This patch resolves an issue where users were not able to dynamically
set number of queues for 82598 via ethtool -L
Reported-by: NTal Abudi <talabudi@gmail.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allows to change the rxfh indirection table and/or key using
ethtool interface.
Signed-off-by: NTom Barbette <tom.barbette@ulg.ac.be>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid a needless PHY access on copper phys to save the 10ms wait
time for each PHY access. A helper function is introduced to
actually do the register access and process the contents.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We already cache this FW/SW semaphore mask so might as well use it
for consistency.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes the redundant lan_id in the phy struct and uses
the bus version.  Both variables exist and intend to represent the
STATUS register LAN_ID field.  However, phy.lan_id is not bit shifted
so the phy.lan_id = 0x0 for LAN Id 0 and phy.lan_id = 0x4 for LAN Id 1.
Where bus.lan_id is bit shifted so bus.lan_id = 0x0 for LAN Id 0 and
bus.lan_id = 0x1 for LAN Id 1. There seems no need for the additional
lan_id variable and this should make the code less confusing.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use kzalloc rather than kcalloc(1..

The semantic patch that makes this change is as follows:

// <smpl>
@@
@@

- kcalloc(1,
+ kzalloc(
          ...)
// </smpl>

and removing checkpatch below CHECK:
CHECK: Prefer kzalloc(sizeof(*fwd_adapter)...) over
kzalloc(sizeof(struct ixgbe_fwd_adapter)...)
Signed-off-by: NManinder Singh <maninder1.s@samsung.com>
Reviewed-by: NVaneet Narang <v.narang@samsung.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ixgbe never has as very doubtfully ever will support either
PCI or PCI-X devices.  So remove the unused types from the
ixgbe_bus_type.  Thanks to Alex Duyck for suggesting this.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With this patch we add support for a new bus type ixgbe_bus_type_internal.
X550em devices use IOSF and not PCIe bus so this new type is to accommodate
them.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added ixgbe_get_bus_info_X550em to X550 code. ixgbe_get_bus_info_X550em
sets bus.width to ixgbe_bus_width_unknown and bus.speed to
ixgbe_bus_speed_unknown, because IOSF does not report a PCIe bus
width or speed.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the device is closing or suspending, call ixgbe_enter_lplu to
enter low power link up state on devices that support it. When this
is done, prevent the phy from being reset in the ixgbe_down path
so that link is present when calling ixgbe_enter_lplu.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for VXLAN RX offloads for the X55x devices that support
them.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By using GSO for UDP-encapsulated packets, all ixgbe devices can
be directed to generate checksums for the inner headers because
the outer UDP checksum can be zero. So point the machinery at the
inner headers and have the hardware generate the checksum.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Wait up to about 100 us for FDIRCMD writes to complete and return
failure indications.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are various reasons why this method may or may not need to be
defined and some of these we don't know until runtime.  So we will
set the value in get_invariants.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a support function that will indicate for the
existence of management FW.
Signed-off-by: NDonald C Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit c48a11c7 ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():

        if (page->pfmemalloc && !page->mapping)
                skb->pfmemalloc = true;

It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted.  However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone.  Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.

So the assumption is invalid if the networking code can see such a page.
And it seems it can.  We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf.  There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.

The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead.  We can reuse the index
again but define it to an impossible value (-1UL).  This is the page
index so it should never see the value that large.  Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.

The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g.  what SLAB and SLUB do).

[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7 ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: NMichal Hocko <mhocko@suse.com>
Debugged-by: NVlastimil Babka <vbabka@suse.com>
Debugged-by: NJiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: NMel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org>	[3.6+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Simplify port-specific macros by eliminating explicit comparison
with 0. More importantly, enclose formal parameter in parens to
eliminate the risk of an operator precedence surprise.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For two reasons I want to disable this:
1. Not any part actually check the report status(Alexander Duyck)
2. To report hash value of a packet to stack,
   RSS -> 32bits hash value
   Perfect match fdir filter -> 13bits hash value
   Hashed-based fdir filter -> 31bits hash value

   fdir filter might hash on masked tuples for IP address,
   so it's still not desirable for usage.

