This patch makes the driver log link speed change. Before applying the
patch link messages were printed only on state change. Now message is
printed when link is brought up or down and when speed changes.

Change-ID: Ifbee14b4b16c24967450b3cecac6e8351dcc8f74
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes an X722 informational message so that it only
appears when extra messages are desired.  Without this patch,
on X722 devices, this message appears at load, potentially causing
unnecessary alarm.

Change-ID: I94f7aae15dc5b2723cc9728c630c72538a3e670e
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous workaround added to ensure receipt of all broadcast frames
incorrectly set the broadcast promiscuous mode unconditionally
regardless of active VLAN status.

Replace this partial workaround with a complete solution that sets the
broadcast promiscuous filters in i40e_sync_vsi_filters. This new method
sets the promiscuous mode based on when broadcast filters are added or
removed.

I40E_VLAN_ANY will request a broadcast filter for all VLANs, (as we're
in untagged mode) while a broadcast filter on a specific VLAN will only
request broadcast for that VLAN.

Thus, we restore addition of broadcast filter to the array, but we add
special handling for these such that they enable the broadcast
promiscuous mode instead of being sent as regular filters.

The end result is that we will correctly receive all broadcast packets
(even those with a *source* address equal to the broadcast address) but
will not receive packets for which we don't have an active VLAN filter.

Change-ID: I7d0585c5cec1a5bf55bf533b42e5e817d5db6a2d
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the problem where the ethtool Supported link
modes list backplane interfaces on X722 devices for 10GbE with
SFP+ and Cortina retimer. This patch fixes the problem by setting
and using a flag for this particular device since the backplane
interface is only between the internal PHY and the retimer and it
should not be seen by the user as they cannot use it.
Without this patch, the user wrongly thinks that backplane interfaces
are supported on their device when they actually are not.

Change-ID: I3882bc2928431d48a2db03a51a713a1f681a79e9
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A comment incorrectly referred to i40e_vsi_sync_filters_subtask which
does not actually exist. Reference the correct function instead.

Change-ID: I6bd805c605741ffb6fe34377259bb0d597edfafd
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace a check of magic number 4095 with VLAN_N_VID. This
makes it obvious that a later check against VLAN_N_VID is
always true and can be removed.

Change-ID: I28998f127a61a529480ce63d8a07e266f6c63b7b
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we are much more robust about defining what we
can and cannot offload.  Previously we were just checking for the L4 tunnel
header length, however there are other fields we should be verifying as
there are multiple scenarios in which we cannot perform hardware offloads.

In addition the device only supports GSO as long as the MSS is 64 or
greater.  We were not checking this so an MSS less than that was resulting
in Tx hangs.

Change-ID: I5e2fd5f3075c73601b4b36327b771c64fcb6c31b
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

Removed some of unnecessary if statements and unreachable code found by
static code analysis tool.
The return value of i40e_vsi_control_rings(..., false) is always 0. So,
test for non-zero will never be true. The function has been split into
"int i40e_vsi_start_rings()" and "void i40e_vsi_stop_rings()" for better
understanding.
Similarly, the function i40e_vsi_kill_vlan() never fails. So, checking
for return value is also unnecessary. Function definition changed to void.
The i40e_loopback_test() function is not implemented. The function and
all references to loopback testing were removed.

Change-ID: Id45cf66f6689ce2bc4e887de13f073e30e8431bd
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a common method for finding a VSI by type.  The main
motivation for doing this is that the Flow Director path actually had two
ways of handling this, one stopped on first match and one did not.  This
patch makes it so that all callers of this function will get the same
approach for finding a VSI.

Change-ID: Ibf25de8acd8466582520694424aa87da66965fbd
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We duplicate some code around adding and deleting filters using the
adminq interface. This is prone to errors in case there are bugs. Use
functions which extract the logic to their own portion so that we don't
duplicate it twice in code.

Change-ID: I60d68aeb887976787dec00b23ab386a106e61465
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We determine that a VSI is in vlan_mode whenever it has any filters
with a VLAN other than -1 (I40E_VLAN_ALL). The previous method of doing
so was to perform a loop whenever we needed the check. However, we can
notice that only place where filters are added (i40e_add_filter) can
change the condition from false to true, and the only place we can
return to false is in i40e_vsi_sync_filters_subtask. Thus, we can remove
the loop and use a boolean directly.

