Davinci MMC platform devices (as in mach-davinci/devices-da8xx.c) use
"davinci_mmc" as their name. To allow autoloading of the relevant
driver, the module needs to set the MODULE_ALIAS.
Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

For small size non-dma sdio transactions, it is sometimes better to poll
the mmc host and avoid interrupts altogether. Polling lowers the number
of interrupts and context switches. Tests have shown that for small
transactions, only a few polling iterations are needed, so this is worth
while.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Tested-by: NRajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The davinci mmc interrupt handler fills the fifo, as long as the DXRDY
or DRRDY bits are set in the status register.

If interrupts fire during this loop, they will be handled by the
handler, but the interrupt controller will still buffer these. As a
result, the handler will be called again to serve these needlessly. In
order to avoid these spurious interrupts, keep interrupts masked while
filling the fifo.
Signed-off-by: NIdo Yariv <ido@wizery.com>
Tested-by: NRajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Most parts of the enable / disable API are no longer used and
can be removed.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Tested-by: NVenkatraman S <svenkatr@ti.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some devices connected to the MMC bus are power controlled by external
means. For instance, an SDIO device may be powered down/up by an
external gpio line.

In order to avoid toggling power from within the MMC host driver, add a
set_power callback function, which will be called by set_ios upon
powering down/up.
Signed-off-by: NIdo Yariv <ido@wizery.com>
CC: Chris Ball <cjb@laptop.org>
Acked-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch adds support for handling SDIO interrupt on DaVinci MMC/SD
controller.

The patch has been tested on DM355 and DA850 EVMs with Marvell Libertas
based SDIO wireless LAN card.
Signed-off-by: NAlagu Sankar <alagusankar@embwise.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

We have deprecated the distinction between hardware and physical
segments in the block layer.  Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core.  As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.

We might as well just delete the unused paramter.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: NSascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve the suspend and resume callbacks in DaVinci MMC host controller
driver.  Modify the reset status of the contorller and clock during
suspend and resume.  Also migrate the power management callbacks from
platform driver to dev_pm_ops structure.

Tested on DA850/OMAP-L138 EVM.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a helper function which will aid in changing the reset
status of the controller.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On some platforms like DM355, the number of EDMA parameter slots available
for EDMA_SLOT_ANY usage are few.  In such cases, if MMC/SD uses 16 slots
for each instance of MMC controller, then the number of slots available
for other modules will be very few.

By passing the number of EDMA slots to be used in MMC driver from platform
data, EDMA slots available for other purposes can be controlled.

Most of the platforms will not use this platform data variable.  But on
DM355, as the number of EDMA resources available is limited, the number of
scatter- gather segments used inside the MMC driver can be 8 (passed as
platform data) instead of 16.  On DM355, when the number of scatter-gather
segments was reduced to 8, I saw a performance difference of about
0.25-0.4 Mbytes/sec during write.  Read performance variations were
negligible.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for 8bit MMC cards.  The controller data width is configurable
depending on the wires setting in the platform data structure.

MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM.
Signed-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add cpufreq support to MMC driver. The clock divider value has to be
modified according to the controller input frequency.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently DaVinci EDMA driver supports multiple EDMA channel controller
instances.  edma_alloc_channel() api returns a 32 bit value which has the
channel controller number in MSB and the EDMA channel number in LSB.  The
variables which store the value returned by edma_alloc_channel() have to
be 32 bit wide now.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: NVipin Bhandari <vipin.bhandari@ti.com>
Cc: Purshotam Kumar <purushotam@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for MMC/SD controller driver for all DaVinci family SoC.  This
patch supports davinci family SoC's DM6446, DM355, DM365 and
DA830/OMAPL137.

The patch has been tested on DM355 EVM.

The MMCSD controller specifications for DM355 can be found at
http://focus.ti.com/general/docs/litabsmultiplefilelist.tsp?literatureNumber=spruee2cSigned-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: NPurshotam Kumar <purushotam@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>