So for now, just stick to RSS 32bits hash value.
Signed-off-by: NFan Du <fan.du@intel.com>
Suggested-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

RSS could be leveraged by taking account L4 src/dst ports
as ingredients, thus ingress skb Rx hash type should honor
such the real configuration.
Signed-off-by: NFan Du <fan.du@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One more missing piece of the puzzle.  Add vlan dump support to switchdev
port's bridge_getlink.  iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg.  Before this patch, "bridge vlan show":

	$ bridge -c vlan show
	port    vlan ids
	sw1p1    30-34			<< bridge side vlans
		 57

	sw1p1				<< device side vlans (missing)

	sw1p2    57

	sw1p2

	sw1p3

	sw1p4

	br0     None

(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port.  The listing above show no vlans for the device side even though they
are installed).

After this patch:

	$ bridge -c vlan show
	port    vlan ids
	sw1p1    30-34			<< bridge side vlan
		 57

	sw1p1    30-34			<< device side vlans
		 57
		 3840 PVID

	sw1p2    57

	sw1p2    57
		 3840 PVID

	sw1p3    3842 PVID

	sw1p4    3843 PVID

	br0     None

I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump.  Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects a bug in ixgbe_setup_ixfi_x550em where we were
reading and modifying IXGBE_KRM_LINK_CTRL_1 but forgot to write the
results back.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Even though X550 may later clear this value for certain devices
set it initially to support copper.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We need to call the set_lan_id before accessing I2C and this wasn't
being done so this patch corrects that.  Likewise we do the same for
QSFP just to be consistent.

In the X550 case this is even more important as with out it the mux
is not controlled properly.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds ixgbe_check_link_t_X550em for checking copper PHY
link.  We check that both the MAC and external PHY have link. This
is to avoid a false link up between the internal and external PHY
when  the external PHY doesn't have link.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for another 10baseT X550 device.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A subset of the X550 function pointers didn't have default methods. This
didn't cause any issue with previous X550 devices as they were all
redefined.  However future devices will need these default values.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reviewing the X550 copper init flow with the Si team resulted in a
new simplified flow.  We no longer wait for the PHY FW initialization
complete bit to be set as this bit is only set once by the PHY at power
on and then cleared on the first read. So only the first instance of
running SW (or possibly MAC FW) needs to initialize the PHY.

The PHY initialization has been simplified and now only requires that
the PHY FW be un-stalled
low-power mode or enabled the transceiver
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This check was missed in when this new MAC type was added.  Since
these counts can be incremented for X550 we need to clear them.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add checks for systems that don't have SFP's to avoid incorrectly
acting on interrupts that are falsely interpreted as SFP events.
We do this by updating the ixgbe_is_sfp to be aware of the
new X550 devices.  This also includes a modified check generating
the EICR mask to be more forward-looking.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for receiving interrupts from a external copper
PHY for the X550 part.  This includes enabling, detection as well as
re-enablement.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The over heat message is displayed for multiple reasons but the text is
cut-n-pasted for each of these cases.  This patch pulls the text from the
same location.  I noticed this as I am about to add another case.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a PHY reset function ixgbe_reset_phy_t_X550em. Which
allows devices that have LASI support in enable their interrupt.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds x550 external PHY interrupt and forced 1G/10G support.
This included enabling and handling LSC and thermal sensor interrupt.
ixgbe_handle_lasi() has been added for handling the interrupts received
over SDP0 from the external 10baseT PHY. ixgbe_enable_lasi_ext_t_x550em
and ixgbe_get_lasi_ext_t_x550em have been added to X550em to enable
mask and check interrupt flags for the external PHY.

Forced 1G/10G link speed is handled via ixgbe_mac_link_t_X550em.
ixgbe_seupt_mac_link_t_X550em sets up the internal PHY and external PHY
to either iXFI (10G) or KX (1G) based on the user selected auto
advertised link speed setting. Then sets up the external PHY auto
advertised link speed.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The I2C mux control relies on the SDP setting in the ESDP register
so it is necessary to restore the value after a MAC reset.  Combine
all this functionality in to a support function.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This new method will control the PHY power state.  You pass in the
state you wish to change to (ether on or off).  For cases where this
method is not used the current PHY power state behavior is maintained.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a define for the new PHY identification as well as it's mapping
to the correct PHY type.  Also allow ethtool to identify this type
as well.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These Device ID could support both WoL and autoneg flow control. In
the case of WoL this is indicated by the eeprom.  This patch enables
these devices this support.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some of the register addresses and format where unfortunately changed
between MAC types. To get around this we add a const u32 *mvals pointer
to the ixgbe_hw struct to point to an array of mac-type-dependent
values.  These can include register offsets, masks, whatever can be in
a u32. When the ixgbe_hw struct is initialized, a pointer to the
appropriate array must be set.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>