Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 03 11月, 2013 2 次提交
    • S
      cifs: Send a logoff request before removing a smb session · 7f48558e
      由 Shirish Pargaonkar 提交于 
      Send a smb session logoff request before removing smb session off of the list.
On a signed smb session, remvoing a session off of the list before sending
a logoff request results in server returning an error for lack of
smb signature.

Never seen an error during smb logoff, so as per MS-SMB2 3.2.5.1,
not sure how an error during logoff should be retried. So for now,
if a server returns an error to a logoff request, log the error and
remove the session off of the list.
Signed-off-by: NShirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NSteve French <smfrench@gmail.com>
      7f48558e
    • T
      cifs: Make big endian multiplex ID sequences monotonic on the wire · 3d378d3f
      由 Tim Gardner 提交于 
      The multiplex identifier (MID) in the SMB header is only
ever used by the client, in conjunction with PID, to match responses
from the server. As such, the endianess of the MID is not important.
However, When tracing packet sequences on the wire, protocol analyzers
such as wireshark display MID as little endian. It is much more informative
for the on-the-wire MID sequences to match debug information emitted by the
CIFS driver.  Therefore, one should write and read MID in the SMB header
assuming it is always little endian.

Observed from wireshark during the protocol negotiation
and session setup:

        Multiplex ID: 256
        Multiplex ID: 256
        Multiplex ID: 512
        Multiplex ID: 512
        Multiplex ID: 768
        Multiplex ID: 768

After this patch on-the-wire MID values begin at 1 and increase monotonically.

Introduce get_next_mid64() for the internal consumers that use the full 64 bit
multiplex identifier.

Introduce the helpers get_mid() and compare_mid() to make the endian
translation clear.
Reviewed-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NTim Gardner <timg@tpi.com>
Signed-off-by: NSteve French <smfrench@gmail.com>
      3d378d3f
  3. 28 10月, 2013 4 次提交
  5. 15 10月, 2013 1 次提交
  7. 07 10月, 2013 3 次提交
  9. 06 10月, 2013 1 次提交
    • S
      do not treat non-symlink reparse points as valid symlinks · c31f3307
      由 Steve French 提交于 
      Windows 8 and later can create NFS symlinks (within reparse points)
which we were assuming were normal NTFS symlinks and thus reporting
corrupt paths for.  Add check for reparse points to make sure that
they really are normal symlinks before we try to parse the pathname.

We also should not be parsing other types of reparse points (DFS
junctions etc) as if they were a  symlink so return EOPNOTSUPP
on those.  Also fix endian errors (we were not parsing symlink
lengths as little endian).

This fixes commit d244bf2d
which implemented follow link for non-Unix CIFS mounts

CC: Stable <stable@kernel.org>
Reviewed-by: NAndrew Bartlett <abartlet@samba.org>
Signed-off-by: NSteve French <smfrench@gmail.com>
      c31f3307
  11. 26 9月, 2013 2 次提交
  13. 21 9月, 2013 1 次提交
  15. 18 9月, 2013 2 次提交
    • J
      cifs: stop trying to use virtual circuits · 9ae6cf60
      由 Jeff Layton 提交于 
      Currently, we try to ensure that we use vcnum of 0 on the first
established session on a connection and then try to use a different
vcnum on each session after that.

This is a little odd, since there's no real reason to use a different
vcnum for each SMB session. I can only assume there was some confusion
between SMB sessions and VCs. That's somewhat understandable since they
both get created during SESSION_SETUP, but the documentation indicates
that they are really orthogonal. The comment on max_vcs in particular
looks quite misguided. An SMB session is already uniquely identified
by the SMB UID value -- there's no need to again uniquely ID with a
VC.

Furthermore, a vcnum of 0 is a cue to the server that it should release
any resources that were previously held by the client. This sounds like
a good thing, until you consider that:

a) it totally ignores the fact that other programs on the box (e.g.
smbclient) might have connections established to the server. Using a
vcnum of 0 causes them to get kicked off.

b) it causes problems with NAT. If several clients are connected to the
same server via the same NAT'ed address, whenever one connects to the
server it kicks off all the others, which then reconnect and kick off
the first one...ad nauseum.

I don't see any reason to ignore the advice in "Implementing CIFS" which
has a comprehensive treatment of virtual circuits. In there, it states
"...and contrary to the specs the client should always use a VcNumber of
one, never zero."

Have the client just use a hardcoded vcnum of 1, and stop abusing the
special behavior of vcnum 0.
Reported-by: NSauron99@gmx.de <sauron99@gmx.de>
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Reviewed-by: NVolker Lendecke <vl@samba.org>
Signed-off-by: NSteve French <smfrench@gmail.com>
      9ae6cf60
    • D
      CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them · 54afa990
      由 David Howells 提交于 
      In cifs_readpages(), we may decide we don't want to read a page after all -
but the page may already have passed through fscache_read_or_alloc_pages() and
thus have marks and reservations set.  Thus we have to call
fscache_readpages_cancel() or fscache_uncache_page() on the pages we're
returning to clear the marks.

NFS, AFS and 9P should be unaffected by this as they call read_cache_pages()
which does the cleanup for you.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Reviewed-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NSteve French <smfrench@gmail.com>
      54afa990
  17. 17 9月, 2013 1 次提交
  19. 14 9月, 2013 2 次提交
  21. 13 9月, 2013 1 次提交
  23. 10 9月, 2013 5 次提交
  25. 09 9月, 2013 15 次提交