pinconf_generic_parse_dt_config() takes a node as input and generates an
array of generic pinconfig values from the properties of this node.

As I couldn't find a mechanism to count the number of properties of a node
the function uses internally an array to accept one of parameter and copies
the real present options to a smaller variable at its end.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There exist controllers that don't support to set the pull to up or down
separately but instead automatically set the pull direction based on
embedded knowledge inside the controller, for example depending on the
selected mux function of the pin.

Therefore this patch adds another config option to use this default
pull-state for a pin where it is not possible to know or decide if the
pin will be pulled up or down.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add a new PIN_CONFIG_BIAS_BUS_HOLD pin configuration for a bus holder
pin mode (also known as bus keeper, or repeater). This is a weak latch
which drives the last value on a tristate bus. Another device on the bus
can drive the bus high or low before going tristate to change the value
driven by the pin.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add the drive strength pinconf to debugfs output (with the unit "mA").
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fixes the following type of checkpatch errors:
ERROR: space required before the open parenthesis '('
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'conf_items' is used only in this file. Silences the below
sparse warning:
drivers/pinctrl/pinconf-generic.c:37:24: warning:
symbol 'conf_items' was not declared. Should it be static?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add the support of dumping pin configuration.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Rename PIN_CONFIG_INPUT_SCHMITT_DISABLE to
PIN_CONFIG_INPUT_SCHMITT_ENABLE. It's used to make it more generialize.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add PIN_CONFIG_SLEW_RATE parameter into pinconf-generic driver.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds a definition of a generic output configuration
for a certain pin when using the generic pin configuration
library. Whereas driving pins low/high is usually a GPIO
business, you may want to set up pins into a default state
using hogs, and never touch them again. This helps out
with that scenario.

Based on a patch from Patrice Chotard.
Signed-off-by: NPatrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In Marvell PXA/MMP silicons, input schmitt disable value is 0x40, not 0.
So append new config parameter -- input schmitt disable.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is a split-off from the earlier patch set which adds generic
pin configuration for the pin controllers that want it. Since
we may have a system with mixed generic and custom pin controllers,
we pass a boolean in the pin controller ops vtable to indicate
if it is generic.

ChangeLog v1->v5:
- Follow parent patch versioning number system.
- Document the semantic meaning of return values from pin config
  get functions, so we can iterate over pins and check their
  properties from debugfs as part of the generic config code.
- Use proper cast functions in the generic debugfs pin config
  file.
- Expand generic config to optionally cover groups too.
ChangeLog v5->v6:
- Update to match underlying changes.
ChangeLog v6->v7:
- Drop DRIVE_OFF parameter, use bias high impedance for this
- Delete argument for drive modes push-pull, od and os. These
  are now just state transitions.
- Delete slew rate rising/falling due to discussions on on
  proper semantics
- Drop config wakeup, struct irq_chip does this for now, add
  back if need be.
- Set PIN_CONFIG_END to 0x7fff making room for custom config
  parameters from 0x8000 and up.
- Prefix accessor functions with pinconf_