The Amlogic SoC embeds a standalone CEC controller, this patch adds a driver
for such controller.
The controller does not need HPD to be active, and could support up to max
5 logical addresses, but only 1 is handled since the Suspend firmware can
make use of this unique logical address to wake up the device.

The Suspend firmware configuration will be added in an other patchset.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com:s/if (ret)/if (res)/ to fix obvious typo]
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This adds Venus driver Makefile and changes v4l2 platform
Makefile/Kconfig in order to enable building of the driver.

Note that in this initial version the COMPILE_TEST-ing is not
supported because the drivers specific to ARM builds are still
in process of enabling the aforementioned compile testing.
Once that disadvantage is fixed the Venus driver compile testing
will be possible with follow-up changes.
Signed-off-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This driver can handle SoC internal and external video bus multiplexers,
controlled by mux controllers provided by the mux controller framework,
such as MMIO register bitfields or GPIOs. The subdevice passes through
the mbus configuration of the active input to the output side.

Since the mux framework is not yet merged, this driver contains
temporary mmio-mux support to work without the framework. The driver
should be converted to use the multiplexer API once the "mux: minimal
mux subsystem" and "mux: mmio-based syscon mux controller" patches are
merged.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NSteve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NPavel Machek <pavel@ucw.cz>
[hans.verkuil@cisco.com: add 'select REGMAP' to Kconfig]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch adds Digital Radio Interface (DRIF) support to R-Car Gen3 SoCs.
The driver exposes each instance of DRIF as a V4L2 SDR device. A DRIF
device represents a channel and each channel can have one or two
sub-channels respectively depending on the target board.

DRIF supports only Rx functionality. It receives samples from a RF
frontend tuner chip it is interfaced with. The combination of DRIF and the
tuner device, which is registered as a sub-device, determines the receive
sample rate and format.

In order to be compliant as a V4L2 SDR device, DRIF needs to bind with
the tuner device, which can be provided by a third party vendor. DRIF acts
as a slave device and the tuner device acts as a master transmitting the
samples. The driver allows asynchronous binding of a tuner device that
is registered as a v4l2 sub-device. The driver can learn about the tuner
it is interfaced with based on port endpoint properties of the device in
device tree. The V4L2 SDR device inherits the controls exposed by the
tuner device.

The device can also be configured to use either one or both of the data
pins at runtime based on the master (tuner) configuration.
Signed-off-by: NRamesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: NHans Verkuil <hansverk@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch add cec driver for STM32 platforms.
cec hardware block isn't not always used with hdmi so
cec notifier is not implemented. That will be done later
when STM32 DSI driver will be available.

Driver compliance has been tested with cec-ctl and cec-compliance
tools.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NYannick Fertre <yannick.fertre@st.com>
[hans.verkuil@cisco.com: modified platform/Makefile to use obj-y]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Depending on arch configs to include dirs is evil, and makes
harder to change drivers to work with COMPILE_TEST.

Replace them by obj-y.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This V4L2 subdev driver enables Digital Camera Memory Interface (DCMI)
of STMicroelectronics STM32 SoC series.
Signed-off-by: NYannick Fertre <yannick.fertre@st.com>
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

First version of the Virtual Media Controller.
Add a simple version of the core of the driver, the capture and
sensor nodes in the topology, generating a grey image in a hardcoded
format.
Signed-off-by: NHelen Koike <helen.koike@collabora.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix small typo in Kconfig]
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.

Update the bindings documenting the new hdmi phandle and
update exynos4.dtsi accordingly.

Tested with my Odroid U3.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NKrzysztof Kozlowski <krzk@kernel.org>
CC: linux-samsung-soc@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

By using the CEC notifier framework there is no longer any reason
to manually set the physical address. This was the one blocking
issue that prevented this driver from going out of staging, so do
this move as well.
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Move this out of the soc_camera directory into the atmel directory
where it belongs.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add v4l2 driver for Mediatek JPEG Decoder
Signed-off-by: NRick Chang <rick.chang@mediatek.com>
Signed-off-by: NMinghsiu Tsai <minghsiu.tsai@mediatek.com>
Reviewed-by: NRicky Liang <jcliang@chromium.org>
Tested-by: NRicky Liang <jcliang@chromium.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This V4L2 driver enables DELTA multi-format video decoder
of STMicroelectronics STiH4xx SoC series.
Acked-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The FDP1 driver performs advanced de-interlacing on a memory 2 memory
based video stream, and supports conversion from YCbCr/YUV
to RGB pixel formats
Signed-off-by: NKieran Bingham <kieran+renesas@bingham.xyz>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add MDP driver for MT8173
Signed-off-by: NMinghsiu Tsai <minghsiu.tsai@mediatek.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Linking soc_mediabus into this driver causes multiple definition linker warnings
if soc_camera is also enabled:

   drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_image_size+0x0): multiple definition of `__ksymtab_soc_mbus_image_size'
   drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_image_size+0x0): first defined here
>> drivers/media/platform/soc_camera/built-in.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): multiple definition of `__ksymtab_soc_mbus_samples_per_pixel'
   drivers/media/platform/soc_camera/soc_mediabus.o:(___ksymtab+soc_mbus_samples_per_pixel+0x0): first defined here
   drivers/media/platform/soc_camera/built-in.o: In function `soc_mbus_config_compatible':
   (.text+0x3840): multiple definition of `soc_mbus_config_compatible'
   drivers/media/platform/soc_camera/soc_mediabus.o:(.text+0x134): first defined here

Since we really don't want to have to use any of the soc-camera code this patch
copies the relevant code and data structures from soc_mediabus and renames it to pxa_mbus_*.

The large table of formats has been culled a bit, removing formats that are not supported
by this driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As the conversion to a v4l2 standalone device is finished, move
pxa_camera one directory up and finish severing any dependency to
soc_camera.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch adds V4L2 HVA (Hardware Video Accelerator) video encoder
driver for STMicroelectronics SoC. It uses the V4L2 mem2mem framework.

This patch only contains the core parts of the driver:
- the V4L2 interface with the userland (hva-v4l2.c)
- the hardware services (hva-hw.c)
- the memory management utilities (hva-mem.c)

This patch doesn't include the support of specific codec (e.g. H.264)
video encoding: this support is part of subsequent patches.
Signed-off-by: NYannick Fertre <yannick.fertre@st.com>
Signed-off-by: NJean-Christophe Trotin <jean-christophe.trotin@st.com>
Acked-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The s5p-tv driver has been replaced by the exynos drm driver for quite a
long time now. Remove this driver to avoid having duplicate drivers,
of which this one is considered dead code by Samsung.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add driver for the Image Sensor Controller. It manages
incoming data from a parallel based CMOS/CCD sensor.
It has an internal image processor, also integrates a
triple channel direct memory access controller master
interface.
Signed-off-by: NSongjun Wu <songjun.wu@microchip.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add v4l2 layer encoder driver for MT8173
Signed-off-by: NTiffany Lin <tiffany.lin@mediatek.com>
[hans.verkuil@cisco.com: drop unnecessary ARM || ARM64 dependency]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The VPU driver for hw video codec embedded in Mediatek's MT8173 SOCs.
It is able to handle video decoding/encoding of in a range of formats.
The driver provides with VPU firmware download, memory management and
the communication interface between CPU and VPU.
For VPU initialization, it will create virtual memory for CPU access and
IOMMU address for vcodec hw device access. When a decode/encode instance
opens a device node, vpu driver will download vpu firmware to the device.
A decode/encode instant will decode/encode a frame using VPU
interface to interrupt vpu to handle decoding/encoding jobs.
Signed-off-by: NAndrew-CT Chen <andrew-ct.chen@mediatek.com>
Signed-off-by: NTiffany Lin <tiffany.lin@mediatek.com>
[hans.verkuil@cisco.com: drop unnecessary ARM || ARM64 dependency]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As the CEC core is currently at staging, it doesn't make any sense
to put a dependent driver outside staging. So, move it also to
staging.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add CEC interface driver present in the Samsung Exynos range of
SoCs.

The following files were based on work by SangPil Moon:
- exynos_hdmi_cec.h
- exynos_hdmi_cecctl.c
Signed-off-by: NKamil Debski <kamil@wypas.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The FCP is a companion module of video processing modules in the
Renesas R-Car Gen3 SoCs. It provides data compression and decompression,
data caching, and conversion of AXI transactions in order to reduce the
memory bandwidth.

The driver is not meant to be used standalone but provides an API to the
video processing modules to control the FCP.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

A V4L2 driver for Renesas R-Car VIN driver that do not depend on
soc_camera. The driver is heavily based on its predecessor and aims to
replace it.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The Timberdale FPGA video driver has not seen any real development
since 2011 (and very little before that).

One of the problems with the timblogiw driver is that it uses videobuf
instead of the newer vb2 framework. The long term goal is to either
convert or remove any driver still using videobuf. Since none of the
core v4l developers has the hardware, we cannot convert it ourselves.

As far as I can tell it was only used in an Intel demo board in 2009
using Meego:

http://www.chinait.com/intelcontent/intelprc/admin/PDFFile/20106411545.pdf

which has since been superseded.

