- 18 1月, 2006 18 次提交
-
-
由 Stephen Hemminger 提交于
There are a couple of problems in the DMA setup code for skge. * In the 64 bit case, it doesn't set the consistent mask. * In the 32 bit case, the error check is backwards! It likely will only be visible as a bug on 64 bit platforms. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Alan Cox 提交于
sizeof() return is not an int, so use max_t to get the types right. Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Be more careful about transmit locking, this solves a possible race between tx_complete and transmit, that would cause a tx timeout. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Don't need to inline quite so many routines, let the compiler decide Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Can use kzalloc here. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Make sure and rate limit all the error messages that might occur. If a problem occurs then a few messages are enough. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Small optimization, if dma addresses are 32 bits, then high bits are always zero. Signed-off-by: NStephen Hemminger <shemminger@osdl.or> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Don't need to zero out the status ring entries after processing. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Be more careful about memory barriers. The only place we really need them is before and after updating the chip's ring interface. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from sk98lin driver. Change how the ram buffer is divided up, and make the math clearer. Also, set the thresholds where rx takes precedence. The threshold values are just guesses at this point, it might be worth tuning them later. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Version update. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Need to call pci_set_consistent_dma_mask in the case of 64 bit DMA. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Need to make sure that sky2 receive buffers are 64 bit aligned. Also, don't need to start off with GFP_ATOMIC on initial setup. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jesse Brandeburg 提交于
e100: e100 whitespace fixes These are whitespace only fixes. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jesse Brandeburg 提交于
e100: Handle the return values from pci_* functions This is to resolve warnings during compile time. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jesse Brandeburg 提交于
e100: Fix TX hang and RMCP Ping issue (due to a microcode loading issue) Set the end of list bit to cause the hardware's transmit state machine to work correctly and not prevent management (BMC) traffic. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Andrew Morton 提交于
drivers/net/cassini.c:1930: warning: long unsigned int format, different type arg (arg 4) Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 1月, 2006 22 次提交
-
-
由 Javier Achirica 提交于
-
由 Jeff Kirsher 提交于
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Improves small packet performance with large amounts of reassembly being done in the stack. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
This was to fix compilation warnings. Also added log messages when pci_enable_* functions return with an error. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
This is two patches, the first is adding additional bus information for the 8257{1|2|3} controllers. The second patch was orginally a community patch to print bus type/speed/width, and enhanced by us. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
The EEPROM image version is reported as a firmware version for these controllers. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Added 82571 fiber to WOL fix for dual port adapters. Added support for 82546GB (Quad Copper). Added PCIe typedef for x2, igp cable length 115, and extended TX CTRL registers. Added parity error detection and PCIe CTRL registers. Added EEPROM config registers. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Fixed an issue netpoll would error out during communication, generating the following error: --netdump[14973]: Got toomany timeouts in handshaking, ... Even after a kernel panic, netpoll requires two way communication to successfully transfer the crash log to the remote server. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Simplified the logic used to assign the frame_size. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Fixed VLAN support by switching control over to the firmware. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Fixed by moving code to correct location (for 82572 and 82571 controllers). Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Fixed the collision distance for 82543 controllers and newer. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Removed duplicate code, TXDCTL and TXDCTL_COUNT_DESC are the same bit and there is no need to set it twice. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
These were two separate community submitted patches. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Fixed the TX timeout logic to use "end of packet" rather than "next to clean". Updated message log. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
This patch contains two fixes. The first fix is to the tx and rx descriptor rings clean up process. The second fix is to jumbo frames, which cleans up the code logic and removes most of the fifo related limitations on jumbo frames. This is because the driver code now supports splitting a packet across multiple descriptors. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
10/100 speeds seem to have some problems reporting false tx timeouts especially at half duplex. Fixed by using a timeout factor to attempt to mitigate the false timeouts. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Fixed flow control water marks based on PBA size. Store flow control state in original_fc in addition to fc. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jeff Kirsher 提交于
Fixed read_eeprom logic to test use_eerd instead of testing for 82573 controllers. Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJohn Ronciak <john.ronciak@intel.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-