cpufreq_init_policy() can fail, and we don't do anything except a call
to ->exit() on that. The policy should be freed if this happens.

Do it properly.
Reported-and-tested-by: N"Jon Medhurst (Tixy)" <tixy@linaro.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

These labels are are named in two ways normally:
 - Based on what caused to jump to such labels
 - Based on what we do under such labels

We follow the first naming convention today and that leads to multiple
labels for doing the same work. Fix it by switching to the second way of
naming them.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Drivers can store their internal per-policy information in
policy->driver_data, lets use it.

we have benefits after this replacing.
1) memory saving.
2) policy is shared by several cpus, per_cpu seems not correct. using
*driver_data* is more reasonable.
3) fix a memory leak in acpi_cpufreq_cpu_exit. as policy->cpu might
change during cpu hotplug. So sometimes we cant't free *data*, use
*driver_data* to fix it.
4) fix a zero return value of get_cur_freq_on_cpu. Only per_cpu of
policy->cpu is set to *data*, if we try to get cpufreq on other cpus, we
get zero instead of correct values. Use *driver_data* to fix it.
Signed-off-by: NPan Xinhui <xinhuix.pan@intel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Users of freq table may want to access it for any CPU from
policy->related_cpus mask. One such user is cpu-cooling layer. It gets a
list of 'clip_cpus' (equivalent to policy->related_cpus) during
registration and tries to get freq_table for the first CPU of this mask.

If the CPU, for which it tries to fetch freq_table, is offline,
cpufreq_frequency_get_table() fails. This happens because it relies on
cpufreq_cpu_get_raw() for its functioning which returns policy only for
online CPUs.

The fix is to access the policy data structure for the given CPU
directly (which also returns a valid policy for offline CPUs), but the
policy itself has to be active (meaning that at least one CPU using it
is online) for the frequency table to be returned.

Because we will be using 'cpufreq_cpu_data' now, which is internal to
the cpufreq core, move cpufreq_frequency_get_table() to cpufreq.c.
Reported-and-tested-by: NPi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When all CPUs of a policy are hot-unplugged, we EXIT the governor but
don't mark policy->governor as NULL. This was done in order to keep last
used governor's information intact in sysfs, while the CPUs are offline.

But we also need to clear policy->governor when restoring the policy.

Because policy->governor still points to the last governor while policy
is restored, following sequence of event happens:
 - cpufreq_init_policy() called while restoring policy
 - find_governor() matches last_governor string for present governors and
   returns last used governor's pointer, say ondemand. policy->governor
   already has the same address, unless the governor was removed in
   between.
 - cpufreq_set_policy() is called with both old/new policies governor set
   as ondemand.
 - Because governors matched, we skip governor initialization and return
   after calling __cpufreq_governor(CPUFREQ_GOV_LIMITS). Because the
   governor wasn't initialized for this policy, it returned -EBUSY.
 - cpufreq_init_policy() exits the policy on this error, but doesn't
   destroy it properly (should be fixed separately).
 - And so we enter a scenario where the policy isn't completely
   initialized but used.

Fix this by setting policy->governor to NULL while restoring the policy.
Reported-and-tested-by: NPi-Cheng Chen <pi-cheng.chen@linaro.org>
Reported-and-tested-by: N"Jon Medhurst (Tixy)" <tixy@linaro.org>
Reported-and-tested-by: NSteven Rostedt <rostedt@goodmis.org>
Fixes: 18bf3a12 (cpufreq: Mark policy->governor = NULL for inactive policies)
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

When split BAR is enabled, the driver needs to dump out the split BAR
registers rather than the original 64bit BAR registers.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The unsafe doorbell and scratchpad access should display reason when
WARN is called.  Otherwise we get a stack dump without any explanation.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Printouts driver name and version to indicate what is being loaded.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k.  Change the driver default to 64k.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Disable DMA usage by default, since the CPU provides much better
performance with write combining.  Provide a module parameter to enable
DMA usage when offloading the memcpy is preferred.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Changing the memory window BAR mappings to write combining significantly
boosts the performance.  We will also use memcpy that uses non-temporal
store, which showed performance improvement when doing non-cached
memcpys.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Allocate memory for the NUMA node of the NTB device.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Allocate memory and request the DMA channel for the same NUMA node as
the NTB device.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

When the ntb transport is connecting and waiting for the peer, the debug
console receives lots of debug level messages about the remote qp link
status being down.  Rate limit those messages.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

This is a simple debugging driver that enables the doorbell and
scratch pad registers to be read and written from the debugfs.  This
tool enables more complicated debugging to be scripted from user space.
This driver may be used to test that your ntb hardware and drivers are
functioning at a basic level.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

This is a simple ping pong driver that exercises the scratch pads and
doorbells of the ntb hardware.  This driver may be used to test that
your ntb hardware and drivers are functioning at a basic level.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Reset the link stats when the link goes down.  In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them.  Reset
all the stats, to be consistent.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

On link down, don't advance RX index to the next entry.  The next entry
should never be valid after receiving the link down flag.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport.  Change the messages so they are distinct.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen.  Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer.  The transport expects the peer values to be
the same as the local values, so this issue was not obvious.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Change ntb_hw_intel to use the new NTB hardware abstraction layer.