Moving this driver to staging is the first step towards removal. After 2 or
3 kernel cycles it will be removed altogether unless someone steps up to
clean up this driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NRichard Röjfors <richard@puffinpack.se>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The Camera Adaptation Layer (CAL) is a block which consists of a dual
port CSI2/MIPI camera capture engine.
Port #0 can handle CSI2 camera connected to up to 4 data lanes.
Port #1 can handle CSI2 camera connected to up to 2 data lanes.
The driver implements the required API/ioctls to be V4L2 compliant.
Driver supports the following:
    - V4L2 API using DMABUF/MMAP buffer access based on videobuf2 api
    - Asynchronous sensor sub device registration
    - DT support
Signed-off-by: NBenoit Parrot <bparrot@ti.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds the Kconfig and Makefile for the c8sectpfe driver
so it will be built. It also selects additional demodulator and tuners
which are required by the supported NIM cards.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Here's the driver for the Renesas R-Car JPEG processing unit.

The driver is implemented within the V4L2 framework as a memory-to-memory
device.  It presents two video nodes to userspace, one for the encoding part,
and one for the decoding part.

It was found that the only working mode for encoding is no markers output, so we
generate markers with software. In the current version of driver we also use
software JPEG header parsing because with hardware parsing performance is lower
than desired.

>From a userspace point of view the process is typical (S_FMT, REQBUF,
optionally QUERYBUF, QBUF, STREAMON, DQBUF) for both the source and destination
queues. STREAMON can return -EINVAL in case of mismatch of output and capture
queues format. Also during decoding driver can return buffers if queued
buffer with JPEG image contains image with inappropriate subsampling (e.g.
4:2:0 in JPEG and 4:2:2 in capture).  If JPEG image and queue format dimensions
differ driver will return buffer on QBUF with VB2_BUF_STATE_ERROR flag.

During encoding the available formats are: V4L2_PIX_FMT_NV12M,
V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16, V4L2_PIX_FMT_NV16M for source and
V4L2_PIX_FMT_JPEG for destination.

During decoding the available formats are: V4L2_PIX_FMT_JPEG for source and
V4L2_PIX_FMT_NV12M, V4L2_PIX_FMT_NV16M, V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16
for destination.

Performance of current version:
1280x800 NV12 image encoding/decoding
	decoding ~122 FPS
	encoding ~191 FPS
Signed-off-by: NMikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This v4l2 mem2mem driver is a 2D blitter for STMicroelectronics SoC.
It uses the v4l2 mem2mem framework.

The following features are supported and tested:
- Color format conversion (RGB32, RGB24, RGB16, NV12, YUV420P)
- Copy
- Scale
- Flip
- Deinterlace
- Wide (4K) picture support
- Crop
Signed-off-by: NFabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: added missing slab.h include to bdisp-v4l2.c]
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Xilinx platforms have no hardwired video capture or video processing
interface. Users create capture and memory to memory processing
pipelines in the FPGA fabric to suit their particular needs, by
instantiating video IP cores from a large library.

The Xilinx Video IP core is a framework that models a video pipeline
described in the device tree and expose the pipeline to userspace
through the media controller and V4L2 APIs.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: NRadhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds Video Processing Front End (VPFE) driver for
AM437X family of devices
Driver supports the following:
- V4L2 API using MMAP buffer access based on videobuf2 api
- Asynchronous sensor/decoder sub device registration
- DT support
Signed-off-by: NBenoit Parrot <bparrot@ti.com>
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
[hans.verkuil@cisco.com: swapped two lines to fix vpfe_release() & add pinctrl include]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.

So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This is 1) *much* easier to type, and 2) is consistent with vivid
('vi' for virtual). More of such virtual drivers are planned, so keeping
the naming consistent makes sense.

Note that the old module name is retained as a module alias.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

this patch removes unneeded dependency of ARCH_OMAP3
on VIDEO_DM6446_CCDC.
Also the top level platform Makefile descended into
davinci/ without any dependency so just drop the
dependency obj-y, as obj-$(CONFIG_ARCH_DAVINCI)
already exists.
Reported-by: NAndreas Ruprecht <rupran@einserver.de>
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The vivid driver is a vastly superior test driver, so just drop the old
vivi driver.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Update the Kconfig and Makefile files so this driver can be compiled.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We don't need anything special to enable COMPILE_TEST for
this driver.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The coda driver has grown significantly and will continue to grow.
Move the coda driver into its own directory so it can be split.
Rename coda.h to coda_regs.h as it contains the register defines.
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>