Doing this avoids looping over filters repeatedly especially while we're
already inside a loop over all the filters. This should reduce the
latency of filter operations throughout the driver.

Change-ID: Iafde08df588da2a2ea666997d05e11fad8edc338
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there exists a bug where adding at least one VLAN and then
removing all VLANs leaves the mac filters for the VSI with an incorrect
value for 'vid' which indicates the mac filter's VLAN status.

The current implementation for handling the removal of VLANs is wrong
for a couple reasons. The first is that when i40e_vsi_kill_vlan
iterates through the MAC filters, it fails to account for the MAC filter
status; i.e. it's not accommodating for filters that are about to be
deleted. The second problem is that MAC filters can be deleted in other
places (specifically i40e_set_rx_mode). Thus if it occurs that all the
VLAN MAC filters get deleted we need to switch out of VLAN mode, but the
code path through i40e_vsi_kill_vlan has already been executed and we're
now stuck in VLAN mode.

This patch fixes the issue by removing the check from i40e_vsi_kill_vlan
and puts the check instead in i40e_sync_vsi_filters where we're
guaranteed to see all filter deletions and can properly detect when we
need to switch out of VLAN mode.

Change-ID: Ib38fe6034b356eee9a0e20b8a9eeed5ff2debcd9
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, we fail to correctly restore filters on the temporary add
list when we fail to allocate memory either for deletion or addition.
Replace calls to "goto out;" with calls to a new location that correctly
handles memory allocation failures.

Note that it is safe for us to call i40e_undo_filter_entries on the
tmp_del_list even after we've deleted filters because at this point it
will be empty, so we don't need to separate the logic for add and
delete failure.

Change-Id: Iee107fd219c6e03e2fd9645c2debf8e8384a8521
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace the mac_filter_list with a static size hash table of 8bits. The
primary advantage of this is a decrease in latency of operations related
to searching for specific MAC filters, including .set_rx_mode. Using
a linked list resulted in several locations which were O(n^2). Using
a hash table should give us latency growth closer to O(n*log(n)).

Change-ID: I5330bd04053b880e670210933e35830b95948ebb
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>

When inside a loop where we call i40e_del_filter we use an O(n^2)
pattern where i40e_del_filter calls i40e_find_filter for us. We can
avoid this O(n^2) logic by factoring a function, __i40e_del_filter() out
from the i40e_del_filter code. This allows us to re-use the delete logic
where appropriate without having to search for the filter twice.

This new function benefits several functions including i40e_vsi_add_vlan,
i40e_vsi_kill_vlan, i40e_del_mac_vlan_all, and i40e_vsi_release.

Change-ID: I75fabe0f53bf73f56b80d342e5fdcfcc28f4d3eb
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When adding new MAC address filters, the driver determines if it should
behave in VLAN mode (where all MAC addresses get assigned to every
existing VLAN) or in non-VLAN mode where MAC addresses get assigned the
VLAN_ANY identifier. Under some circumstances it is possible that a VLAN
has been marked for removal (such that all filters of that VLAN are set
to I40E_FILTER_REMOVE), and a subsequent call to i40e_put_mac_in_vlan
may occur prior to the driver subtask that syncs filters to the
hardware.

In this case, we may add filters to the new removed VLAN, even though it
should have been removed. This is most obvious when first adding a new
VLAN. We will delete all filters which are in I40E_VLAN_ANY (-1) and
then re-add them as in VLAN 0 (untagged). Then before we sync filters,
we will add new MAC address filter, which will be added to every VLAN
that exists. Unfortunately, this will include I40E_VLAN_ANY, so we will
end up incorrectly adding filters to the -1 VLAN. This can be fixed by
simply skipping all filters which are marked for removal.

A similar check is not necessary in i40e_del_mac_all_vlan, since we are
deleting, and any filter which we find already marked for removal would
simply be deleted again, which doesn't cause any issues.

Change-Id: I7962154013ce02fe950584690aeeb3ed853d0086
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a PVID has been assigned to a VSI, the function
i40e_put_mac_in_vlan arbitrarily modifies all filters
to have the same VLAN. This is obviously incorrect
because it could be modifying active filters without
putting them into the NEW state. The correct method
is to remove then re-add filters which is already done
in the code where we assign the PVID.

Fix this issue and a few other minor nits at the same
time. First, when we have a PVID don't even bother
looping and simply add the filter with the PVID immediately.

