside of core.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

No users outside of core.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

We need to maintain the flag for now in both fields status and istate.
Add a CONFIG_GENERIC_HARDIRQS_NO_COMPAT switch to allow testing w/o
the status one. Wrap the access to status IRQ_INPROGRESS in a inline
which can be turned of with CONFIG_GENERIC_HARDIRQS_NO_COMPAT along
with the define.

There is no reason that anything outside of core looks at this. That
needs some modifications, but we'll get there.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

No users outside of core.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

No need for a separate function in the core code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

No users outside.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

No users outside of core
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

With the chip.end() function gone we might run into a situation where
a poll call runs and the real interrupt comes in, sees IRQ_INPROGRESS
and disables the line. That might be a perfect working one, which will
then be masked forever.

So mark them polled while the poll runs. When the real handler sees
IRQ_INPROGRESS it checks the poll flag and waits for the polling to
complete. Add the necessary amount of sanity checks to it to avoid
deadlocks.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

While rumaging through arch code I found that there are a few
workarounds which deal with the fact that the initial affinity setting
from request_irq() copies the mask into irq_data->affinity before the
chip code is called. In the normal path we unconditionally copy the
mask when the chip code returns 0.

Copy after the code is called and add a return code
IRQ_SET_MASK_OK_NOCOPY for the chip functions, which prevents the
copy. That way we see the real mask when the chip function decided to
truncate it further as some arches do. IRQ_SET_MASK_OK is 0, which is
the current behaviour.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The irq namespace has become quite convoluted. My bad.  Clean it up
and deprecate the old functions. All new functions follow the scheme:

irq number based:
    irq_set/get/xxx/_xxx(unsigned int irq, ...)

irq_data based:
	 irq_data_set/get/xxx/_xxx(struct irq_data *d, ....)

irq_desc based:
	 irq_desc_get_xxx(struct irq_desc *desc)
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The mask which filters out the valid bits which can be set via
irq_modify_status() is missing IRQ_NO_BALANCING, which breaks UV.

Add IRQ_PER_CPU as well to avoid another one line patch for 39.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

For cases that wish to reserve a single IRQ at a given place simply
provide a wrapper in to the ranged reservation routine.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
LKML-Reference: <20101026071912.GD4733@linux-sh.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Use the cleanup functions of the dynamic allocator. No need to have
separate implementations.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

irq_2_iommu is now in the x86 code where it belongs. Remove all
leftovers.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>

sparse irq sets up NR_IRQS_LEGACY irq descriptors and archs then go
ahead and allocate more.

Use the unused return value of arch_probe_nr_irqs() to let the
architecture return the number of early allocations. Fix up all users.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

Mark a range of interrupts as allocated. In the SPARSE_IRQ=n case we
need this to update the bitmap for the legacy irqs so the enumerator
via irq_get_next_irq() works.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The current sparse_irq allocator has several short comings due to
failures in the design or the lack of it:

 - Requires iteration over the number of active irqs to find a free slot
   (Some architectures have grown their own workarounds for this)
 - Removal of entries is not possible
 - Racy between create_irq_nr and destroy_irq (plugged by horrible
   callbacks)
 - Migration of active irq descriptors is not possible
 - No bulk allocation of irq ranges
 - Sprinkeled irq_desc references all over the place outside of kernel/irq/
   (The previous chip functions series is addressing this issue)

Implement a sane allocator which fixes the above short comings (though
migration of active descriptors needs a full tree wide cleanup of the
direct and mostly unlocked access to irq_desc).

The new allocator still uses a radix_tree, but uses a bitmap for
keeping track of allocated irq numbers. That allows:

 - Fast lookup of a free slot
 - Allows the removal of descriptors
 - Prevents the create/destroy race
 - Bulk allocation of consecutive irq ranges
 - Basic design is ready for migration of life descriptors after
   further cleanups

The bitmap is also used in the SPARSE_IRQ=n case for lookup and
raceless (de)allocation of irq numbers. So it removes the requirement
for looping through the descriptor array to find slots.

Right now it uses sparse_irq_lock to protect the bitmap and the radix
tree, but after cleaning up all users we should be able convert that
to a mutex and to switch the radix_tree and decriptor allocations to
GFP_KERNEL.

[ Folded in a bugfix from Yinghai Lu ]
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

Arch code sets it's own irq_desc.status flags right after boot and for
dynamically allocated interrupts. That might involve iterating over a
huge array.

Allow ARCH_IRQ_INIT_FLAGS to set separate flags aside of IRQ_DISABLED
which is the default.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

Get the data structure from the core and provide inline wrappers to
access the irq_data members.

Provide accessor inlines for irq_data as well.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

Provide a irq_desc.status modifier function to cleanup the direct
access to irq_desc in arch and driver code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

move_irq() has no users. Remove it and simplify the ifdef forrest while at it.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

Move irq_desc and internal functions out of irq.h
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

This option covers now the old chip functions and the irq_desc data
fields which are moving to struct irq_data. More stuff will follow.

Pretty handy for testing a conversion, whether something broke or not.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

The low level irq chip functions want access to irq_desc->irq_data.
Provide new functions which hand down irq_data instead of the irq
number so these functions avoid to call irq_to_desc() which is a radix
tree lookup in case of sparse irq.

This provides all the old functions except one: end(). end() is a
relict of __do_IRQ() and will just go away with the __do_IRQ() code.

The replacement for set_affinity() has an extra argument "bool
force". The reason for this is to notify the low level code, that the
move has to be done right away and cannot be delayed until the next
interrupt happens. That's necessary to handle the irq fixup on cpu
unplug in the generic code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20100927121841.742126604@linutronix.de>
Reviewed-by: NH. Peter Anvin <hpa@zytor.com>
Reviewed-by: NIngo Molnar <mingo@elte.hu>

Convert all references in the core code to orq, chip, handler_data,
chip_data, msi_desc, affinity to irq_data.*
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@elte.hu>