DEFINE_STATIC_SRCU() defines srcu struct and do init at build time.
Signed-off-by: NLai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch generalizes VXLAN forwarding table entries allowing an administrator
to:
	1) specify multiple destinations for a given MAC
	2) specify alternate vni's in the VXLAN header
	3) specify alternate destination UDP ports
	4) use multicast MAC addresses as fdb lookup keys
	5) specify multicast destinations
	6) specify the outgoing interface for forwarded packets

The combination allows configuration of more complex topologies using VXLAN
encapsulation.

Changes since v1: rebase to 3.9.0-rc2
Signed-Off-By: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

caif_shm is an old implementation
caif_shm will be replaced by caif_virtio

[ As explained by Linus Walleij: "U5500 used this, but was cancelled
  and the silicon did not reach anyone outside ST-Ericsson.  Then for
  the next platforms, we have gone for the leaner & cleaner approach
  of using virtio, rpmesg and rproc." ]
Signed-off-by: NErwan Yvin <erwan.yvin@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NSjur Brendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace ip_fast_csum with csum_replace2 to save cpu cycles
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

replace ip_fast_csum with csum_replace2 to save cpu cycles
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default value is 128, not 256
	#grep gc_thresh1 net/ -rI
	net/decnet/dn_neigh.c:	.gc_thresh1 =			128,
	net/ipv6/ndisc.c:	.gc_thresh1 =	 128,
	net/ipv4/arp.c:	.gc_thresh1	= 128,
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.

Remove the unnecessary additional error logging.

Around these deletions:

o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed as the earlier method of manipulating this register via PCI
Config space is disallowed by certain Hypervisors.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the NIC PCI function may be used by other protocols, the chip interrupts
must be enabled in be_probe() itself rather than be_open().
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

COMPAT_NET_DEV_OPS was removed a while back and with it the definition of
netdev_resync_ops() went away. Let's finish the clean-up.
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The resource ID used for VM socket control packets (0) is already
used for the VMCI_GET_CONTEXT_ID hypercall so a new ID (15) must be
used when the guest sends these datagrams to the hypervisor.

The hypervisor context ID must also be removed from the internal
blacklist.
Signed-off-by: NReilly Grant <grantr@vmware.com>
Acked-by: NAndy King <acking@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows LRO aggregation on bonded devices that contain an
NX3031 device. It also adds a for_each_netdev_in_bond_rcu(bond, slave)
macro which executes for each slave that has bond as master.

V3: After testing and discussing this with Rajesh, I decided to keep the
    vlan ip cache and just rename it to ip_cache since it will store bond
    ip addresses too. A new master flag has been added to the ip cache to
    denote that the address has been added because of a master device.
    I've taken care of the enslave/release cases by checking for various
    combinations of events and flags (e.g. netxen has a master, it's a
    bond master and it's not marked as a slave means it is being enslaved
    and is dev_open()ed in bond_enslave).
    I've changed netxen_free_ip_list() to have a "master" parameter which
    causes all IP addresses marked as master to be deleted (used when a
    netxen is being released). I've made the patch use the new upper
    device API as well. The following cases were tested:
    - bond -> netxen
    - vlan -> netxen
    - vlan -> bond -> netxen

V2: Remove local ip caching, retrieve addresses dynamically and
    restore them if necessary.

Note: Tested with NX3031 adapter.
Tested-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NAndy Gospodarek <agospoda@redhat.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Included changes:
- introduction of the new Network Coding component. This new mechanism aims to
  increase throughput by fusing multiple packets in one transmission.
- minor cleanups
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes chip specific operations from the common hardware
paths, as well as the Makefile change to accomodate the new files.
Signed-off-by: NArvind Bhushan <arvindb@chelsio.com>
Signed-off-by: NNaresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch defines the common operations to support multiple chips. It
includes common header file modifications to support the current chips
(T4 and T5). It also includes the following bug fixes:
- reconfirms the rnode state after an implicit logo.
- corrects the stats array size.
- sets up and checks flags correctly when coming up as master and finding
the card initialized
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NArvind Bhushan <arvindb@chelsio.com>
Signed-off-by: NNaresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch creates a new file for T5 adapter operations.
Signed-off-by: NArvind Bhushan <arvindb@chelsio.com>
Signed-off-by: NNaresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch separates T4 adapter operations into a new file.
Signed-off-by: NArvind Bhushan <arvindb@chelsio.com>
Signed-off-by: NNaresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T5 adapter does not support onchip queue memory. Present logic fails to
allocate QP for T5 and returns an error. Also, if module parameter ocqp_support
is zero then we are unable to allocate QP which should not be the case. Ideally
if ocqp_support parameter is 0 or onchip queue support is disable then host QP
should be allocated before returning an error.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always bump the tcam_full stat. Also, bump wr reply timeout to 30 seconds.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It enables direct DMA by HW to memory region PBL arrays and fast register PBL
arrays from host memory, vs the T4 way of passing these arrays in the WR itself.
The result is lower latency for memory registration, and larger PBL array
support for fast register operations.

This patch also updates ULP_TX_MEM_WRITE command fields for T5. Ordering bit of
ULP_TX_MEM_WRITE is at bit position 22 in T5 and at 23 in T4.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both DB Flow-Control and DB Coalescing are disabled by default on T5
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for Chelsio T5 adapter.
Enables T5's Write Combining feature.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All T5 adapters will only support VFs on PF0-3 despite the ability of the
hardware to support them on PF4-7.  This keeps our T4 and T5 adapters more
similar which simplifies host driver software.
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements a low latency Write Combining (aka Write Coalescing) work
request path. PCIE maps User Space Doorbell BAR2 region writes to the new
interface to SGE. SGE pulls a new message from PCIE new interface and if its a
coalesced write work request then pushes it for processing. This patch copies
coalesced work request to memory mapped BAR2 space.
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NVipul Pandya <vipul@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When receiving a network coded packet, the decoding buffer is searched
for a packet to use for decoding. The source, destination, and crc32 from
the coded packet is used to identify the wanted packet. The decoded
packet is passed to the usual unicast receiver function, as had it never
been network coded.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

To be able to decode a network coded packet, a node must already know
one of the two coded packets. This is done by buffering skbs before
transmission and buffering packets sniffed with promiscuous mode from
other hosts.

Packets are kept in a buffer similar to the one with forward-skbs: A
hash table, where each entry, which corresponds to a src-dst pair, has a
linked list packets.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.

Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Two be able to network code two packets, one packet must be buffered
until the next is available. This is done in a "coding buffer", which is
essentially a hash table with lists of packets. Each entry in the hash
table corresponds to a specific src-dst pair, which has a linked list of
packets that are buffered.

This patch adds skbs to the buffer just before forwarding them. The
buffer is traversed every 10 ms, where timed skbs are removed from the
buffer and transmitted. To allow experiments with the network coding
scheme, the timeout is tunable through a file in debugfs.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

To use network coding efficiently, a relay must know when neighbor nodes
are likely to have enough information to be able to decode a network
coded packet. This is detected by using OGMs from batman-adv to discover
when one neighbor is in range of another neighbor. The relay check the
TLL to detect when an OGM is forwarded from one neighbor by another
neighbor, and thereby knows that the two neighbors are in range and thus
overhear packets sent by each other.

This information is saved in the orig_node struct to be used when
searching for coding opportunities. Two lists are added to the
orig_node struct: One for neighbors that can hear the orig_node
(outgoing nc_nodes) and one for neighbors that the orig_node can hear
(incoming nc_nodes).

Information about nc_nodes is kept for 10 seconds and is available
through debugfs in batman_adv/nc_nodes to use when debugging network
coding.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>