In the case of the loop, we now can remove several checks.
We also don't need to use i40e_find_filter first before
calling i40e_add_filter, since i40e_add_filter implicitly
does a lookup already.

Finally, update the return semantics of this function so
that on failure to add a filter it returns NULL, but on
success, it returns the last filter added. Otherwise,
we're just returning the last filter in the list. An
alternative fix might be to return 0 or an error code,
but this is pretty invasive to every call site.

Change-ID: I2325dfd843aec76d89fb0d7cb0e7c4f290a34840
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A future patch will be modifying these functions and making a call to
a static function which currently is defined after these functions. Move
them in a separate patch to ease review and ensure the moved code is
correct.

Change-ID: I2ca7fd4e10c0c07ed2291db1ea41bf5987fc6474
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel provides __dev_uc_sync and __dev_mc_sync in order for drivers
which need individual notification of add and delete for each filter.
These functions allow us to vastly simplify our .set_rx_mode handler. We
need to implement two functions for sync and unsync which add and remove
filters respectively.

This change avoids a very complex and inefficient algorithm which
resulted in an abnormal latency for the .set_rx_mode NDO operation. The
resulting code after this change is more readable, more efficient, and
less code.

Due to the callback signature used by these functions we also must
update several other functions to take a const u8 * pointer.

Change-Id: I2ca7fd4e10c0c07ed2291db1ea41bf5987fc6474
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Originally the is_vf and is_netdev fields were added in order to
distinguish between VF and netdev filters in a single VSI. However, it
can be noted that we use separate VSI for SRIOV VFs and for netdev VSI.
Thus, since a single VSI should only ever have one type of filter, we
can simply remove the checks and remove the typing.

In a similar fashion, we can note that the only remaining way to get
multiple filters of a single type is through a debug command that was
added to debugfs. This command is useless in practice, and results in
causing bugs if we keep counter tracking but lose the is_vf and
is_netdev protections as desired above.

Since the only time we'd actually have a counter value besides 0 and
1 is through use of this debugfs hook, we can remove this unnecessary
command, and the entire counter logic it required.

We vastly simplify mac filters by removing

(a) the distinction between VF and netdev filters
(b) counting logic
(c) the ability to add and remove filters bypassing the stack via debugfs

Change-ID: Idf916dd2a1159b1188ddbab5bef6b85ea6bf27d9
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

So the i40e driver had a really convoluted configuration for how to handle
the debug flags contained in msg_level.  Part of the issue is that the
driver has its own 32 bit mask that it was using to track a separate set of
debug features.  From what I can tell it was trying to use the upper 4 bits
to determine if the value was meant to represent a bit-mask or the numeric
value provided by debug level.

What this patch does is clean this up by compressing those 4 bits into bit
31, as a result we just have to perform a check against the value being
negative to determine if we are looking at a debug level (positive), or a
debug mask (negative).  The debug level will populate the msg_level, and
the debug mask will populate the debug_mask in the hardware struct.

I added similar logic for ethtool.  If the value being provided has bit 31
set we assume the value being provided is a debug mask, otherwise we assume
it is a msg_enable mask.  For displaying we only provide the msg_enable,
and if debug_mask is in use we will print it to the dmesg log.

Lastly I removed the debugfs interface.  It is redundant with what we
already have in ethtool and really doesn't belong anyway.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Patch a036244c "i40e: Fix kernel panic on enable/disable LLDP"
introduced an error in bit logic.

Originally this bit manipulation was meant to clear two bits to indicate
that DCB was not enabled or capable. An "&" was incorrectly used instead
of an "|" bit operator to combine the two bitmasks into one.  This also
created a static checker error since the resultant code was a no-op.

This patch fixes the error by using the correct bit-wise operator.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is code refactoring. This patch removes the workaround which deleted
a default MAC filter added by the firmware when the interface was brought
up. This filter caused frames to pass disregarding the VLAN tagging.
It used to be automatically applied after reset in pre-SRA FW versions.
This workaround is not needed in production NICs and hence can be removed.

Change-ID: I129fe1aae1f17b5a224c9b29a996d916aa1be1ec
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Ethtool -L option with the combined parameter is for changing the number of
multi-purpose channels of the specified network device. The pre-set maximum
for the combined channels is cpu dependent. Currently, for an i40e device,
when the user sets a value between 64 and the maximum that the cpu can
support for the combined parameter, the i40e driver displays the confusing
info in dmesg to only show 64 as the RSS count regardless of what the
accepted user input is as long as it is larger than 64.