Split ntb_transport into its own driver.  Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The length of each EDID block is EDID_LENGTH, and number of blocks is
(1 + edid->extensions) - we need to multiply not add them.

This causes wrong EDID to be passed on, and is a regression introduced
by d2ed3436 (drm: Introduce helper for replacing blob properties)
Signed-off-by: NShixin Zeng <zeng.shixin@gmail.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Stone <daniels@collabora.com>
[danvet: Add Cc: and fix commit summary.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Eric noticed problems with vhost-scsi and virtio-ccw: vhost-scsi
complained about overwriting values in the config space, which
was triggered by a broken implementation of virtio-ccw's config
get/set routines. It was probably sheer luck that we did not hit
this before.

When writing a value to the config space, the WRITE_CONF ccw will
always write from the beginning of the config space up to and
including the value to be set. If the config space up to the value
has not yet been retrieved from the device, however, we'll end up
overwriting values. Keep track of the known config space and update
if needed to avoid this.

Moreover, READ_CONF will only read the number of bytes it has been
instructed to retrieve, so we must not copy more than that to the
buffer, or we might overwrite trailing values.
Reported-by: NEric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NEric Farman <farman@linux.vnet.ibm.com>
Tested-by: NEric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Use kernel.h macro definition.

Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

Add pwm[4-7] and the associated pwm[4-7]_mode attributes.
Signed-off-by: NRoger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

Revert commit ff284f37 (Revert "ACPICA: Permanently set _REV to
the value '2'.) as the regression introduced by commit b1ef2972
reverted by it is now addressed via a blacklist entry.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The platform firmware on some systems expects Linux to return "5" as
the supported ACPI revision which makes it expose system configuration
information in a special way.

For example, based on what ACPI exports as the supported revision,
Dell XPS 13 (2015) configures its audio device to either work in HDA
mode or in I2S mode, where the former is supposed to be used on Linux
until the latter is fully supported (in the kernel as well as in user
space).

Since ACPI 6 mandates that _REV should return "2" if ACPI 2 or later
is supported by the OS, a subsequent change will make that happen, so
make it possible to override that on systems where "5" is expected to
be returned for Linux to work correctly one them (such as the Dell
machine mentioned above).
Original-by: NDominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

At the moment the IRQCHIP_DECLARE macro is only declared locally in
drivers/irqchip/irqchip.h. It prevents from using it directly in arch/*
directories whenever irqchip drivers only exist there, which happens in a few
cases (e.g. arc, arm, microblaze and mips).

This patch makes the macro to be globally defined, i.e. in
include/linux/irqchip.h, and thus usable for arch-specific declarations of
irqchip drivers. In this way, it is very similar to what clocksource does (ie
CLOCKSOURCE_OF_DECLARE is defined in include/linux/clocksource.h).

For now, this patch only moves the declaration of the macro
IRQCHIP_DECLARE to the global header 'include/linux/irqchip.h' and make
'drivers/irqchip/irqchip.h' include 'include/linux/irqchip.h'. Later, other
patches will get rid of 'drivers/irqchip/irqchip.h' and modify all the impacted
irqchip drivers.
Signed-off-by: NJoel Porquet <joel@porquet.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1435865565-14114-1-git-send-email-joel@porquet.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Fixes an issue when queue_reuest_irq fails in nvme_setup_io_queues. This
patch initializes all vectors to -1 and resets the vector to -1 in the
case of a failure in queue_request_irq. This avoids the free_irq in
nvme_suspend_queue if the queue did not get an irq.
Signed-off-by: NJon Derrick <jonathan.derrick@intel.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer.  Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: NAllen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

After the commit 736e60dd ("OMAPDSS:
componentize omapdss") the dss core device will wait until all the
subdevices have been successfully probed. However, we don't have a
working driver for RFBI, so if RFBI device exists, omapdss will never
get probed.

All the .dtsi files set RFBI as disabled, except am4372.dtsi. This
causes omapdss probe to not finish on AM4 devices.

This patch makes omapdss driver skip adding rfbi device as a
subcomponent, solving the issue.

This should be reverted when we have a working RFBI driver.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: NFelipe Balbi <balbi@ti.com>

Commit

  debe6a62 ("MIPS: OCTEON: Update octeon-model.h code for new SoCs.")

renamed some SoC model helper functions, but forgot to update the EDAC
drivers resulting in build failures. Fix that.

Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: NDavid Daney <david.daney@cavium.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1435747132-10954-1-git-send-email-aaro.koskinen@nokia.comSigned-off-by: NBorislav Petkov <bp@suse.de>

ACPICA commit 1a8ec7b83d55c7b957247d685bd1c73f6a012f1e

Remove redundant comment in nseval.c

Link: https://github.com/acpica/acpica/commit/1a8ec7b8Signed-off-by: Ngongzg <gongzhaogang@inspur.com>
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

ACPICA commit f51bf8497889a94046820639537165bbd7ccdee6

Adds acclib.h

This patch doesn't affect the Linux kernel.

Link: https://github.com/acpica/acpica/commit/f51bf849Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLv Zheng <lv.zheng@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>