This patch fixes the message in the i40e driver when the user uses
ethtool -L to change the number of the combined channels to consistently
display the user requested value if it is valid and accepted by ethtool.

Change-ID: Ia80a68bc844b779a49e0f76e7d3dcc915032d9af
Signed-off-by: NLihong Yang <lihong.yang@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There exists a bug in which a 'perfect storm' can occur and cause
interrupts to fail to be correctly affinitized. This causes unexpected
behavior and has a substantial impact on performance when it happens.

The bug occurs if there is heavy traffic, any number of CPUs that have
an i40e interrupt are pegged at 100%, and the interrupt afffinity for
those CPUs is changed.  Instead of moving to the new CPU, the interrupt
continues to be polled while there is heavy traffic.

The bug is most readily realized as the driver is first brought up and
all interrupts start on CPU0. If there is heavy traffic and the
interrupt starts polling before the interrupt is affinitized, the
interrupt will be stuck on CPU0 until traffic stops. The bug, however,
can also be wrought out more simply by affinitizing all the interrupts
to a single CPU and then attempting to move any of those interrupts off
while there is heavy traffic.

This patch fixes the bug by registering for update notifications from
the kernel when the interrupt affinity changes. When that fires, we
cache the intended affinity mask. Then, while polling, if the cpu is
pegged at 100% and we failed to clean the rings, we check to make sure
we have the correct affinity and stop polling if we're firing on the
wrong CPU.  When the kernel successfully moves the interrupt, it will
start polling on the correct CPU. The performance impact is minimal
since the only time this section gets executed is when performance is
already compromised by the CPU.

Change-ID: I4410a880159b9dba1f8297aa72bef36dca34e830
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Order of arguments is wrong.
The wrong code has been introduced by commit 7d4f8d87, but is compiled
only since commit 9df70b66.

Note that this may break netlink dumps.

Fixes: 9df70b66 ("i40e: Remove incorrect #ifdef's")
Fixes: 7d4f8d87 ("switchdev; add VLAN support for port's bridge_getlink")
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NHuaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we fail on allocating enough MSI-X interrupts, we should disable
them since they were previously enabled in this point of code.

Not disabling them can lead to WARN_ON() being triggered and subsequent
failure in enabling MSI as a fallback; the below message was shown without
this patch while we played with interrupt allocation in i40e driver:

[ 21.461346] sysfs: cannot create duplicate filename '/devices/pci0007:00/0007:00:00.0/0007:01:00.3/msi_irqs'
[ 21.461459] ------------[ cut here ]------------
[ 21.461514] WARNING: CPU: 64 PID: 1155 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x88/0xc0

Also, we noticed that without this patch, if we modprobe the module without
enough MSI-X interrupts (triggering the above warning), unload the module
and re-load it again, we got a crash on the system.
Signed-off-by: NGuilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

in commit a036244c a fix
was put into place to avoid a kernel panic when a non-
supported traffic class configuration was put into place
and then lldp was enabled/disabled on the link partner
switch.  This fix caused it to be necessary to
unload/reload the driver to reenable DCB once a supported
TC config was in place.

The root cause of the original panic was that the function
i40e_pf_get_default_tc was allowing for a default TC other
than TC 0, and only TC 0 is supported as a default.

This patch removes the get_default_tc function and replaces
it with a #define since there is only one TC supported as
a default.

Change-Id: I448371974e946386d0a7718d73668b450b7c72ef
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NRonald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e100: min_mtu 68, max_mtu 1500
- remove e100_change_mtu entirely, is identical to old eth_change_mtu,
  and no longer serves a purpose. No need to set min_mtu or max_mtu
  explicitly, as ether_setup() will already set them to 68 and 1500.

e1000: min_mtu 46, max_mtu 16110

e1000e: min_mtu 68, max_mtu varies based on adapter

fm10k: min_mtu 68, max_mtu 15342
- remove fm10k_change_mtu entirely, does nothing now

i40e: min_mtu 68, max_mtu 9706

i40evf: min_mtu 68, max_mtu 9706

igb: min_mtu 68, max_mtu 9216
- There are two different "max" frame sizes claimed and both checked in
  the driver, the larger value wasn't relevant though, so I've set max_mtu
  to the smaller of the two values here to retain identical behavior.

igbvf: min_mtu 68, max_mtu 9216
- Same issue as igb duplicated

ixgb: min_mtu 68, max_mtu 16114
- Also remove pointless old == new check, as that's done in dev_set_mtu

ixgbe: min_mtu 68, max_mtu 9710

ixgbevf: min_mtu 68, max_mtu dependent on hardware/firmware
- Some hw can only handle up to max_mtu 1504 on a vf, others 9710

CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although rare, it's possible to hit PCI error early on device
probe, meaning possibly some structs are not entirely initialized,
and some might even be completely uninitialized, leading to NULL
pointer dereference.

The i40e driver currently presents a "bad" behavior if device hits
such early PCI error: firstly, the struct i40e_pf might not be
attached to pci_dev yet, leading to a NULL pointer dereference on
access to pf->state.

Even checking if the struct is NULL and avoiding the access in that
case isn't enough, since the driver cannot recover from PCI error
that early; in our experiments we saw multiple failures on kernel
log, like:

  [549.664] i40e 0007:01:00.1: Initial pf_reset failed: -15
  [549.664] i40e: probe of 0007:01:00.1 failed with error -15
  [...]
  [871.644] i40e 0007:01:00.1: The driver for the device stopped because the
  device firmware failed to init. Try updating your NVM image.
  [871.644] i40e: probe of 0007:01:00.1 failed with error -32
  [...]
  [872.516] i40e 0007:01:00.0: ARQ: Unknown event 0x0000 ignored

Between the first probe failure (error -15) and the second (error -32)
another PCI error happened due to the first bad probe. Also, driver
started to flood console with those ARQ event messages.

This patch will prevent these issues by allowing error recovery
mechanism to remove the failed device from the system instead of
trying to recover from early PCI errors during device probe.

CC: <stable@vger.kernel.org>
Signed-off-by: NGuilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently if the MSI-X vector limit is reached the sideband flow
director gets disabled. A bit too early to make that decision, as
vectors may get re-distributed. So move the check further back.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver allocates 1 vector per CPU thread and the current hardware
limit for vectors is 129 per PF. On systems with 128 or more threads
this currently means all vectors are used by the PF leaving no room for
additional features like VMDq, iWARP, etc...
The code that should redistribute the vectors in this case is broken and
never triggers. Fixed the code so that it actually triggers if the
hardware limit is reached and adjust the number of queue pairs
accordingly.
Also the number of initially requested iWARP vectors was not properly
saved when the vector limit was reached, and therefore always zero.

Comparison with debug statement.
Before:
i40e 0000:2d:00.0: VMDq disabled, not enough MSI-X vectors
i40e 0000:2d:00.0: IWARP disabled, not enough MSI-X vectors
i40e 00.0 MSI-X vector distribution: PF 128, VMDq 0, FDSB 0, iWARP 0
After:
i40e 0000:2d:00.0: MSI-X vector limit reached, attempting to redistribute vectors
i40e 00.0 MSI-X vector distribution: PF 78, VMDq 8, FDSB 0, iWARP 42
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During MSI-X vector allocation for VMDq, a check for "no vectors left"
was missing, add it. This prevents more vectors to be allocated than
available.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some rare cases, we might get a VSI with no queues. In this case, we
cannot configure RSS on this VSI as it will try to divide by zero when
configuring the lookup table.

Change-ID: I6ae173a7dd3481a081e079eb10eb80275de2adb0
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The return value from i40e_shutdown_adminq() is always 0
(I40E_SUCCESS). So, the test for non-0 will never be true. Cleanup
by removing the test and debug print statement.

Change-ID: Ie51e8e37515c3e3a6a9ff26fa951d0e5e24343c1
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In i40e_fdir_check_and_reenable(), the driver performs some checks to
determine whether it is safe to re-enable FD Sideband and FD ATR
support. The current check will only determine if there is available
space in the flow director table. However, this ignores the fact that
ATR should be disabled when there are TCP/IPv4 sideband rules in effect.
Add the missing check, and update the info message printed when
I40E_DEBUG_FD is enabled.

Change-ID: Ibb9c63e5be95d63c53a498fdd5dbf69f54a00e08
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.

Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.

Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.

Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>